Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
The blackfin architecture is getting removed, so these are
now obsolete.
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This driver is a pure GPIO driver and should only include
<linux/gpio/driver.h>. Drop the include of <linux/gpio.h>
from the platform data header as well, it serves no purpose.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
ARM: pxa: cm-x300: remove inline directive
ARM: pxa: fix static checker warning in pxa3xx-ulpi
MAINTAINERS: remove entry for deleted pxa3xx_nand driver
arm: dts: pxa: use reworked NAND controller driver
dt-bindings: mtd: remove pxa3xx NAND controller documentation
mtd: nand: remove useless fields from pxa3xx NAND platform data
mtd: nand: remove deprecated pxa3xx_nand driver
mtd: nand: use Marvell reworked NAND controller driver with all platforms
Pull "Driver changes for ti-sysc for v4.17" from Tony Lindgren:
This series of changes enables the use device tree based sysconfig
data for ti-sysc driver. As we already have SmartReflex data configured,
we use that as the first driver to enable. To do that in a way where
SmartReflex is not probed twice, we need to prepare the SmartReflex
driver before flipping dts data on for it in the last patch of the
series.
To avoid regressions, we are checking the passed dts data against
existing platform data since we still have it available. Then after the
dts files are converted, we can simply drop the related platform data
at some point in the future.
* tag 'omap-for-v4.17/ti-sysc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable ti-sysc to use device tree data for smartreflex
PM / AVS: SmartReflex: Prepare to use device tree based probing
ARM: OMAP2+: Try to parse earlycon from parent too
ARM: OMAP2+: Add checks for device tree based sysconfig data
ARM: OMAP2+: Add functions to allocate module data from device tree
bus: ti-sysc: Handle some devices in omap_device compatible way
bus: ti-sysc: Add support for platform data callbacks
bus: ti-sysc: Remove unnecessary debugging statements
bus: ti-sysc: Improve handling for no-reset-on-init and no-idle-on-init
bus: ti-sysc: Handle stdout-path for debug console
bus: ti-sysc: Add suspend and resume handling
bus: ti-sysc: Add fck clock alias for children with notifier_block
ARM: OMAP2+: Prepare to pass auxdata for smartreflex
Pull "Add am335x and am437x PM code for v4.17" from Tony Lindgren:
This series of changes from Dave Gerlach adds the PM related
code to allow low-power suspend states. The code consists of
the SoC specific assembly code and a related PM driver.
* tag 'omap-for-v4.17/am-pm-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: Add pm33xx driver for basic suspend support
ARM: OMAP2+: pm33xx-core: Add platform code needed for PM
ARM: OMAP2+: Introduce low-level suspend code for AM43XX
ARM: OMAP2+: Introduce low-level suspend code for AM33XX
Pull "Move omap timer to drivers for 4.17" from Tony Lindgren:
This series from Keerthy and Ladislav Michl move omap dmtimer code
to drivers. As we don't want to export custom timer functions to
random drivers, we also need to update the related PWM driver to
pass the timer specific functions in platform data.
Note that this series is based on a merge of omap1 specific timer
fix and omap2+ platform data clean-up to keep things working and
make the move a bit simpler.
* tag 'omap-for-v4.17/timer-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
clocksource: timer-ti-dm: Check prescaler value
clocksource: timer-ti-dm: Consolidate set source
clocksource: timer-ti-dm: Make unexported functions static
ARM: OMAP: pdata-quirks: Remove unused timer pdata
pwm: pwm-omap-dmtimer: Adapt driver to utilize dmtimer pdata ops
clocksource: timer-ti-dm: Hook device platform data if not already assigned
clocksource: timer-ti-dm: Populate the timer ops to the pdata
clocksource: timer-ti-dm: Add timer ops to the platform data structure
ARM: OMAP: Move dmtimer driver out of plat-omap to drivers under clocksource
clocksource: timer-ti-dm: Replace architecture
ARM: OMAP: Move dmtimer.h out of plat-omap
ARM: OMAP: timer: Wrap the inline functions under OMAP2PLUS define
ARM: OMAP: dmtimer: Remove all the exports
ARM: OMAP: Fix dmtimer init for omap1
Pull "SoC changes for omaps for v4.17" from Tony Lindgren:
This series is mostly a series from Suman Anna to remove now unused
platform data that is now coming from device tree. This also make it
a bit simpler to move the timer code to live under drivers in a
separate series of patches. There are also few minor clean-ups for
omap4 PM code.
* tag 'omap-for-v4.17/soc-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix typo for wakeup_ns_pa_addr
ARM: OMAP2+: Use v7_invalidate_l1 in omap4_finish_suspend
ARM: OMAP2+: Remove unused gpio header file references
ARM: OMAP: Move plat/i2c.h into mach-omap1 folder
ARM: OMAP2+: Cleanup omap_mcbsp_dev_attr and other legacy data
ARM: OMAP2+: Cleanup omap2_spi_dev_attr and other legacy data
ARM: OMAP2+: Cleanup omap_timer_capability_dev_attr usage
ARM: OMAP2+: Cleanup omap_i2c_dev_attr usage
ARM: OMAP2+: Cleanup omap_gpio_dev_attr usage
ARM: OMAP2+: Include types.h directly for hwmod data
The "enable arbiter" bit is available only for pxa3xx based platforms
but it was experimentally shown that even if this bit is reserved,
some Marvell platforms (64-bit) actually need it to be set. The driver
always set this bit regardless of this property, which is harmless.
Then this property is not needed.
The "num_cs" field is always 1 and for a good reason, the old driver
(pxa3xx_nand.c) could only handle one. The new driver that replaces it
(marvell_nand.c) can handle more, but better use device tree for such
description. As there is only one available chip select, there is no
need for an array of partitions neither an array of partition numbers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Most of the PM code needed for am335x and am437x can be moved into a
module under drivers but some core code must remain in mach-omap2 at the
moment. This includes some internal clockdomain APIs and low-level ARM
APIs which are also not exported for use by modules.
Implement a few functions that handle these low-level platform
operations can be passed to the pm33xx module through the use of
platform data.
In addition to this, to be able to share data structures between C and
the sleep33xx and sleep43xx assembly code, we can automatically generate
all of the C struct member offsets and sizes as macros by processing
pm-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Finally, add amx3_common_pm_init to create a dummy platform_device for
pm33xx so that our soon to be introduced pm33xx module can probe on
am335x and am437x platforms to enable basic suspend to mem and standby
support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that ti-sysc can manage child devices, we must also be backwards
compatible with the current omap_device code. With omap_device, we
assume that the child device manages the interconnect target module
directly.
The drivers needing special handling are the ones that still set
pm_runtime_irq_safe(). In the long run we want to update those drivers
as otherwise they will cause problems with genpd as a permanent PM
runtime usage count is set on the parent device.
We can handle omap_device these devices by improving the ti-sysc quirk
handling to detect the devices needing special handling based on
register map and revision register if usable. We also need to implement
dev_pm_domain for these child devices just like omap_device does.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to pass the device tree configuration for interconnect target
modules from ti-sysc driver to the existing platform hwmod code.
This allows us to first validate the dts data against the existing
platform data before we start dropping the platform data in favor of
device tree data.
To do this, let's add platform data callbacks for PM runtime functions
to call for the interconnect target modules if platform data is
available.
Note that as ti-sysc driver can rebind, omap_auxdata_lookup and related
functions can no longer be __init.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This converts from using a platform device for the CFGCHIP syscon
regmap to using platform data to pass the regmap to consumers.
A lazy getter function is used so that the regmap will only be
created if it is actually used. This function will also be used
in the clock init when we convert to the common clock framework.
The USB PHY driver is currently the only consumer. This driver is
updated to use platform data to get the CFGCHIP regmap instead of
syscon_regmap_lookup_by_pdevname().
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The omap_mcbsp_dev_attr data was used to supply instance-specific
data for legacy non-DT devices. The legacy McBSP device support
including the usage of the hwmod class revision data has been
dropped in commit 48f6693790 ("ARM: OMAP2+: Remove unused legacy
code for McBSP") and this data is therefore no longer needed.
So, cleanup the structure and all the associated data in various
hwmod data files.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap2_spi_dev_attr data was used to supply instance-specific
data for legacy non-DT devices. The SPI legacy device support
including the usage of the hwmod class revision data has been
dropped in commit 6f3ab009a1 ("ARM: OMAP2+: Remove unused legacy
code for device init") and this data is therefore no longer needed.
So, cleanup the structure and all the associated data in various
hwmod data files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_gpio_dev_attr data was used to supply instance-specific
data for legacy non-DT devices. The GPIO legacy device support has
been cleaned up in commit 14944934f8 ("ARM: OMAP2+: Remove legacy
gpio code") a while ago and this data is therefore no longer needed.
So, cleanup the structure and all the associated data in various
hwmod data files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull x86 platform-driver updates from Darren Hart:
"New model support added for Dell, Ideapad, Acer, Asus, Thinkpad, and
GPD laptops. Improvements to the common intel-vbtn driver, including
tablet mode, rotate, and front button support. Intel CPU support added
for Cannonlake and platform support for Dollar Cove power button.
Overhaul of the mellanox platform driver, creating a new
platform/mellanox directory for the newly multi-architecture regmap
interface.
Significant Intel PMC update with CannonLake support, Coffeelake
update, CPUID enumeration, module support, new read64 API, refactoring
and cleanups.
Revert the apple-gmux iGP IO lock, addressing reported issues with
non-binary drivers, leaving Nvidia binary driver users to comment out
conflicting code.
Miscellaneous fixes and cleanups"
* tag 'platform-drivers-x86-v4.16-1' of git://git.infradead.org/linux-platform-drivers-x86: (81 commits)
platform/x86: mlx-platform: Fix an ERR_PTR vs NULL issue
platform/x86: intel_pmc_core: Special case for Coffeelake
platform/x86: intel_pmc_core: Add CannonLake PCH support
x86/cpu: Add Cannonlake to Intel family
platform/x86: intel_pmc_core: Read base address from LPIT
ACPI / LPIT: Export lpit_read_residency_count_address()
platform/x86: intel-vbtn: Replace License by SDPX identifier
platform/x86: intel-vbtn: Remove redundant inclusions
platform/x86: intel-vbtn: Support tablet mode switch
platform/x86: dell-laptop: Allocate buffer on heap rather than globally
platform/x86: intel_pmc_core: Remove unused header file
platform/x86: mlx-platform: Add hotplug device unregister to error path
platform/x86: mlx-platform: fix module aliases
platform/mellanox: mlxreg-hotplug: Add check for negative adapter number
platform/x86: mlx-platform: Add IO access verification callbacks
platform/x86: mlx-platform: Document pdev_hotplug field
platform/x86: mlx-platform: Allow compilation for 32 bit arch
platform/mellanox: mlxreg-hotplug: Enable building for ARM
platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface
platform/mellanox: Group create/destroy with attribute functions
...
Pull i2c updates from Wolfram Sang:
"I2C has the following changes for you:
- new flag to mark DMA safe buffers in i2c_msg. Also, some
infrastructure around it. And docs.
- huge refactoring of the at24 driver led by the new maintainer
Bartosz
- update I2C bus recovery to send STOP after recovery
- conversion from gpio to gpiod for I2C bus recovery
- adding a fault-injector to the i2c-gpio driver
- lots of small driver improvements, and bigger ones to
i2c-sh_mobile"
* 'i2c/for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (99 commits)
i2c: mv64xxx: Add myself as maintainer for this driver
i2c: mv64xxx: Fix clock resource by adding an optional bus clock
i2c: mv64xxx: Remove useless test before clk_disable_unprepare
i2c: mxs: use true and false for boolean values
i2c: meson: update doc description to fix build warnings
i2c: meson: add configurable divider factors
dt-bindings: i2c: update documentation for the Meson-AXG
i2c: imx-lpi2c: add runtime pm support
i2c: rcar: fix some trivial typos in comments
i2c: davinci: fix the cpufreq transition
i2c: rk3x: add proper kerneldoc header
i2c: rk3x: account for const type of of_device_id.data
i2c: acorn: remove outdated path from file header
i2c: acorn: add MODULE_LICENSE tag
i2c: rcar: implement bus recovery
i2c: send STOP after successful bus recovery
i2c: ensure SDA is released in recovery if SDA is controllable
i2c: add 'set_sda' to bus_recovery_info
i2c: add identifier in declarations for i2c_bus_recovery
i2c: make kerneldoc about bus recovery more precise
...
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
Pull ARM SoC platform updates from Arnd Bergmann:
"These are mostly minor bugfixes, cleanup and many defconfig updates to
support added drivers. In particular OMAP and PXA keep cleaning up the
legacy code base, as usual.
Nvidia adds some more SoC support code for Tegra 186.
For the first time on years, we are actually adding a non-DT platform
for the EP93xx based Liebherr controller BK3.1. It's a minor variation
of the EP93xx reference design and in active use, while EP93xx
apparently doesn't have enough new development to have any device tree
support"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: omap: hwmod: fix section mismatch warnings
ARM: pxa/tosa-bt: add MODULE_LICENSE tag
arm64: defconfig: enable CONFIG_ACPI_APEI_EINJ
arm64: defconfig: enable EDAC GHES option
arm64: defconfig: enable CONFIG_ACPI_APEI_MEMORY_FAILURE
ARM: imx_v6_v7_defconfig: enable CONFIG_CPU_FREQ_STAT
Wind down ARM/TANGO port
ARM: davinci: constify gpio_led
ARM: davinci: drop unneeded newline
soc: Add SoC driver for Gemini
ARM: SAMSUNG: Add SPDX license identifiers
ARM: S5PV210: Add SPDX license identifiers
ARM: S3C64XX: Add SPDX license identifiers
ARM: S3C24XX: Add SPDX license identifiers
ARM: EXYNOS: Add SPDX license identifiers
ARM: imx: remove unused imx3 pm definitions
ARM: imx: don't abort MMDC probe if power saving status doesn't match
ARM: imx_v6_v7_defconfig: enable RTC_DRV_MXC_V2
ARM: imx_v6_v7_defconfig: Add missing config for DART-MX6 SoM
ARM: davinci: Use PTR_ERR_OR_ZERO()
...
Pull input layer updates from Dmitry Torokhov:
- evdev interface has been adjusted to extend the life of timestamps on
32 bit systems to the year of 2108
- Synaptics RMI4 driver's PS/2 guest handling ha beed updated to
improve chances of detecting trackpoints on the pass-through port
- mms114 touchcsreen controller driver has been updated to support
generic device properties and work with mms152 cntrollers
- Goodix driver now supports generic touchscreen properties
- couple of drivers for AVR32 architecture are gone as the architecture
support has been removed from the kernel
- gpio-tilt driver has been removed as there are no mainline users and
the driver itself is using legacy APIs and relies on platform data
- MODULE_LINECSE/MODULE_VERSION cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: goodix - use generic touchscreen_properties
Input: mms114 - fix typo in definition
Input: mms114 - use BIT() macro instead of explicit shifting
Input: mms114 - replace mdelay with msleep
Input: mms114 - add support for mms152
Input: mms114 - drop platform data and use generic APIs
Input: mms114 - mark as direct input device
Input: mms114 - do not clobber interrupt trigger
Input: edt-ft5x06 - fix error handling for factory mode on non-M06
Input: stmfts - set IRQ_NOAUTOEN to the irq flag
Input: auo-pixcir-ts - delete an unnecessary return statement
Input: auo-pixcir-ts - remove custom log for a failed memory allocation
Input: da9052_tsi - remove unused mutex
Input: docs - use PROPERTY_ENTRY_U32() directly
Input: synaptics-rmi4 - log when we create a guest serio port
Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
Input: synaptics-rmi4 - do not delete interrupt memory too early
Input: ad7877 - use managed resource allocations
Input: stmfts,s6sy671 - add SPDX identifier
Input: remove atmel-wm97xx touchscreen driver
...
Restructure mlxreg header for unification of hotplug item definitions.
Unify hotplug items to allow any kind of item (power controller, fan
eeprom, psu eeprom, asic health) in common way.
Use a hardware independent regmap interface, enabling the support of
hotplug events over programmable devices attached to different bus
types, such as I2C, LPC, or SPI. Add a device node to the
mlxreg_core_data structure.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: spelling corrections, refactor device node introduction]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use Linux convention of nr instead of bus for i2c adapter number.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: refactored commit into smaller functional changes]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In preparation for making the hotplug driver build for different
architectures, move mlxcpld-hotplug.c to platform/mellanox and the
header to include/linux/platform_data as mlxreg.h to reflect the new
interface changes to come.
Replace references to CPLD with REG throughout the files, consistent
with the new name.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[dvhart: update copyright, rewrite commit message]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Pull spi updates from Mark Brown:
"Quite a quiet release for SPI, there are no changes at all to the core
and not that many changes to drivers. Highlights of those driver
changes include:
- SH MSIOF support for GPIO chip selects contributed by Geert
Uytterhoeven.
- Full duplex support for a3700 contributed by Maxime Chevallier.
- Support for DMA transfers on Atmel devices that require a bounce
buffer contributed by Radu Pirea"
* tag 'spi-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (31 commits)
spi: dw: Remove unused members from struct chip_data
spi: orion: Fix a resource leak if the optional "axi" clk is deferred
spi: a3700: Remove endianness swapping for full-duplex transfers
spi: a3700: Remove endianness swapping functions when accessing FIFOs
spi: a3700: Add full-duplex support
spi: a3700: Allow to enable or disable FIFO mode
spi: a3700: Set frequency limits at startup
spi: a3700: Clear DATA_OUT when performing a read
spi: orion: Fix clock resource by adding an optional bus clock
spi: s3c64xx: add SPDX identifier
spi: imx: do not access registers while clocks disabled
spi: atmel: Implements transfers with bounce buffer
spi: sh-msiof: Fix timeout failures for TX-only DMA transfers
spi: spi-fsl-dspi: account for const type of of_device_id.data
spi: bcm53xx: simplify reading SPI data
spi: sirf: account for const type of of_device_id.data
spi: pxa2xx: Use gpiod_put() not gpiod_free()
spi: pxa2xx: avoid redundant gpio_to_desc(desc_to_gpio()) round-trip
spi: sh-msiof: Document hardware limitations related to chip selects
spi: sh-msiof: Implement cs-gpios configuration
...
The MMS114 platform data has no in-tree users, so drop it.
Switch to using the standard touchscreen properties via
touchscreen_parse_properties(), and move the old DT parsing code
to use device_property_*() APIs.
Finally, use touchscreen_report_pos to report x/y coordinates
and drop the custom x/y inversion code.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
"AT24 updates for 4.16 merge window
The driver has been converted to using regmap instead of raw i2c and
smbus calls which shrank the code significantly.
Device tree binding document has been cleaned up. Device tree support in
the driver has been improved and we now support all at24 models as well
as two new DT properties (no-read-rollover and wp-gpios).
We no longer user unreadable magic values for driver data as the way it
was implemented caused problems for some EEPROM models - we switched to
regular structs.
Aside from that, there's a bunch of coding style fixes and minor
improvements all over the place."
Replace spaces with tabs in the definition of AT24_FLAG_NO_RDROL.
Fixes: 9d404411091c ("eeprom: at24: support eeproms that do not auto-rollover reads")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Some multi-address eeproms in the at24 family may not automatically
roll-over reads to the next slave address. On those eeproms, reads
that straddle slave boundaries will not work correctly.
Solution:
Mark such eeproms with a flag that prevents reads straddling
slave boundaries. Add the AT24_FLAG_NO_RDROL flag to the eeprom
entry in the device_id table, or add 'no-read-rollover' to the
eeprom devicetree entry.
Note that I have not personally enountered an at24 chip that
does not support read rollovers. They may or may not exist.
However, my hardware requires this functionality because of
a quirk.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
We need to configure the interconnect target module based on the
device three configuration.
Let's also add a new quirk for SYSC_QUIRK_RESET_STATUS to indicate
that the SYSCONFIG reset bit changes after the reset is done.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's configure few module quirks via device tree using the
properties for "ti,no-idle-on-init", "ti,no-reset-on-init"
and "ti,sysc-delay-us".
Let's also reorder the probe a bit so we have pdata available
earlier, and move the PM runtime calls to sysc_init_module()
from sysc_read_revision().
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can easily detect i2c based on it's non-standard module registers that
consist of two 32-bit registers accessed in 16-bit mode.
So far we don't have other 16-bit modules, so there's currently no need
to add a custom property for 16-bit register access.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add data for the known interconnect target module types by mapping
their register bits.
Note that we can handle many quirks for the older omap2 type1 modules
directly in the driver without a need for adding custom properties.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to be able to configure hwmod sysc data from ti-sysc driver using
platform data callbacks. So let's make struct omap_hwmod_sysc_fields into
struct sysc_data and have it available for both ti-sysc driver and hwmod
code.
Note that we can make it use s8 instead of u8 as the hwmod code uses the
feature flags to check for this field. However, for ti-sysc we can use
-ENODEV to indicate a feature is not supported in the hardware and can
simplify the code that way.
And let's add also emufree_shift as the dts files will be describing the
hardware for the SYSCONFIG register capbilities mask.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
include/linux/i2c is to be deprecated. Move this platform_data to the
proper platform_data dir.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
S6SY761
- the timer API conversion (setup_timer() -> timer_setup())
- a few drivers swiytched to using managed API for creating custom
device attributes
- other assorted fixed and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: gamecon - mark expected switch fall-throughs
Input: sidewinder - mark expected switch fall-throughs
Input: spaceball - mark expected switch fall-throughs
Input: uinput - unlock on allocation failure in ioctl
Input: add support for the Samsung S6SY761 touchscreen
Input: add support for HiDeep touchscreen
Input: st1232 - remove obsolete platform device support
Input: convert autorepeat timer to use timer_setup()
media: ttpci: remove autorepeat handling and use timer_setup
Input: cyttsp4 - avoid overflows when calculating memory sizes
Input: mxs-lradc - remove redundant assignment to pointer input
Input: add I2C attached EETI EXC3000 multi touch driver
Input: goodix - support gt1151 touchpanel
Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
Input: hil_mlc - convert to using timer_setup()
Input: hp_sdc - convert to using timer_setup()
Input: touchsceen - convert timers to use timer_setup()
Input: keyboard - convert timers to use timer_setup()
Input: uinput - fold header into the driver proper
Input: uinput - remove uinput_allocate_device()
...
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
Pull hwmon updates from Guenter Roeck:
- drivers for MAX31785 and MAX6621
- support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- various driver cleanups and minor improvements
* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
dt-bindings: pmbus: Add Maxim MAX31785 documentation
pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
hwmon: (aspeed-pwm-tacho) Sort headers
hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
hwmon: (max6621) Inverted if condition in max6621_read()
hwmon: (asc7621) remove redundant assignment to newval
hwmon: (xgene) Support hwmon v2
hwmon: (gpio-fan) Fix null pointer dereference at probe
hwmon: (gpio-fan) Convert to use GPIO descriptors
hwmon: (gpio-fan) Rename GPIO line state variables
hwmon: (gpio-fan) Get rid of the gpio alarm struct
hwmon: (gpio-fan) Get rid of platform data struct
hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
hwmon: (gpio-fan) Send around device pointer
hwmon: (gpio-fan) Localize platform data
hwmon: (gpio-fan) Use local variable pointers
hwmon: (gpio-fan) Move DT bindings to the right place
Documentation: devicetree: add max6621 device
hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
hwmon: (w83793) make const array watchdog_minors static, reduces object code size
...
Commit 1fa59bda21 ("ARM: shmobile: Remove legacy board code for
Armadillo-800 EVA"), removed the last user of st1232_pdata and the
"st1232-ts" platform device. All remaining users use DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
