[ Upstream commit bd4d607044b961cecbf8c4c2f3bb5da4fb156993 ]
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7f755b243494d6043aadcd9a2989cb157958b95 ]
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-4-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 755915fc28edfc608fa89a163014acb2f31c1e19 ]
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbdbbe6d3ee502b3bdeb4f255196bb45003614be ]
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91356fed6afd1c83bf0d3df1fc336d54e38f0458 ]
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 50a318cc9b54a36f00beadf77e578a50f3620477 upstream.
The commit d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a121 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a5d797a9f9c4f18585544237216d7812686a71f upstream.
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a932ee40c276767cd55fadec9e38829bf441db41 ]
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 72035f4954f0bca2d8c47cf31b3629c42116f5b7 upstream.
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6aa61d81194c01283880950df563b1b9abec46 upstream.
Commit c318840fb2a4 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds
bug") messed up the way dummy-hcd handles requests to turn on the
RESET port feature (I didn't notice that the original switch case
ended with a fallthrough). The call to set_link_state() was
inadvertently removed, as was the code to set the USB_PORT_STAT_RESET
flag when the speed is USB2.
In addition, the original code never checked whether the port was
connected before handling the port-reset request. There was a check
for the port being powered, but it was removed by that commit! In
practice this doesn't matter much because the kernel doesn't try to
reset disconnected ports, but it's still bad form.
This patch fixes these problems by changing the fallthrough to break,
adding back in the missing set_link_state() call, setting the
port-reset status flag, adding a port-is-connected test, and removing
a redundant assignment statement.
Fixes: c318840fb2a4 ("USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug")
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20210113194510.GA1290698@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c318840fb2a42ce25febc95c4c19357acf1ae5ca upstream.
The dummy-hcd driver was written under the assumption that all the
parameters in URBs sent to its root hub would be valid. With URBs
sent from userspace via usbfs, that assumption can be violated.
In particular, the driver doesn't fully check the port-feature values
stored in the wValue entry of Clear-Port-Feature and Set-Port-Feature
requests. Values that are too large can cause the driver to perform
an invalid left shift of more than 32 bits. Ironically, two of those
left shifts are unnecessary, because they implement Set-Port-Feature
requests that hubs are not required to support, according to section
11.24.2.13 of the USB-2.0 spec.
This patch adds the appropriate checks for the port feature selector
values and removes the unnecessary feature settings. It also rejects
requests to set the TEST feature or to set or clear the INDICATOR and
C_OVERCURRENT features, as none of these are relevant to dummy-hcd's
root-hub emulation.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+5925509f78293baa7331@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20201230162044.GA727759@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl_ep_fifo_status() should return error if _ep->desc is null.
Fixes: 75eaa498c9 (“usb: gadget: Correct NULL pointer checking in fsl gadget”)
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
goku_probe() goes to error label "err" and invokes goku_remove()
in case of failures of pci_enable_device(), pci_resource_start()
and ioremap(). goku_remove() gets a device from
pci_get_drvdata(pdev) and works with it without any checks, in
particular it dereferences a corresponding pointer. But
goku_probe() did not set this device yet. So, one can expect
various crashes. The patch moves setting the device just after
allocation of memory for it.
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
in case devm_platform_ioremap_resource() fails, that function already
prints a relevant error message which renders the driver's dev_err()
redundant. Let's remove the unnecessary message and, while at that,
also make sure to pass along the error value returned by
devm_platform_ioremap_resource() instead of always returning -ENOMEM.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
[balbi@kernel.org : improved commit log]
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Probe deferral is an expected condition and can happen multiple times
during boot. Make sure not to output an error message in that case
because they are not useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Align parameters on subsequent lines with the parameters on the first
line for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make sure to use consistent spelling and formatting in error messages.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Current UDC core connects gadget during the loading gadget flow
(udc_bind_to_driver->usb_udc_connect_control), but for
platforms which do not connect gadget if the VBUS is not there,
they call usb_gadget_disconnect, but the gadget is not connected
at this time, notify disconnecton for the gadget driver is meaningless
at this situation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove unused 'udc' variable to fix compile warnings:
drivers/usb/gadget/udc/s3c2410_udc.c: In function 's3c2410_udc_dequeue':
drivers/usb/gadget/udc/s3c2410_udc.c:1268:22: warning: variable 'udc' set but not used [-Wunused-but-set-variable]
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Like net2280 (on which it was based), the net2272 UDC driver has a
problem with leaking memory along some of its failure pathways. It
also has another problem, not previously noted, in that some of the
failure pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Until now it has been impossible to handle the memory leaks, because of
lack of support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. An earlier
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2272 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate places.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As Anton and Evgeny have noted, the net2280 UDC driver has a problem
with leaking memory along some of its failure pathways. It also has
another problem, not previously noted, in that some of the failure
pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Previous attempts to fix the problems have failed because of lack of
support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. The previous
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2280 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate point.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anton Vasilyev <vasilyev@ispras.ru>
Reported-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The routines used by the UDC core to interface with the kernel's
device model, namely usb_add_gadget_udc(),
usb_add_gadget_udc_release(), and usb_del_gadget_udc(), provide access
to only a subset of the device model's full API. They include
functionality equivalent to device_register() and device_unregister()
for gadgets, but they omit device_initialize(), device_add(),
device_del(), get_device(), and put_device().
This patch expands the UDC API by adding usb_initialize_gadget(),
usb_add_gadget(), usb_del_gadget(), usb_get_gadget(), and
usb_put_gadget() to fill in the gap. It rewrites the existing
routines to call the new ones.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
udc_controller->irq is "unsigned int" always >= 0, but platform_get_irq may
return little than zero. So "dc_controller->irq < 0" condition is never
accessible.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This switches the PCH UDC driver to use GPIO descriptors. The way
this is supposed to be used is confusing. The code contains the
following:
/* GPIO port for VBUS detecting */
static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */
So a hardcoded GPIO number in the code. Further the probe() path
very clearly will exit if the GPIO is not found, so this driver
can only be configured by editing the code, hard-coding a GPIO
number into this variable.
This is simply not how we do things. My guess is that this is
used in products by patching a GPIO number into this variable and
shipping a kernel that is compile-time tailored for the target
system.
I switched this mechanism to using a GPIO descriptor associated
with the parent PCI device. This can be added by using the 16bit
subsystem ID or similar to identify which exact machine we are
running on and what GPIO is present on that machine, and then
add a GPIO descriptor using gpiod_add_lookup_table() from
<linux/gpio/machine.h>. Since I don't have any target systems
I cannot add this but I'm happy to help. I put in a FIXME so
the people actually using this driver knows what to do.
Cc: Felipe Balbi <balbi@kernel.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This is a follow-on patch for commit a23be4ed8f ("usb: gadget: aspeed:
improve vhub port irq handling"): for_each_set_bit() is replaced with
simple for() loop because for() loop runs faster on ASPEED BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
