For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue. This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected. More detailed analysis indicated that the
default 25us delay was higher than necessary. Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc). This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary. This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.
Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements. This will eliminate the need
to reconfigure a hardware queue internal buffers at run time. After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.
This patch only adds the basic mapping logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional logic to reserve completion rings for the bnxt_re driver
when it requests MSIX vectors. The function bnxt_cp_rings_in_use()
will return the total number of completion rings used by both drivers
that need to be reserved. If the network interface in up, we will
close and open the NIC to reserve the new set of completion rings and
re-initialize the vectors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver code makes some assumptions about the group index
and the map index of rings. This makes the code more difficult to
understand and less flexible.
Improve it by adding the grp_idx and map_idx fields explicitly to the
bnxt_ring_struct as a union. The grp_idx is initialized for each tx ring
and rx agg ring during init. time. We do the same for the map_idx for
each cmpl ring.
The grp_idx ties the tx ring to the ring group. The map_idx is the
doorbell index of the ring. With this new infrastructure, we can change
the ring index mapping scheme easily in the future.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for the maximum pre-set TX channels for ethtool -l, we
need to check the current max_tx_scheduler_inputs parameter from firmware.
This parameter specifies the max input for the internal QoS nodes currently
available to this function. The function's TX rings will be capped by this
parameter. By adding this logic, we provide a more accurate pre-set max
TX channels to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RDMA driver is registered, use a new VNIC mode that allows
RDMA traffic to be seen on the netdev in promiscuous mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes wmb() followed by writel(). writel() already has a barrier on
some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a wmb().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Also add mmiowb() so that write code doesn't move outside of scope.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag(). The current code is only
passing the 12-bit tag and it is missing the priority bits.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver exports different switchdev PARENT_IDs for
representors belonging to different SR-IOV PF-pools of an adapter.
This is not correct as the adapter can switch across all vports
of an adapter. This patch fixes this by exporting a common switchdev
PARENT_ID for all reps of an adapter. The PCIE DSN is used as the id.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context. This will allow "ip link show"
to display all VF MAC addresses.
Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.
Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.
The min is the absolute minimum for each VF to function. The max is the
global resources minus the resources used by the PF. Each VF is
guaranteed the min. Up to max resources may be available for some VFs.
The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources. The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources. Use the new API when it is supported by firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized. Otherwise they cannot be re-used by
the PF. For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.
To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version has new firmware APIs to allocate PF/VF resources more
flexibly.
New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the changes needed for the bnxt_en driver to add support
for dynamic interrupt moderation per ring.
This does add additional counters in the receive path, but testing shows
that any additional instructions are offset by throughput gain when the
default configuration is for low latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver hook points for xdp_rxq_info:
* reg : bnxt_alloc_rx_rings
* unreg: bnxt_free_rx_rings
This driver should be updated to re-register when changing
allocation mode of RX rings.
Tested on actual hardware.
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
TC flower is not enabled on VFs and when there's no FW support.
Alloc the tc_info{} struct at init time only when TC flower is being
enabled.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements periodic querying of cfa flow stats
in batches to compute the 'lastused' attribute of TC flow stats.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv4 vxlan encap/decap action support to TC-flower
offload.
For vxlan encap, the driver maintains a tunnel encap hash-table.
When a new flow with a tunnel encap action arrives, this table
is looked up; if an encap entry exists, it uses the already
programmed encap_record_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new encap node is added and the
L2 header fields are queried via a route lookup.
hwrm_cfa_encap_record_alloc cmd is used to create a new encap
record and the encap_record_handle is used as the tunnel_handle
while adding the flow.
For vxlan decap, the driver maintains a tunnel decap hash-table.
When a new flow with a tunnel decap action arrives, this table
is looked up; if a decap entry exists, it uses the already
programmed decap_filter_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new decap node is added and
a decap_filter_handle is alloc'd via the hwrm_cfa_decap_filter_alloc
cmd. This handle is used as the tunnel_handle while adding the flow.
The code to issue the HWRM FW cmds is introduced in a follow-up patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IRQ coalescing logic is a little messy. The ethtool
parameters are mapped to hardware parameters in a way that is difficult
to understand. The first step is to better organize the parameters
by adding the new structure bnxt_coal. The structure is used by both
the RX and TX sets of coalescing parameters.
Adjust the default coal_ticks to 14 us and 28 us for RX and TX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NICs have a firmware enforced maximum MTU setting by management
firmware. Set up netdev->max_mtu accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex. This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer. The rare problem shows up when running ethtool -i repeatedly.
Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.
Fixes: 90c694bb71 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading TC based flow
rules and actions for the 'flower' classifier in the bnxt_en driver.
It includes logic to parse flow rules and actions received from the
TC subsystem, store them and issue the corresponding
hwrm_cfa_flow_alloc/free FW cmds. L2/IPv4/IPv6 flows and drop,
redir, vlan push/pop actions are supported in this patch.
In this patch the hwrm_cfa_flow_xxx routines are just stubs.
The code for these routines is introduced in the next patch for easier
review. Also, the code to query the TC/flower action stats will
be introduced in a subsequent patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce default rings from 8 to 4 on multi-port cards to reduce memory
usage.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCIe device ID for bcm58802 and bcm58808. Also add chip number
update to declare bcm588xx as chip class phase 4 and later
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides hints to irqbalance to map bnxt_en device IRQs
to specific CPU cores. cpumask_local_spread() is used, which first
maps IRQs to near NUMA cores; when those cores are exhausted, IRQs
are mapped to far NUMA cores.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of TX rings is changed (e.g. ethtool -L, enabling XDP TX
rings, etc), the current code tries to reserve the new number of TX rings
before closing and re-opening the NIC. If we are unable to reserve the
new TX rings, we abort the operation and keep the current TX rings.
The problem is that the firmware will disable the current TX rings even
when it cannot reserve the new set of TX rings. We fix it as follows:
1. Instead of reserving the new set of TX rings, just ask the firmware
to check if the new set of TX rings is available. There is a flag in
the firmware message to do that. If not available, abort and the
current TX rings will not be disabled.
2. Do the actual TX ring reservation in the path that opens the NIC.
We keep the number of TX rings currently successfully reserved. If the
number of TX rings is different than the reserved TX rings, we call
firmware and reserve again.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the switchdev_port_attr_get() and
ndo_get_phys_port_name() methods for the PF and the VF-reps.
Using this support a user application can deduce that the PF
(when in the ESWITCH_SWDEV mode) and it's VF-reps form a switch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the RX/TX and a simple netdev implementation
for VF-reps. The VF-reps use the RX/TX rings of the PF. For each VF-rep
the PF driver issues a VFR_ALLOC FW cmd that returns "cfa_code"
and "cfa_action" values. The FW sets up the filter tables in such
a way that VF traffic by default (in absence of other rules)
gets punted to the parent PF. The cfa_code value in the RX-compl
informs the driver of the source VF. For traffic being transmitted
from the VF-rep, the TX BD is tagged with a cfa_action value that
informs the HW to punt it to the corresponding VF.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a part of a patch-set that introduces support for
VF-reps in the bnxt_en driver. The driver registers eswitch mode
get/set methods with the devlink interface that allow a user to
enable SRIOV switchdev mode. When enabled, the driver registers
a VF-rep netdev object for each VF with the stack. This can
essentially bring the VFs unders the management perview of the
hypervisor and applications such as OVS.
The next patch in the series, adds the RX/TX routines and a slim
netdev implementation for the VF-reps.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report DCB_CAP_DCBX_LLD_MANAGED only if the firmware DCBX agent is enabled
and running for PF or VF. Otherwise, if both LLDP and DCBX agents are
disabled in firmware, we report DCB_CAP_DCBX_LLD_HOST and allow host
IEEE DCB settings. This patch refines the current logic in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve and store the hardware bridge mode, so that we can implement
ndo_bridge_{get|set)link methods in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF representors and PTP are added features in the new firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing channels from combined to rx/tx or vice versa, the code
uses the wrong "sh" parameter to determine if we are reserving rings
for shared or non-shared mode. It should be using the ethtool requested
"sh" parameter instead of the current "sh" parameter.
Fix it by passing the "sh" parameter to bnxt_reserve_rings(). For
ethtool, we will pass in the requested "sh" parameter.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ndo_get_stats64() may not be protected by RTNL and can race with
.ndo_stop() or other ethtool operations that can free the statistics
memory. Fix it by setting a new flag BNXT_STATE_READ_STATS and then
proceeding to read statistics memory only if the state is OPEN. The
close path that frees the memory clears the OPEN state and then waits
for the BNXT_STATE_READ_STATS to clear before proceeding to free the
statistics memory.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get a TPA_END completion to handle a completed LRO packet, it
is possible that hardware would indicate errors. The current code is
not checking for the error condition. Define the proper error bits and
the macro to check for this error and abort properly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips require the doorbells to be written twice, but newer chips
do not. Add a new common function bnxt_db_write() to write all
doorbells appropriately depending on the chip. Eliminating the extra
doorbell on newer chips has a significant performance improvement
on pktgen.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional chip definitions and macros for all supported chips.
Add a new macro BNXT_CHIP_P4_PLUS for the newer generation of chips and
use the macro to properly determine the features supported by these
newer chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new short message format is used on the new BCM57454 VFs. Each
firmware message is a fixed 16-byte message sent using the standard
firmware communication channel. The short message has a DMA address
pointing to the legacy long firmware message.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change restricts the PF in multi-host mode from setting any port
level PHY configuration. The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
