RK2928 and RK3066 contain a dw_apb timer component, while the rk3188 uses
a slightly similar but still different timer component. But all of them
support the ARM-global-timer that got added as clocksource driver recently.
So enable support for it to get a working clocksource for rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3188 SoC shares a lot of peripherals with the rk3066 SoC,
but not all. Therefore move the common parts to a shared dtsi.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
From Simon Horman:
* renesas/dt2: (21 commits)
ARM: shmobile: bockw: fixup ether node naming
ARM: shmobile: r8a7779: add irqpin default status on DTSI
ARM: shmobile: marzen: fixup SMSC IRQ number on DTS
ARM: shmobile: bockw: add SMSC support on DTS
ARM: shmobile: r8a7778: add renesas_intc_irqpin support on DTSI
ARM: shmobile: r8a7791 SMP device tree node
ARM: shmobile: r8a7791 Arch timer device tree node
ARM: shmobile: r8a7791 IRQC device tree node
ARM: shmobile: armadillo800eva-reference: add SDHI and MMCIF interfaces
ARM: shmobile: armadillo-reference: Add PWM backlight node to DT
ARM: shmobile: r8a73a4: add a DT node for the DMAC
ARM: shmobile: r8a7790: add I2C DT nodes
ARM: shmobile: only enable used I2C interfaces in DT on all Renesas boards
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
These were used only in one intermediate variant of the pinctrl
driver but forgotten in the dtsi file. rockchip,config properties are
neither part of the actual binding nor handled by the pinctrl driver
at all, so remove them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I've tested the serial, MMC, smsc911x, wl12xx, and off-idle support
with the pinctrl patches, so it probably works better than the
board-*.c files ever did. Also the board-omap3evm.c file is broken
for the DSS, and has been for a while. Patches are welcome to fix
it in this .dts file, let's just drop the board-*.c file for this.
Note that off-idle currently requires doing request_irq() on the
wake-up pin from pinctrl-single IRQ domain until we can handle
that in some Linux generic way.
[tony@atomide.com: updated for make dtbs build fix]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the main difference between the TMDSEVM3530 and
TMDSEVM3730 is just the omap processor:
http://www.ti.com/tool/tmdsevm3530http://www.ti.com/tool/tmdsevm3730
So let's add a common file for the EVMs, and fix the description
for the omap3-evm.dst as that's clearly for the TMDSEVM3530
since it includes omap34xx.dtsi. It cannot support the TMDSEVM3730
properly, and we need a separate file for that in the following
patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
Enable wm8904 codec on at91sam9n12ek board, which is connect
to i2c0 bus with 0x1a as address.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This fixes a long-standing Integrator/CP regression from
commit 870e2928cf
"ARM: integrator-cp: convert use CLKSRC_OF for timer init"
When this code was introduced, the both aliases pointing the
system to use timer1 as primary (clocksource) and timer2
as secondary (clockevent) was ignored, and the system would
simply use the first two timers found as clocksource and
clockevent.
However this made the system timeline accelerate by a
factor x25, as it turns out that the way the clocking
actually works (totally undocumented and found after some
trial-and-error) is that timer0 runs @ 25MHz and timer1
and timer2 runs @ 1MHz. Presumably this divider setting
is a boot-on default and configurable albeit the way to
configure it is not documented.
So as a quick fix to the problem, let's mark timer0 as
disabled, so the code will chose timer1 and timer2 as it
used to.
This also deletes the two aliases for the primary and
secondary timer as they have been superceded by the
auto-selection
Cc: stable@vger.kernel.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes this week, mostly OMAP related. Nothing stands
out as particularly controversial.
Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
including the Chromebooks"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: dts: Update 5250 arch timer node with clock frequency
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.
[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)
THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.
Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.
* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
ARM: mach-omap2: board-generic: fix undefined symbol
ARM: dts: Fix pinctrl mask for omap3
ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for lvds backlight on boards
i.MX6q-SabreSD and i.MX6dl-SabreSD
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From Santosh Shilimkar:
SOC updates for Keystone II devices:
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
ARM: keystone: Enable I2C and SPI bus support
ARM: keystone: Select TI_EDMA to be able to enable SPI driver
dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
ARM: dts: keystone: Add the SPI nodes
ARM: dts: keystone: Add i2c device nodes
ARM: keystone: add PM domain support for clock management
ARM: keystone: Enable clock drivers
ARM: dts: keystone: Add clock phandle to UART nodes
ARM: dts: keystone: Add clock tree data to devicetree
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit ad871c10b ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm
Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the AES module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms. Also add Documentation file describing the data
for the SHAM module.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
OMAP4 has an DES3DES module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.
The board adds the following connectivity:
o USB OTG
o USB HOST
o HDMI
o Ethernet
o Serial Debug (3.3V)
o 2x46 pin headers
o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.
Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT nodes for TPS659038 PMIC on DRA7 boards.
It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
