[ Upstream commit 2b2bfc8aa519f696087475ed8e8c61850c673272 ]
Some SoCs require a single scatterlist entry for smaller than page size,
i.e. 4KB. When dispatching commands with more than one scatterlist entry
under 4KB in size the following behavior is observed:
A command to read a block range is dispatched with two scatterlist entries
that are named AAA and BBB. After dispatching, the host builds two PRDT
entries and during transmission, device sends just one DATA IN because
device doesn't care about host DMA. The host then transfers the combined
amount of data from start address of the area named AAA. As a consequence,
the area that follows AAA in memory would be corrupted.
|<------------->|
+-------+------------ +-------+
+ AAA + (corrupted) ... + BBB +
+-------+------------ +-------+
To avoid this we need to enforce page size alignment for sg entries.
Link: https://lore.kernel.org/r/56dddef94f60bd9466fd77e69f64bbbd657ed2a1.1611026909.git.kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1d0d2eb89d4e3a25b212a9d836587503537067e ]
The UniPro specification states that attribute IDs of the following
parameters are vendor-specific so some SoCs could have no regions at the
defined addresses:
- DME_LocalFC0ProtectionTimeOutVal
- DME_LocalTC0ReplayTimeOutVal
- DME_LocalAFC0ReqTimeOutVal
In addition, the following parameters should be set considering the
compatibility between host and device.
- PA_PWRMODEUSERDATA0
- PA_PWRMODEUSERDATA1
- PA_PWRMODEUSERDATA2
- PA_PWRMODEUSERDATA3
- PA_PWRMODEUSERDATA4
- PA_PWRMODEUSERDATA5
Introduce a quirk to allow vendor drivers to override the UniPro defaults.
Link: https://lore.kernel.org/r/1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.com
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9dbdf97a5bd92b1a49cee3d591b55b11fd7a6d5 upstream.
Open-iSCSI sends passthrough PDUs over netlink, but the kernel should be
verifying that the provided PDU header and data lengths fall within the
netlink message to prevent accessing beyond that in memory.
Cc: stable@vger.kernel.org
Reported-by: Adam Nichols <adam@grimm-co.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec98ea7070e94cc25a422ec97d1421e28d97b7ee upstream.
As the iSCSI parameters are exported back through sysfs, it should be
enforcing that they never are more than PAGE_SIZE (which should be more
than enough) before accepting updates through netlink.
Change all iSCSI sysfs attributes to use sysfs_emit().
Cc: stable@vger.kernel.org
Reported-by: Adam Nichols <adam@grimm-co.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 688e8128b7a92df982709a4137ea4588d16f24aa upstream.
Protect the iSCSI transport handle, available in sysfs, by requiring
CAP_SYS_ADMIN to read it. Also protect the netlink socket by restricting
reception of messages to ones sent with CAP_SYS_ADMIN. This disables
normal users from being able to end arbitrary iSCSI sessions.
Cc: stable@vger.kernel.org
Reported-by: Adam Nichols <adam@grimm-co.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c65830ae1629b03e5d65e9aafae7e2cf5f8b743 ]
In testing, in a configuration with Redfish and native NVMe multipath when
an EEH is injected, a kernel oops is being encountered:
(unreliable)
lpfc_nvme_ls_req+0x328/0x720 [lpfc]
__nvme_fc_send_ls_req.constprop.13+0x1d8/0x3d0 [nvme_fc]
nvme_fc_create_association+0x224/0xd10 [nvme_fc]
nvme_fc_reset_ctrl_work+0x110/0x154 [nvme_fc]
process_one_work+0x304/0x5d
the NBMe transport is issuing a Disconnect LS request, which the driver
receives and tries to post but the work queue used by the driver is already
being torn down by the eeh.
Fix by validating the validity of the work queue before proceeding with the
LS transmit.
Link: https://lore.kernel.org/r/20210127221601.84878-1-jsmart2021@gmail.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 764907293edc1af7ac857389af9dc858944f53dc ]
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b0f16fa65e910a3ec8771206bb49ee87a54ac5 ]
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Link: https://lore.kernel.org/r/20201215194731.2326-1-jhasan@marvell.com
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb1b55b6e25c5f7265ff45cd050f3bc2cc423a4 ]
When non-fatal error like line-reset happens, ufshcd_err_handler() starts
to abort tasks by ufshcd_try_to_abort_task(). When it tries to issue a task
management request, we hit two warnings:
WARNING: CPU: 7 PID: 7 at block/blk-core.c:630 blk_get_request+0x68/0x70
WARNING: CPU: 4 PID: 157 at block/blk-mq-tag.c:82 blk_mq_get_tag+0x438/0x46c
After fixing the above warnings we hit another tm_cmd timeout which may be
caused by unstable controller state:
__ufshcd_issue_tm_cmd: task management cmd 0x80 timed-out
Then, ufshcd_err_handler() enters full reset, and kernel gets stuck. It
turned out ufshcd_print_trs() printed too many messages on console which
requires CPU locks. Likewise hba->silence_err_logs, we need to avoid too
verbose messages. This is actually not an error case.
Link: https://lore.kernel.org/r/20210107185316.788815-3-jaegeuk@kernel.org
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b112036535eda34460677ea883eaecc3a45a435d ]
Phil Oester reported that a fix for a possible buffer overrun that I sent
caused a regression that manifests in this output:
Event Message: A PCI parity error was detected on a component at bus 0 device 5 function 0.
Severity: Critical
Message ID: PCI1308
The original code tried to handle the sense data pointer differently when
using 32-bit 64-bit DMA addressing, which would lead to a 32-bit dma_addr_t
value of 0x11223344 to get stored
32-bit kernel: 44 33 22 11 ?? ?? ?? ??
64-bit LE kernel: 44 33 22 11 00 00 00 00
64-bit BE kernel: 00 00 00 00 44 33 22 11
or a 64-bit dma_addr_t value of 0x1122334455667788 to get stored as
32-bit kernel: 88 77 66 55 ?? ?? ?? ??
64-bit kernel: 88 77 66 55 44 33 22 11
In my patch, I tried to ensure that the same value is used on both 32-bit
and 64-bit kernels, and picked what seemed to be the most sensible
combination, storing 32-bit addresses in the first four bytes (as 32-bit
kernels already did), and 64-bit addresses in eight consecutive bytes (as
64-bit kernels already did), but evidently this was incorrect.
Always storing the dma_addr_t pointer as 64-bit little-endian,
i.e. initializing the second four bytes to zero in case of 32-bit
addressing, apparently solved the problem for Phil, and is consistent with
what all 64-bit little-endian machines did before.
I also checked in the history that in previous versions of the code, the
pointer was always in the first four bytes without padding, and that
previous attempts to fix 64-bit user space, big-endian architectures and
64-bit DMA were clearly flawed and seem to have introduced made this worse.
Link: https://lore.kernel.org/r/20210104234137.438275-1-arnd@kernel.org
Fixes: 381d34e376e3 ("scsi: megaraid_sas: Check user-provided offsets")
Fixes: 107a60dd71 ("scsi: megaraid_sas: Add support for 64bit consistent DMA")
Fixes: 94cd65ddf4 ("[SCSI] megaraid_sas: addded support for big endian architecture")
Fixes: 7b2519afa1 ("[SCSI] megaraid_sas: fix 64 bit sense pointer truncation")
Reported-by: Phil Oester <kernel@linuxace.com>
Tested-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5cc9002caafacbaa8dab878d17a313192c3b03b ]
The block layer code will split a large zeroout request into multiple bios
and if WRITE SAME is disabled because the storage device reports that it
does not support it (or support the length used), we can get an error
message from the block layer despite the setting of RQF_QUIET on the first
request. This is because more than one request may have already been
submitted.
Fix this by setting RQF_QUIET when BLK_STS_TARGET is returned to fail the
request early, we don't need to log a message because we did not actually
submit the command to the device, and the block layer code will handle the
error by submitting individual write bios.
Link: https://lore.kernel.org/r/20201207221021.28243-1-emilne@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35fc4cd34426c242ab015ef280853b7bff101f48 ]
Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.
Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d53864c3617f5235f891ca0fbe9347c4cd35d46 upstream.
Currently if device needs to do flush or BKOP operations, the device VCC
power is kept during runtime-suspend period.
However, if system suspend is happening while device is runtime-suspended,
such power may not be disabled successfully.
The reasons may be,
1. If current PM level is the same as SPM level, device will keep
runtime-suspended by ufshcd_system_suspend().
2. Flush recheck work may not be scheduled successfully during system
suspend period. If it can wake up the system, this is also not the
intention of the recheck work.
To fix this issue, simply runtime-resume the device if the flush is allowed
during runtime suspend period. Flush capability will be disabled while
leaving runtime suspend, and also not be allowed in system suspend period.
Link: https://lore.kernel.org/r/20201222072905.32221-2-stanley.chu@mediatek.com
Fixes: 51dd905bd2 ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c60244dc37262023d24b167e245055c06bc0b77 ]
clang complains about a possible code path in which a variable is used
without an initialization:
drivers/scsi/ufs/ufshcd.c:7690:3: error: variable 'sdp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:63:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
Turn the BUG_ON(1) into an unconditional BUG() that makes it clear to clang
that this code path is never hit.
Link: https://lore.kernel.org/r/20201203223137.1205933-1-arnd@kernel.org
Fixes: 4f3e900b6282 ("scsi: ufs: Clear UAC for FFU and RPMB LUNs")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c763729a10e538d997744317cf4a1c4f25266066 ]
Currently, ufshcd-pci is the only UFS driver with support for
suspend-to-disk PM callbacks (i.e. freeze/thaw/restore/poweroff). These
callbacks are set by the macro SET_SYSTEM_SLEEP_PM_OPS to the same
functions as system suspend/resume. That will work with spm_lvl 5 because
spm_lvl 5 will result in a full restore for the ->restore() callback. In
the absence of a full restore, the host controller registers will have
values set up by the restore kernel (the kernel that boots and loads the
restore image) which are not necessarily the same. However it turns out,
the only registers that sometimes need restore are the base address
registers. This has gone un-noticed because, depending on IOMMU settings,
the kernel can end up allocating the same addresses every time.
For Intel controllers, an spm_lvl other than 5 can be used, so to support
S4 (suspend-to-disk) with spm_lvl other than 5, restore the base address
registers.
Link: https://lore.kernel.org/r/20201207083120.26732-2-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd14bf0e4a084514aa62d24d2109e0f09a93822f ]
UFS 3.1 specification mentions that the WriteBooster flags listed below
will be set to their default values, i.e. disabled, after power cycle or
any type of reset event. Thus we need to reset the flag variables kept in
struct hba to align with the device status and ensure that
WriteBooster-related functions are configured properly after device reset.
Without this fix, WriteBooster will not be enabled successfully after by
ufshcd_wb_ctrl() after device reset because hba->wb_enabled remains true.
Flags required to be reset to default values:
- fWriteBoosterEn: hba->wb_enabled
- fWriteBoosterBufferFlushEn: hba->wb_buf_flush_enabled
- fWriteBoosterBufferFlushDuringHibernate: No variable mapped
Link: https://lore.kernel.org/r/20201208135635.15326-2-stanley.chu@mediatek.com
Fixes: 3d17b9b5ab ("scsi: ufs: Add write booster feature support")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e7dab164a9aa457f89d4528452bdfc3e15ac98b6 upstream.
The following call trace was seen during HBA reset testing:
BUG: scheduling while atomic: swapper/2/0/0x10000100
...
Call Trace:
dump_stack+0x19/0x1b
__schedule_bug+0x64/0x72
__schedule+0x782/0x840
__cond_resched+0x26/0x30
_cond_resched+0x3a/0x50
mempool_alloc+0xa0/0x170
lpfc_unreg_rpi+0x151/0x630 [lpfc]
lpfc_sli_abts_recover_port+0x171/0x190 [lpfc]
lpfc_sli4_abts_err_handler+0xb2/0x1f0 [lpfc]
lpfc_sli4_io_xri_aborted+0x256/0x300 [lpfc]
lpfc_sli4_sp_handle_abort_xri_wcqe.isra.51+0xa3/0x190 [lpfc]
lpfc_sli4_fp_handle_cqe+0x89/0x4d0 [lpfc]
__lpfc_sli4_process_cq+0xdb/0x2e0 [lpfc]
__lpfc_sli4_hba_process_cq+0x41/0x100 [lpfc]
lpfc_cq_poll_hdler+0x1a/0x30 [lpfc]
irq_poll_softirq+0xc7/0x100
__do_softirq+0xf5/0x280
call_softirq+0x1c/0x30
do_softirq+0x65/0xa0
irq_exit+0x105/0x110
do_IRQ+0x56/0xf0
common_interrupt+0x16a/0x16a
With the conversion to blk_io_poll for better interrupt latency in normal
cases, it introduced this code path, executed when I/O aborts or logouts
are seen, which attempts to allocate memory for a mailbox command to be
issued. The allocation is GFP_KERNEL, thus it could attempt to sleep.
Fix by creating a work element that performs the event handling for the
remote port. This will have the mailbox commands and other items performed
in the work element, not the irq. A much better method as the "irq" routine
does not stall while performing all this deep handling code.
Ensure that allocation failures are handled and send LOGO on failure.
Additionally, enlarge the mailbox memory pool to reduce the possibility of
additional allocation in this path.
Link: https://lore.kernel.org/r/20201020202719.54726-3-james.smart@broadcom.com
Fixes: 317aeb83c9 ("scsi: lpfc: Add blk_io_poll support for latency improvment")
Cc: <stable@vger.kernel.org> # v5.9+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e3a931db60daf94fdb3159d685a5bc6ad4d0cf upstream.
The following calltrace was seen:
BUG: sleeping function called from invalid context at mm/slab.h:494
...
Call Trace:
dump_stack+0x9a/0xf0
___might_sleep.cold.63+0x13d/0x178
slab_pre_alloc_hook+0x6a/0x90
kmem_cache_alloc_trace+0x3a/0x2d0
lpfc_sli4_nvmet_alloc+0x4c/0x280 [lpfc]
lpfc_post_rq_buffer+0x2e7/0xa60 [lpfc]
lpfc_sli4_hba_setup+0x6b4c/0xa4b0 [lpfc]
lpfc_pci_probe_one_s4.isra.15+0x14f8/0x2280 [lpfc]
lpfc_pci_probe_one+0x260/0x2880 [lpfc]
local_pci_probe+0xd4/0x180
work_for_cpu_fn+0x51/0xa0
process_one_work+0x8f0/0x17b0
worker_thread+0x536/0xb50
kthread+0x30c/0x3d0
ret_from_fork+0x3a/0x50
A prior patch introduced a spin_lock_irqsave(hbalock) in the
lpfc_post_rq_buffer() routine. Call trace is seen as the hbalock is held
with interrupts disabled during a GFP_KERNEL allocation in
lpfc_sli4_nvmet_alloc().
Fix by reordering locking so that hbalock not held when calling
sli4_nvmet_alloc() (aka rqb_buf_list()).
Link: https://lore.kernel.org/r/20201020202719.54726-2-james.smart@broadcom.com
Fixes: 411de511c6 ("scsi: lpfc: Fix RQ empty firmware trap")
Cc: <stable@vger.kernel.org> # v4.17+
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
