LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm testing swapout workload in a two-socket Xeon machine. The workload
has 10 threads, each thread sequentially accesses separate memory
region. TLB flush overhead is very big in the workload. For each page,
page reclaim need move it from active lru list and then unmap it. Both
need a TLB flush. And this is a multthread workload, TLB flush happens
in 10 CPUs. In X86, TLB flush uses generic smp_call)function. So this
workload stress smp_call_function_many heavily.
Without patch, perf shows:
+ 24.49% [k] generic_smp_call_function_interrupt
- 21.72% [k] _raw_spin_lock
- _raw_spin_lock
+ 79.80% __page_check_address
+ 6.42% generic_smp_call_function_interrupt
+ 3.31% get_swap_page
+ 2.37% free_pcppages_bulk
+ 1.75% handle_pte_fault
+ 1.54% put_super
+ 1.41% grab_super_passive
+ 1.36% __swap_duplicate
+ 0.68% blk_flush_plug_list
+ 0.62% swap_info_get
+ 6.55% [k] flush_tlb_func
+ 6.46% [k] smp_call_function_many
+ 5.09% [k] call_function_interrupt
+ 4.75% [k] default_send_IPI_mask_sequence_phys
+ 2.18% [k] find_next_bit
swapout throughput is around 1300M/s.
With the patch, perf shows:
- 27.23% [k] _raw_spin_lock
- _raw_spin_lock
+ 80.53% __page_check_address
+ 8.39% generic_smp_call_function_single_interrupt
+ 2.44% get_swap_page
+ 1.76% free_pcppages_bulk
+ 1.40% handle_pte_fault
+ 1.15% __swap_duplicate
+ 1.05% put_super
+ 0.98% grab_super_passive
+ 0.86% blk_flush_plug_list
+ 0.57% swap_info_get
+ 8.25% [k] default_send_IPI_mask_sequence_phys
+ 7.55% [k] call_function_interrupt
+ 7.47% [k] smp_call_function_many
+ 7.25% [k] flush_tlb_func
+ 3.81% [k] _raw_spin_lock_irqsave
+ 3.78% [k] generic_smp_call_function_single_interrupt
swapout throughput is around 1400M/s. So there is around a 7%
improvement, and total cpu utilization doesn't change.
Without the patch, cfd_data is shared by all CPUs.
generic_smp_call_function_interrupt does read/write cfd_data several times
which will create a lot of cache ping-pong. With the patch, the data
becomes per-cpu. The ping-pong is avoided. And from the perf data, this
doesn't make call_single_queue lock contend.
Next step is to remove generic_smp_call_function_interrupt() from arch
code.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a helper function to check if a backing device requires stable
page writes and, if so, performs the necessary wait. Then, make it so
that all points in the memory manager that handle making pages writable
use the helper function. This should provide stable page write support
to most filesystems, while eliminating unnecessary waiting for devices
that don't require the feature.
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own stable page guarantees or they don't block at all.
The blocking behavior is back to what it was before 3.0 if you don't
have a disk requiring stable page writes.
Here's the result of using dbench to test latency on ext2:
3.8.0-rc3:
Operation Count AvgLat MaxLat
----------------------------------------
WriteX 109347 0.028 59.817
ReadX 347180 0.004 3.391
Flush 15514 29.828 287.283
Throughput 57.429 MB/sec 4 clients 4 procs max_latency=287.290 ms
3.8.0-rc3 + patches:
WriteX 105556 0.029 4.273
ReadX 335004 0.005 4.112
Flush 14982 30.540 298.634
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, the maximum write latency drops considerably with this
patch enabled. The other filesystems (ext3/ext4/xfs/btrfs) behave
similarly, but see the cover letter for those results.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset ("stable page writes, part 2") makes some key
modifications to the original 'stable page writes' patchset. First, it
provides creators (devices and filesystems) of a backing_dev_info a flag
that declares whether or not it is necessary to ensure that page
contents cannot change during writeout. It is no longer assumed that
this is true of all devices (which was never true anyway). Second, the
flag is used to relaxed the wait_on_page_writeback calls so that wait
only occurs if the device needs it. Third, it fixes up the remaining
disk-backed filesystems to use this improved conditional-wait logic to
provide stable page writes on those filesystems.
It is hoped that (for people not using checksumming devices, anyway)
this patchset will give back unnecessary performance decreases since the
original stable page write patchset went into 3.0. Sorry about not
fixing it sooner.
Complaints were registered by several people about the long write
latencies introduced by the original stable page write patchset.
Generally speaking, the kernel ought to allocate as little extra memory
as possible to facilitate writeout, but for people who simply cannot
wait, a second page stability strategy is (re)introduced: snapshotting
page contents. The waiting behavior is still the default strategy; to
enable page snapshotting, a superblock flag (MS_SNAP_STABLE) must be
set. This flag is used to bandaid^Henable stable page writeback on
ext3[1], and is not used anywhere else.
Given that there are already a few storage devices and network FSes that
have rolled their own page stability wait/page snapshot code, it would
be nice to move towards consolidating all of these. It seems possible
that iscsi and raid5 may wish to use the new stable page write support
to enable zero-copy writeout.
Thank you to Jan Kara for helping fix a couple more filesystems.
Per Andrew Morton's request, here are the result of using dbench to measure
latencies on ext2:
3.8.0-rc3:
Operation Count AvgLat MaxLat
----------------------------------------
WriteX 109347 0.028 59.817
ReadX 347180 0.004 3.391
Flush 15514 29.828 287.283
Throughput 57.429 MB/sec 4 clients 4 procs max_latency=287.290 ms
3.8.0-rc3 + patches:
WriteX 105556 0.029 4.273
ReadX 335004 0.005 4.112
Flush 14982 30.540 298.634
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, for ext2 the maximum write latency decreases from ~60ms
on a laptop hard disk to ~4ms. I'm not sure why the flush latencies
increase, though I suspect that being able to dirty pages faster gives
the flusher more work to do.
On ext4, the average write latency decreases as well as all the maximum
latencies:
3.8.0-rc3:
WriteX 85624 0.152 33.078
ReadX 272090 0.010 61.210
Flush 12129 36.219 168.260
Throughput 44.8618 MB/sec 4 clients 4 procs max_latency=168.276 ms
3.8.0-rc3 + patches:
WriteX 86082 0.141 30.928
ReadX 273358 0.010 36.124
Flush 12214 34.800 165.689
Throughput 44.9941 MB/sec 4 clients 4 procs max_latency=165.722 ms
XFS seems to exhibit similar latency improvements as ext2:
3.8.0-rc3:
WriteX 125739 0.028 104.343
ReadX 399070 0.005 4.115
Flush 17851 25.004 131.390
Throughput 66.0024 MB/sec 4 clients 4 procs max_latency=131.406 ms
3.8.0-rc3 + patches:
WriteX 123529 0.028 6.299
ReadX 392434 0.005 4.287
Flush 17549 25.120 188.687
Throughput 64.9113 MB/sec 4 clients 4 procs max_latency=188.704 ms
...and btrfs, just to round things out, also shows some latency
decreases:
3.8.0-rc3:
WriteX 67122 0.083 82.355
ReadX 212719 0.005 2.828
Flush 9547 47.561 147.418
Throughput 35.3391 MB/sec 4 clients 4 procs max_latency=147.433 ms
3.8.0-rc3 + patches:
WriteX 64898 0.101 71.631
ReadX 206673 0.005 7.123
Flush 9190 47.963 219.034
Throughput 34.0795 MB/sec 4 clients 4 procs max_latency=219.044 ms
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own wait code, or they don't block at all. The blocking
behavior is back to what it was before 3.0 if you don't have a disk
requiring stable page writes.
This patchset has been tested on 3.8.0-rc3 on x64 with ext3, ext4, and
xfs. I've spot-checked 3.8.0-rc4 and seem to be getting the same
results as -rc3.
[1] The alternative fixes to ext3 include fixing the locking order and
page bit handling like we did for ext4 (but then why not just use
ext4?), or setting PG_writeback so early that ext3 becomes extremely
slow. I tried that, but the number of write()s I could initiate dropped
by nearly an order of magnitude. That was a bit much even for the
author of the stable page series! :)
This patch:
Creates a per-backing-device flag that tracks whether or not pages must
be held immutable during writeout. Eventually it will be used to waive
wait_for_page_writeback() if nothing requires stable pages.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I recently made the mistake of writing:
foo = lockdep_dereference_protected(..., lockdep_assert_held(...));
which is clearly bogus. If lockdep is disabled in the config this would
cause a compile failure, if it is enabled then it compiles and causes a
puzzling warning about dereferencing without the correct protection.
Wrap the macro in "do { ... } while (0)" to also fail compile for this
when lockdep is enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce compiletime_assert to compiler.h, which moves the details of
how to break a build and emit an error message for a specific compiler
to the headers where these details should be. Following in the
tradition of the POSIX assert macro, compiletime_assert creates a
build-time error when the supplied condition is *false*.
Next, we add BUILD_BUG_ON_MSG to bug.h which simply wraps
compiletime_assert, inverting the logic, so that it fails when the
condition is *true*, consistent with the language "build bug on." This
macro allows you to specify the error message you want emitted when the
supplied condition is true.
Finally, we remove all other code from bug.h that mucks with these
details (BUILD_BUG & BUILD_BUG_ON), and have them all call
BUILD_BUG_ON_MSG. This not only reduces source code bloat, but also
prevents the possibility of code being changed for one macro and not for
the other (which was previously the case for BUILD_BUG and
BUILD_BUG_ON).
Since __compiletime_error_fallback is now only used in compiler.h, I'm
considering it a private macro and removing the double negation that's
now extraneous.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prior to the introduction of __attribute__((error("msg"))) in gcc 4.3,
creating compile-time errors required a little trickery.
BUILD_BUG{,_ON} uses this attribute when available to generate
compile-time errors, but also uses the negative-sized array trick for
older compilers, resulting in two error messages in some cases. The
reason it's "some" cases is that as of gcc 4.4, the negative-sized array
will not create an error in some situations, like inline functions.
This patch replaces the negative-sized array code with the new
__compiletime_error_fallback() macro which expands to the same thing
unless the the error attribute is available, in which case it expands to
do{}while(0), resulting in exactly one compile-time error on all
versions of gcc.
Note that we are not changing the negative-sized array code for the
unoptimized version of BUILD_BUG_ON, since it has the potential to catch
problems that would be disabled in later versions of gcc were
__compiletime_error_fallback used. The reason is that that an
unoptimized build can't always remove calls to an error-attributed
function call (like we are using) that should effectively become dead
code if it were optimized. However, using a negative-sized array with a
similar value will not result in an false-positive (error). The only
caveat being that it will also fail to catch valid conditions, which we
should be expecting in an unoptimized build anyway.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Negative sized arrays wont create a compile-time error in some cases
starting with gcc 4.4 (e.g., inlined functions), but gcc 4.3 introduced
the error function attribute that will.
This patch modifies BUILD_BUG_ON to behave like BUILD_BUG already does,
using the error function attribute so that you don't have to build the
entire kernel to discover that you have a problem, and then enjoy trying
to track it down from a link-time error.
Also, we are only including asm/bug.h and then expecting that
linux/compiler.h will eventually be included to define __linktime_error
(used in BUILD_BUG_ON). This patch includes it directly for clarity and
to avoid the possibility of changes in <arch>/*/include/asm/bug.h being
changed or not including linux/compiler.h for some reason.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calling BUILD_BUG_ON in an optimized build using gcc 4.3 and later,
the condition will be evaulated twice, possibily with side-effects. This
patch eliminates that error.
[akpm@linux-foundation.org: tweak code layout]
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Throughout compiler*.h, many version checks are made. These can be
simplified by using the macro that gcc's documentation recommends.
However, my primary reason for adding this is that I need bug-check
macros that are enabled at certain gcc versions and it's cleaner to use
this macro than the tradition method:
#if __GNUC__ > 4 || (__GNUC__ == 4 && __GNUC_MINOR__ => 2)
If you add patch level, it gets this ugly:
#if __GNUC__ > 4 || (__GNUC__ == 4 && (__GNUC_MINOR__ > 2 || \
__GNUC_MINOR__ == 2 __GNUC_PATCHLEVEL__ >= 1))
As opposed to:
#if GCC_VERSION >= 40201
While having separate headers for gcc 3 & 4 eliminates some of this
verbosity, they can still be cleaned up by this.
See also:
http://gcc.gnu.org/onlinedocs/cpp/Common-Predefined-Macros.html
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull pstore patches from Tony Luck:
"A few fixes to reduce places where pstore might hang a system in the
crash path. Plus a new mountpoint (/sys/fs/pstore ... makes more
sense then /dev/pstore)."
Fix up trivial conflict in drivers/firmware/efivars.c
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: Create a convenient mount point for pstore
efi_pstore: Introducing workqueue updating sysfs
efivars: Disable external interrupt while holding efivars->lock
efi_pstore: Avoid deadlock in non-blocking paths
pstore: Avoid deadlock in panic and emergency-restart path
Pull NFS client bugfixes from Trond Myklebust:
- Fix an Oops in the pNFS layoutget code
- Fix a number of NFSv4 and v4.1 state recovery deadlocks and hangs due
to the interaction of the session drain lock and state management
locks.
- Remove task->tk_xprt, which was hiding a lot of RCU dereferencing
bugs
- Fix a long standing NFSv3 posix lock recovery bug.
- Revert commit 324d003b0c ("NFS: add nfs_sb_deactive_async to avoid
deadlock"). It turned out that the root cause of the deadlock was
due to interactions with the workqueues that have now been resolved.
* tag 'nfs-for-3.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (22 commits)
NLM: Ensure that we resend all pending blocking locks after a reclaim
umount oops when remove blocklayoutdriver first
sunrpc: silence build warning in gss_fill_context
nfs: remove kfree() redundant null checks
NFSv4.1: Don't decode skipped layoutgets
NFSv4.1: Fix bulk recall and destroy of layouts
NFSv4.1: Fix an ABBA locking issue with session and state serialisation
NFSv4: Fix a reboot recovery race when opening a file
NFSv4: Ensure delegation recall and byte range lock removal don't conflict
NFSv4: Fix up the return values of nfs4_open_delegation_recall
NFSv4.1: Don't lose locks when a server reboots during delegation return
NFSv4.1: Prevent deadlocks between state recovery and file locking
NFSv4: Allow the state manager to mark an open_owner as being recovered
SUNRPC: Add missing static declaration to _gss_mech_get_by_name
Revert "NFS: add nfs_sb_deactive_async to avoid deadlock"
SUNRPC: Nuke the tk_xprt macro
SUNRPC: Avoid RCU dereferences in the transport bind and connect code
SUNRPC: Fix an RCU dereference in xprt_reserve
SUNRPC: Pass pointers to struct rpc_xprt to the congestion window
SUNRPC: Fix an RCU dereference in xs_local_rpcbind
...
Pull fuse updates from Miklos Szeredi:
"The biggest part of this pull request is a patch series from Maxim
Patlasov to optimize scatter-gather direct IO. There's also the
addition of a "readdirplus" API, poll events and various fixes and
cleanups.
There's a one line change outside of fuse to mm/filemap.c which makes
the argument of iov_iter_single_seg_count() const, required by Maxim's
patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: (22 commits)
fuse: allow control of adaptive readdirplus use
Synchronize fuse header with one used in library
fuse: send poll events
fuse: don't WARN when nlink is zero
fuse: avoid out-of-scope stack access
fuse: bump version for READDIRPLUS
FUSE: Adapt readdirplus to application usage patterns
Do not use RCU for current process credentials
fuse: cleanup fuse_direct_io()
fuse: optimize __fuse_direct_io()
fuse: optimize fuse_get_user_pages()
fuse: pass iov[] to fuse_get_user_pages()
mm: minor cleanup of iov_iter_single_seg_count()
fuse: use req->page_descs[] for argpages cases
fuse: add per-page descriptor <offset, length> to fuse_req
fuse: rework fuse_do_ioctl()
fuse: rework fuse_perform_write()
fuse: rework fuse_readpages()
fuse: rework fuse_retrieve()
fuse: categorize fuse_get_req()
...
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
Pull device tree changes from Grant Likely:
"All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (23 commits)
Revert "of: use platform_device_add"
kbuild: limit dtc+cpp include path
gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
of: Create function for counting number of phandles in a property
of/base: Clean up exit paths for of_parse_phandle_with_args()
of/selftest: Use selftest() macro throughout
of/selftest: Fix GPIOs selftest to cover the 7th case
of: fix recursive locking in of_get_next_available_child()
documentation/devicetree: Fix a typo in exynos-dw-mshc.txt
OF: convert devtree lock from rw_lock to raw spinlock
of/exynos_g2d: Add Bindings for exynos G2D driver
kbuild: create a rule to run the pre-processor on *.dts files
input: Extend matrix-keypad device tree binding
devicetree: Move NS2 LEDs binding into LEDs directory
of: use platform_device_add
powerpc/5200: Fix size to request_mem_region() call
documentation/devicetree: Fix typos
of: add 'const' to of_node_full_name parameter
of: Output devicetree alias names in uevent
DT: add vendor prefixes for Renesas and Toshiba
...
Pull SPI changes from Grant Likely:
"Changes to both core spi code and spi device drivers. The driver
changes are the usual set of bug fixes and platform enablement.
Core code changes include:
- More intelligent assignment of SPI bus numbers when using DT
- Common mechanism for using gpios as CS lines
- Pull checks for bits_per_word and transfer speed out of drivers and
into core code
- Ensure temporary DMA buffers are DMA safe"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux: (50 commits)
spi: Document cs_gpios and cs_gpio in kernel-doc
spi/of: Fix initialization of cs_gpios array
spi/pxa2xx: add support for Lynxpoint SPI controllers
spi/pxa2xx: add support for Intel Low Power Subsystem SPI
spi/pxa2xx: add support for SPI_LOOP
spi/pxa2xx: add support for runtime PM
spi/pxa2xx: add support for DMA engine
spi/pxa2xx: break out the private DMA API usage into a separate file
spi/ath79: add shutdown handler
spi/mips-lantiq: set SPI_MASTER_HALF_DUPLEX flag
spi/mips-lantiq: make use of spi_finalize_current_message
spi/bcm63xx: work around inability to keep CS up
spi/davinci: use request_threaded_irq() to fix deadlock
spi/orion: Use module_platform_driver()
spi/bcm63xx: reject transfers unable to transfer
spi: Ensure memory used for spi_write_then_read() is DMA safe
spi/spi-mpc512x-psc: init mode bits supported by the driver
spi/mpc512x-psc: don't use obsolet cell-index property
spi: Remove erroneous __init, __exit and __exit_p() references in drivers
spi/s3c64xx: fix checkpatch warnings and error
...
Pull clock framework update from Michael Turquette:
"The common clock framework changes for 3.9 are almost entirely fixes.
None are dire enough to be Cc'd to stable which may be interpreted to
mean that users of the framework are reaching stability. Lots of new
adoption of this framework is via DeviceTree data and that comes
through the respective architecture and platform trees instead of
through the clk framework tree.
Two new features are improved debugfs output and an improvement to how
DT clocks are initialized by reusing a common method."
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (25 commits)
clk: sunxi: remove stale Makefile entry
clk: vexpress: Use common of_clk_init() function
clk: zynq: Use common of_clk_init() function
clk: vt8500: Use common of_clk_init() function
clk: highbank: Use common of_clk_init() function
clk: sunxi: Use common of_clk_init() function
clk: add common of_clk_init() function
clk: Deduplicate exit code in clk_set_rate
clk: beautify Makefile
clk-divider: fix macros
clk: prima2: enable dt-binding clkdev mapping
clk: mxs: Index is always positive
clk: max77686: Avoid double free at remove time
clk: remove exported function from __init section
clk: vt8500: Add support for WM8750/WM8850 PLL clocks
clk: vt8500: Fix division-by-0 when requested rate=0
clk: vt8500: Fix device clock divisor calculations
clk: vt8500: Fix error in PLL calculations on non-exact match.
clk: max77686: Remove unnecessary NULL checking for container_of()
clk: JSON debugfs clock tree summary
...
Pull input updates from Dmitry Torokhov:
"Two new touchpad drivers - Cypress APA I2C Trackpad and Cypress PS/2
touchpad and a big update to ALPS driver from Kevin Cernekee that adds
support for "Rushmore" touchpads and paves way for adding support for
"Dolphin" touchpads.
There is also a new input driver for Goldfish emulator and also
Android keyreset driver was folded into SysRq code.
A few more drivers were updated with device tree bindings and others
got some small cleanups and fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: cyttsp-spi - remove duplicate MODULE_ALIAS()
Input: tsc2005 - add MODULE_ALIAS
Input: tegra-kbc - require CONFIG_OF, remove platform data
Input: synaptics - initialize pointer emulation usage
Input: MT - do not apply filtering on emulated events
Input: bma150 - make some defines public and fix some comments
Input: bma150 - fix checking pm_runtime_get_sync() return value
Input: ALPS - enable trackstick on Rushmore touchpads
Input: ALPS - add support for "Rushmore" touchpads
Input: ALPS - make the V3 packet field decoder "pluggable"
Input: ALPS - move pixel and bitmap info into alps_data struct
Input: ALPS - fix command mode check
Input: ALPS - rework detection of Pinnacle AGx touchpads
Input: ALPS - move {addr,nibble}_command settings into alps_set_defaults()
Input: ALPS - use function pointers for different protocol handlers
Input: ALPS - rework detection sequence
Input: ALPS - introduce helper function for repeated commands
Input: ALPS - move alps_get_model() down below hw_init code
Input: ALPS - copy "model" info into alps_data struct
Input: ALPS - document the alps.h data structures
...
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
Pull hwmon updates from Guenter Roeck:
- New drivers for MAX6697 and compatibles and for INA209.
- Added support for IT8771E, IT8772E, MAX34460, MAX34461, MCP98244, and
ADT7420 to existing drivers.
- Added support for additional attributes to various drivers.
- Replaced SENSORS_LIMIT with clamp_val; retire SENSORS_LIMIT;
- Clean up PMBus code to reduce its size; clean up adt7410 driver.
- A couple of minor bug fixes as well as documentation cleanup.
- Out-of-tree change: Replace SENSORS_LIMIT with clamp_val in
platform/x86/eeepc-laptop driver.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (ntc_thermistor): Fix sparse warnings
hwmon: (adt7410) Add device table entry for the adt7420
hwmon: (adt7410) Use I2C_ADDRS helper macro
hwmon: (adt7410) Use the SIMPLE_DEV_PM_OPS helper macro
hwmon: (adt7410) Let suspend/resume depend on CONFIG_PM_SLEEP
hwmon: (adt7410) Clear unwanted bits in the config register
hwmon: (jc42) Add support for MCP98244
hwmon: (pmbus) Clean up for code size reduction
hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461
hwmon: (pmbus) Add support for word status register
hwmon: (pmbus/zl6100) Add support for VMON/VDRV
hwmon: (pmbus) Add function to clear sensor cache
hwmon: (pmbus) Add support for additional voltage sensor
hwmon: (pmbus) Use krealloc to allocate attribute memory
hwmon: (pmbus) Simplify memory allocation for sensor attributes
hwmon: (pmbus) Improve boolean handling
hwmon: (pmbus) Simplify memory allocation for labels and booleans
hwmon: (pmbus) Use dev variable to represent client->dev
hwmon: (pmbus) Fix 'Macros with multiple statements' checkpatch error
hwmon: (pmbus) Drop unnecessary error messages in probe error path
...
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
Pull regulator updates from Mark Brown:
"A fairly quiet release for the regulator API, the bulk of the changes
being lots of small cleanups and API updates contributed by Axel Lin
with just a small set of larger changes:
- New driver for LP8755
- DT support for S5M8767, TPS51632, TPS6507x and TPS65090
- Support for writing a "commit changes" bit in the regmap helper
functions."
* tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (60 commits)
regulator: Fix memory garbage dev_err printout.
regulator: max77686: Reuse rdev_get_id() function.
regulator: tps51632: Use regulator_[get|set]_voltage_sel_regmap
regulator: as3711: Fix checking if no platform initialization data
regulator: s5m8767: Prevent possible NULL pointer dereference
regulator: s5m8767: Fix dev argument for devm_kzalloc and of_get_regulator_init_data
regulator: core: Optimize _regulator_do_set_voltage if voltage does not change
regulator: max8998: Let regulator core handle the case selector == old_selector
regulator: s5m8767: Use of_get_child_count()
regulator: anatop: improve precision of delay time
regulator: show state for GPIO-controlled regulators
regulator: s5m8767: Fix build in non-DT case
regulator: add device tree support for s5m8767
regulator: palmas: Remove a redundant setting for warm_reset
regulator: mc13xxx: Use of_get_child_count()
regulator: max8997: Use of_get_child_count()
regulator: tps65090: Fix using wrong dev argument for calling of_regulator_match
regulators: anatop: add set_voltage_time_sel interface
regulator: Add missing of_node_put()
regulator: tps6507x: Fix using wrong dev argument for calling of_regulator_match
...
Pull regmap updates from Mark Brown:
"Several nice new features and performance improvements here,
especially the first:
- Support for using the cache infrastructure without the physical
I/O, allowing devices which don't fit the physical model regmap has
to take advantage of the cache infrastructure, contributed by
Andrey Smirnov.
- Several small improvements to the support for wake capable IRQs.
- Support for asynchronous I/O, allowing us to come much closer to
saturating fast buses like SPI.
- Support for simple array caches, giving higher performance for use
with MMIO devices.
- Restoration of the use of bulk reads for handling interrupts,
giving a performance improvement.
- Support for 24 bit register addresses.
- More performance improvements for debugfs."
* tag 'regmap-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (24 commits)
regmap: mmio: add register clock support
regmap: debugfs: Factor out debugfs_tot_len calc into a function
regmap: debugfs: Optimize seeking within blocks of registers
regmap: debugfs: Add a `max_reg' member in struct regmap_debugfs_off_cache
regmap: debugfs: Fix reading in register field units
regmap: spi: Handle allocation failures gracefully
regmap: Export regmap_async_complete()
regmap: Export regmap_async_complete_cb
regmap: include linux/sched.h to fix build
regmap: spi: Support asynchronous I/O for SPI
regmap: Add asynchronous I/O support
regmap: Add "no-bus" option for regmap API
regmap: regmap: avoid spurious warning in regmap_read_debugfs
regmap: Add provisions to have user-defined write operation
regmap: Add provisions to have user-defined read operation
regmap: Add support for 24 bit wide register addresses
mfd: wm5110: Mark wakes as inverted
mfd: wm5102: Mark wakes as inverted
regmap: irq: Support wake IRQ mask inversion
regmap: irq: Fix sync of wake statuses to hardware
...
Pull cgroup changes from Tejun Heo:
"Nothing too drastic.
- Removal of synchronize_rcu() from userland visible paths.
- Various fixes and cleanups from Li.
- cgroup_rightmost_descendant() added which will be used by cpuset
changes (it will be a separate pull request)."
* 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fail if monitored file and event_control are in different cgroup
cgroup: fix cgroup_rmdir() vs close(eventfd) race
cpuset: fix cpuset_print_task_mems_allowed() vs rename() race
cgroup: fix exit() vs rmdir() race
cgroup: remove bogus comments in cgroup_diput()
cgroup: remove synchronize_rcu() from cgroup_diput()
cgroup: remove duplicate RCU free on struct cgroup
sched: remove redundant NULL cgroup check in task_group_path()
sched: split out css_online/css_offline from tg creation/destruction
cgroup: initialize cgrp->dentry before css_alloc()
cgroup: remove a NULL check in cgroup_exit()
cgroup: fix bogus kernel warnings when cgroup_create() failed
cgroup: remove synchronize_rcu() from rebind_subsystems()
cgroup: remove synchronize_rcu() from cgroup_attach_{task|proc}()
cgroup: use new hashtable implementation
cgroups: fix cgroup_event_listener error handling
cgroups: move cgroup_event_listener.c to tools/cgroup
cgroup: implement cgroup_rightmost_descendant()
cgroup: remove unused dummy cgroup_fork_callbacks()
Pull async changes from Tejun Heo:
"These are followups for the earlier deadlock issue involving async
ending up waiting for itself through block requesting module[1]. The
following changes are made by these commits.
- Instead of requesting default elevator on each request_queue init,
block now requests it once early during boot.
- Kmod triggers warning if invoked from an async worker.
- Async synchronization implementation has been reimplemented. It's
a lot simpler now."
* 'for-3.9-async' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
async: initialise list heads to fix crash
async: replace list of active domains with global list of pending items
async: keep pending tasks on async_domain and remove async_pending
async: use ULLONG_MAX for infinity cookie value
async: bring sanity to the use of words domain and running
async, kmod: warn on synchronous request_module() from async workers
block: don't request module during elevator init
init, block: try to load default elevator module early during boot
Pull workqueue changes from Tejun Heo:
"A lot of reorganization is going on mostly to prepare for worker pools
with custom attributes so that workqueue can replace custom pool
implementations in places including writeback and btrfs and make CPU
assignment in crypto more flexible.
workqueue evolved from purely per-cpu design and implementation, so
there are a lot of assumptions regarding being bound to CPUs and even
unbound workqueues are implemented as an extension of the model -
workqueues running on the special unbound CPU. Bulk of changes this
round are about promoting worker_pools as the top level abstraction
replacing global_cwq (global cpu workqueue). At this point, I'm
fairly confident about getting custom worker pools working pretty soon
and ready for the next merge window.
Lai's patches are replacing the convoluted mb() dancing workqueue has
been doing with much simpler mechanism which only depends on
assignment atomicity of long. For details, please read the commit
message of 0b3dae68ac ("workqueue: simplify is-work-item-queued-here
test"). While the change ends up adding one pointer to struct
delayed_work, the inflation in percentage is less than five percent
and it decouples delayed_work logic a lot more cleaner from usual work
handling, removes the unusual memory barrier dancing, and allows for
further simplification, so I think the trade-off is acceptable.
There will be two more workqueue related pull requests and there are
some shared commits among them. I'll write further pull requests
assuming this pull request is pulled first."
* 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (37 commits)
workqueue: un-GPL function delayed_work_timer_fn()
workqueue: rename cpu_workqueue to pool_workqueue
workqueue: reimplement is_chained_work() using current_wq_worker()
workqueue: fix is_chained_work() regression
workqueue: pick cwq instead of pool in __queue_work()
workqueue: make get_work_pool_id() cheaper
workqueue: move nr_running into worker_pool
workqueue: cosmetic update in try_to_grab_pending()
workqueue: simplify is-work-item-queued-here test
workqueue: make work->data point to pool after try_to_grab_pending()
workqueue: add delayed_work->wq to simplify reentrancy handling
workqueue: make work_busy() test WORK_STRUCT_PENDING first
workqueue: replace WORK_CPU_NONE/LAST with WORK_CPU_END
workqueue: post global_cwq removal cleanups
workqueue: rename nr_running variables
workqueue: remove global_cwq
workqueue: remove worker_pool->gcwq
workqueue: replace for_each_worker_pool() with for_each_std_worker_pool()
workqueue: make freezing/thawing per-pool
workqueue: make hotplug processing per-pool
...
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
Pull timer changes from Ingo Molnar:
"Main changes:
- ntp: Add CONFIG_RTC_SYSTOHC: a generic RTC driver facility
complementing the existing CONFIG_RTC_HCTOSYS, which uses NTP to
keep the hardware clock updated.
- posix-timers: Fix clock_adjtime to always return timex data on
success. This is changing the ABI, but no breakage was expected
and found - caution is warranted nevertheless.
- platform persistent clock improvements/cleanups.
- clockevents: refactor timer broadcast handling to be more generic
and less duplicated with matching architecture code (mostly ARM
motivated.)
- various fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers/x86/hpet: Use HPET_COUNTER to specify the hpet counter in vread_hpet()
posix-cpu-timers: Fix nanosleep task_struct leak
clockevents: Fix generic broadcast for FEAT_C3STOP
time, Fix setting of hardware clock in NTP code
hrtimer: Prevent hrtimer_enqueue_reprogram race
clockevents: Add generic timer broadcast function
clockevents: Add generic timer broadcast receiver
timekeeping: Switch HAS_PERSISTENT_CLOCK to ALWAYS_USE_PERSISTENT_CLOCK
x86/time/rtc: Don't print extended CMOS year when reading RTC
x86: Select HAS_PERSISTENT_CLOCK on x86
timekeeping: Add CONFIG_HAS_PERSISTENT_CLOCK option
rtc: Skip the suspend/resume handling if persistent clock exist
timekeeping: Add persistent_clock_exist flag
posix-timers: Fix clock_adjtime to always return timex data on success
Round the calculated scale factor in set_cyc2ns_scale()
NTP: Add a CONFIG_RTC_SYSTOHC configuration
MAINTAINERS: Update John Stultz's email
time: create __getnstimeofday for WARNless calls
Pull preparatory smp/hotplug patches from Ingo Molnar:
"Some early preparatory changes for the WIP hotplug rework by Thomas
Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine: Use smpboot threads
stop_machine: Store task reference in a separate per cpu variable
smpboot: Allow selfparking per cpu threads
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Pull perf changes from Ingo Molnar:
"There are lots of improvements, the biggest changes are:
Main kernel side changes:
- Improve uprobes performance by adding 'pre-filtering' support, by
Oleg Nesterov.
- Make some POWER7 events available in sysfs, equivalent to what was
done on x86, from Sukadev Bhattiprolu.
- tracing updates by Steve Rostedt - mostly misc fixes and smaller
improvements.
- Use perf/event tracing to report PCI Express advanced errors, by
Tony Luck.
- Enable northbridge performance counters on AMD family 15h, by Jacob
Shin.
- This tracing commit:
tracing: Remove the extra 4 bytes of padding in events
changes the ABI. All involved parties (PowerTop in particular)
seem to agree that it's safe to do now with the introduction of
libtraceevent, but the devil is in the details ...
Main tooling side changes:
- Add 'event group view', from Namyung Kim:
To use it, 'perf record' should group events when recording. And
then perf report parses the saved group relation from file header
and prints them together if --group option is provided. You can
use the 'perf evlist' command to see event group information:
$ perf record -e '{ref-cycles,cycles}' noploop 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.385 MB perf.data (~16807 samples) ]
$ perf evlist --group
{ref-cycles,cycles}
With this example, default perf report will show you each event
separately.
You can use --group option to enable event group view:
$ perf report --group
...
# group: {ref-cycles,cycles}
# ========
# Samples: 7K of event 'anon group { ref-cycles, cycles }'
# Event count (approx.): 6876107743
#
# Overhead Command Shared Object Symbol
# ................ ....... ................. ..........................
99.84% 99.76% noploop noploop [.] main
0.07% 0.00% noploop ld-2.15.so [.] strcmp
0.03% 0.00% noploop [kernel.kallsyms] [k] timerqueue_del
0.03% 0.03% noploop [kernel.kallsyms] [k] sched_clock_cpu
0.02% 0.00% noploop [kernel.kallsyms] [k] account_user_time
0.01% 0.00% noploop [kernel.kallsyms] [k] __alloc_pages_nodemask
0.00% 0.00% noploop [kernel.kallsyms] [k] native_write_msr_safe
0.00% 0.11% noploop [kernel.kallsyms] [k] _raw_spin_lock
0.00% 0.06% noploop [kernel.kallsyms] [k] find_get_page
0.00% 0.02% noploop [kernel.kallsyms] [k] rcu_check_callbacks
0.00% 0.02% noploop [kernel.kallsyms] [k] __current_kernel_time
As you can see the Overhead column now contains both of ref-cycles
and cycles and header line shows group information also - 'anon
group { ref-cycles, cycles }'. The output is sorted by period of
group leader first.
- Initial GTK+ annotate browser, from Namhyung Kim.
- Add option for runtime switching perf data file in perf report,
just press 's' and a menu with the valid files found in the current
directory will be presented, from Feng Tang.
- Add support to display whole group data for raw columns, from Jiri
Olsa.
- Add per processor socket count aggregation in perf stat, from
Stephane Eranian.
- Add interval printing in 'perf stat', from Stephane Eranian.
- 'perf test' improvements
- Add support for wildcards in tracepoint system name, from Jiri
Olsa.
- Add anonymous huge page recognition, from Joshua Zhu.
- perf build-id cache now can show DSOs present in a perf.data file
that are not in the cache, to integrate with build-id servers being
put in place by organizations such as Fedora.
- perf top now shares more of the evsel config/creation routines with
'record', paving the way for further integration like 'top'
snapshots, etc.
- perf top now supports DWARF callchains.
- Fix mmap limitations on 32-bit, fix from David Miller.
- 'perf bench numa mem' NUMA performance measurement suite
- ... and lots of fixes, performance improvements, cleanups and other
improvements I failed to list - see the shortlog and git log for
details."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (270 commits)
perf/x86/amd: Enable northbridge performance counters on AMD family 15h
perf/hwbp: Fix cleanup in case of kzalloc failure
perf tools: Fix build with bison 2.3 and older.
perf tools: Limit unwind support to x86 archs
perf annotate: Make it to be able to skip unannotatable symbols
perf gtk/annotate: Fail early if it can't annotate
perf gtk/annotate: Show source lines with gray color
perf gtk/annotate: Support multiple event annotation
perf ui/gtk: Implement basic GTK2 annotation browser
perf annotate: Fix warning message on a missing vmlinux
perf buildid-cache: Add --update option
uprobes/perf: Avoid uprobe_apply() whenever possible
uprobes/perf: Teach trace_uprobe/perf code to use UPROBE_HANDLER_REMOVE
uprobes/perf: Teach trace_uprobe/perf code to pre-filter
uprobes/perf: Teach trace_uprobe/perf code to track the active perf_event's
uprobes: Introduce uprobe_apply()
perf: Introduce hw_perf_event->tp_target and ->tp_list
uprobes/perf: Always increment trace_uprobe->nhit
uprobes/tracing: Kill uprobe_trace_consumer, embed uprobe_consumer into trace_uprobe
uprobes/tracing: Introduce is_trace_uprobe_enabled()
...
Pull irq core changes from Ingo Molnar:
"The biggest changes are the IRQ-work and printk changes from Frederic
Weisbecker, which prepare the code for 'full dynticks' (the ability to
stop or slow down the periodic tick arbitrarily, not just in idle time
as today):
- Don't stop tick with irq works pending. This fix is generally
useful and concerns archs that can't raise self IPIs.
- Flush irq works before CPU offlining.
- Introduce "lazy" irq works that can wait for the next tick to be
executed, unless it's stopped.
- Implement klogd wake up using irq work. This removes the ad-hoc
printk_tick()/printk_needs_cpu() hooks and make it working even in
dynticks mode.
- Cleanups and fixes."
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Export enable/disable_percpu_irq()
arch Kconfig: Remove references to IRQ_PER_CPU
irq_work: Remove return value from the irq_work_queue() function
genirq: Avoid deadlock in spurious handling
printk: Wake up klogd using irq_work
irq_work: Make self-IPIs optable
irq_work: Warn if there's still work on cpu_down
irq_work: Flush work on CPU_DYING
irq_work: Don't stop the tick with pending works
nohz: Add API to check tick state
irq_work: Remove CONFIG_HAVE_IRQ_WORK
irq_work: Fix racy check on work pending flag
irq_work: Fix racy IRQ_WORK_BUSY flag setting
Pull RCU changes from Ingo Molnar:
"SRCU changes:
- These include debugging aids, updates that move towards the goal of
permitting srcu_read_lock() and srcu_read_unlock() to be used from
idle and offline CPUs, and a few small fixes.
Changes to rcutorture and to RCU documentation:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/188
Enhancements to uniprocessor handling in tiny RCU:
- Posted to LKML at https://lkml.org/lkml/2013/1/27/2
Tag RCU callbacks with grace-period number to simplify callback
advancement:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/203
Miscellaneous fixes:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/204"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
srcu: use ACCESS_ONCE() to access sp->completed in srcu_read_lock()
srcu: Update synchronize_srcu_expedited()'s comments
srcu: Update synchronize_srcu()'s comments
srcu: Remove checks preventing idle CPUs from calling srcu_read_lock()
srcu: Remove checks preventing offline CPUs from calling srcu_read_lock()
srcu: Simple cleanup for cleanup_srcu_struct()
srcu: Add might_sleep() annotation to synchronize_srcu()
srcu: Simplify __srcu_read_unlock() via this_cpu_dec()
rcu: Allow rcutorture to be built at low optimization levels
rcu: Make rcutorture's shuffler task shuffle recently added tasks
rcu: Allow TREE_PREEMPT_RCU on UP systems
rcu: Provide RCU CPU stall warnings for tiny RCU
context_tracking: Add comments on interface and internals
rcu: Remove obsolete Kconfig option from comment
rcu: Remove unused code originally used for context tracking
rcu: Consolidate debugging Kconfig options
rcu: Correct 'optimized' to 'optimize' in header comment
rcu: Trace callback acceleration
rcu: Tag callback lists with corresponding grace-period number
rcutorture: Don't compare ptr with 0
...
commit d4beaa66ad
"net: proc: change proc_net_fops_create to proc_create"
uses proc_create to replace proc_net_fops_create, when
CONFIG_PROC isn't configured, some build error will
occurs.
net/packet/af_packet.c: In function 'packet_net_init':
net/packet/af_packet.c:3831:48: error: 'packet_seq_fops' undeclared (first use in this function)
net/packet/af_packet.c:3831:48: note: each undeclared identifier is reported only once for each function it appears in
There may be other build fails like above,this patch
change proc_create from function to macros when CONFIG_PROC
is not configured,just like what proc_net_fops_create did
before this commit.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contain updates for your net-next tree, they are:
* Fix (for just added) connlabel dependencies, from Florian Westphal.
* Add aliasing support for conntrack, thus users can either use -m state
or -m conntrack from iptables while using the same kernel module, from
Jozsef Kadlecsik.
* Some code refactoring for the CT target to merge common code in
revision 0 and 1, from myself.
* Add aliasing support for CT, based on patch from Jozsef Kadlecsik.
* Add one mutex per nfnetlink subsystem, from myself.
* Improved logging for packets that are dropped by helpers, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This probably is the last big pull request for wireless bits
for 3.9. Of course, I'm sure there will be a few stragglers here
and there...surely a few bug fixes as well... :-) (In fact, I see
that Johannes has already queued-up a few more for me while I was
preparing this...)
Included are a number of pulls...
For mac80211-next, Johannes says:
"The biggest change I have is undoubtedly Marco's mesh powersave
implementation. Beyond that, I have a patch from Emmanuel to modify the
DTIM period API in mac80211, scan improvements and a removal of some
previous workaround code from Stanislaw, dynamic short slot time from
Thomas and 64-bit station byte counters from Vladimir. I also made a
number of changes myself, some related to WoWLAN, some auth/deauth
improvements and most of them BSS list cleanups."
"This time, I have relatively large number of fixes in various areas of
the code (a memory leak in regulatory, an RX race in mac80211, the new
radar checking caused a P2P device problem, some mesh issues with
stations, an older bug in tracing and for kernel-doc) as well as a
number of small new features. The biggest (in the diffstat) is my work
on hidden SSID tracking."
"Please pull to get
* radar detection work from Simon
* mesh improvements from Thomas
* a connection monitoring/powersave fix from Wojciech
* TDLS-related station management work from Jouni
* VLAN crypto fixes from Michael Braun
* CCK support in minstrel_ht from Felix
* an SMPS (not SMSP, oops) related improvement in mac80211 (Emmanuel)
* some WoWLAN work from Amitkumar Karwar: pattern match offset and a
documentation fix
* some WoWLAN work from myself (TCP connection wakeup feature API)
* and a lot of VHT (and some HT) work (also from myself)
And a number of more random cleanups/fixes. I merged mac80211/master to
avoid a merge problem there."
And regarding iwlwifi-next, Johannes says:
"We continue work on our new driver, but I also have a WoWLAN and AP mode
improvement for the previous driver and a change to use threaded
interrupts to prepare us for working with non-PCIe devices."
Regarding wl12xx, Luca says:
"A few more patches intended for 3.9. Mostly some clean-ups I've been
doing to make it easier to support device-tree. Also including one bug
fix for wl12xx where the rates we advertise were wrong and an update in
the wlconf structure to support newer firmwares."
For the nfc-next bits, Samuel says:
"This is the second NFC pull request for 3.9.
We have:
- A few pn533 fixes on top of Waldemar refactorization of the driver, one of
them fixes target mode.
- A new driver for Inside Secure microread chipset. It supports two
physical layers: i2c and MEI. The MEI one depends on a patchset that's
been sent to Greg Kroah-Hartman for inclusion into the 3.9 kernel [1]. The
dependency is a KConfig one which means this code is not buildable as long
as the MEI API is not usptream."
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
For the ath6kl bits, Kalle says:
"There's not anything special here, most of the patches are just code
cleanup. The only functional changes are using the beacon interval from user
space and fixing a crash which happens when inserting and removing the
module in a loop."
Also, I pulled the wireless tree in order to resolve some pending
merge issues. On top of that, there is a bunch of work on brcmfmac
that leads up to P2P support. Also, mwifiex, rtlwifi, and a variety
of other drivers see some basic cleanups and minor enhancements.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove has been replaced by remove_proc_entry.
we can remove it now.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
