WMI command reply saved in uninitialized struct.
In order to avoid accessing unset values from FW initialize
the reply struct.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having new function wmi_mgmt_tx() to take care
of the WMI part of wil_cfg80211_mgmt_tx().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change the type of the argument reply_size from u8 to
u16 in order to support reply sizes > 255 bytes.
The driver already supports u16 reply size in all
other places, this was the only missing change.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move the call to wil6210_disconnect so it will be called
before unregister_netdevice. This is because it calls
netif_carrier_off which is forbidden to call on an
unregistered net device. Calling netif_carrier_off can
add a link watch event which might be handled after
net device was freed, causing a kernel oops.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the BIT() macro from 'linux/bitops.h' to define the rx desc
bit flags to have consistency with new definitions.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason not all entries used ATH10K_FW_DIR so fix that. No functional
changes.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buf_len and num_vdev_stats are being assigned but never read.
These are redundant and can be remove.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_tx_push_txq returns either a postive integer (length) on
success or a negative error code on error.
The "if (ret) break;" statement will thus always break out of the loop
immediately after ath10k_mac_tx_push_txq has returned (making the loop
pointless).
A side effect of this fix is that we will iterate the queue until
ath10k_mac_tx_push_txq returns -ENOENT. This will make sure the queue is
not added back to ar->txqs when it is empty. This could potentially
improve performance somewhat (I have seen a small improvement with SDIO
devices).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To enable thermal throttling for QCA6174 and QCA9377,
implement gen_pdev_set_quiet_mode for them.
With this change, quiet period for QCA6174/QCA9377 can
be also set/get via debugfs.
Usage:
To set quiet period:
echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
To get the current quiet period:
cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period
This change has been verified with
QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a usleep_range in mt76x2_mac_stop routine in order to add
a polling delay checking values of MT_MAC_STATUS and IBI_R12 registers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the addition of the TXQ stats to cfg80211, the station_info struct
has grown to be quite large, which results in warnings when allocated on
the stack. Fix the affected places to do dynamic allocations instead.
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Johannes Berg says:
====================
We only have a few fixes this time:
* WMM element validation
* SAE timeout
* add-BA timeout
* docbook parsing
* a few memory leaks in error paths
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While carrying energy detection(ED) tests, the chip will stop
transmission upon detecting an energy in the connected channel.
As a feedback, driver will stop dequeuing TX packets and due to
which wmm_tx_pending keep incremeting. Once wmm_tx_pending
reaches 100, driver calls netif_tx_stop_queue(). If TX ques is
not restarted within 5(watchdog_timeo) seconds, it will result in
TX timeout.
The ED test is carried out for one minute and the current
threshold of 100 is easily overcome by the traffic, cuasing TX
timeouts. To fix this increase the threshold to 400.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Nothing that is defined in 11ac.h is referenced in cmdevt.c.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one
can be removed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'hwname' should be freed before leaving from the error handling cases,
otherwise it will cause mem leak
Fixes: cb1a5bae56 ("mac80211_hwsim: add permanent mac address option for new radios")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unnecessary break statement in the default case of bw switch
block in mt76x2_mac_process_tx_rate routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have check if queue is not empty when start flushing queues on
by mac80211 callback, but we also can start flushing queues by internal
driver calls. So move check into rt2x00queue_flush_queue() to assure
we do not flush empty queue anytime.
Additionally add warning if we start to kick empty queue as in such
situation we set wrong index in the HW queue, what can confuse the HW
and have various negative consequences.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
we do not need generic version of those.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Revision 7 of PCIe dongle interface increases the item size of tx and rx
complete rings to accommodate extra payload for new feature. This patch
simply bump up the size of these two rings without adding the support
for utilizing the new space. This makes brcmfmac compatible with rev7
firmware.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum nl80211_band used to retrieve wiphy->bands is the same as
wiphy->bands->band which is checked by wiphy_register(). So it can be used
directly as parameter of ieee80211_channel_to_frequency().
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential execution path in which variable ret is returned
without being properly initialized previously.
Fix this by storing the value returned by function
rsi_usb_master_reg_write into _ret_.
Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable")
Fixes: 16d3bb7b2f ("rsi: disable fw watchdog timer during reset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.
Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.
Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c4762f ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.
In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.
Remove this manual power on/off sequence as it is in-fact not needed.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
dma_tx_fragment() is never called in atomic context.
dma_tx_fragment() is only called by b43legacy_dma_tx(), which is
only called by b43legacy_tx_work().
b43legacy_tx_work() is only set a parameter of INIT_WORK() in
b43legacy_wireless_init().
Despite never getting called from atomic context,
dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During changing virtual interface, keep using previous net device
mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface type changed, firmware using a new connction pointer.
We need Re-configure the mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For user configurated mac address, directly set to firmware with no change.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The check within mt76_txq_send_burst is not enough, as it happens after
a first frame has already been queued up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids having the tid or station entry disappear prematurely.
Also cancel the reorder work earlier to avoid further processing delayed
by waiting for the lock to be released
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a spinlock in mt76_rx_complete. Without this, multiple stats updates
could happen in parallel, which can lead to deadlocks. There are
probably more corner cases fixed by this change.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix is_mt7612 routine since asic version is set in mt76_dev revision
field and not in mt76x2_dev one.
Moreover remove mt76x2_dev rev field since it is never used in the
driver
Fixes: 7bc04215a6 ('mt76: add driver code for MT76x2e')
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
wireless-drivers fixes for 4.17
A few fixes for 4.17 but nothing really special. The new ETSI WMM
parameter support for iwlwifi is not technically a bugfix but
important for regulatory compliance.
iwlwifi
* use new ETSI WMM parameters from regulatory database
* fix a regression with the older firmware API 31 (eg. 31.560484.0)
brcmfmac
* fix a double free in nvmam loading fails
rtlwifi
* yet another fix for ant_sel module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
