For picasso(adev->pdev->device == 0x15d8)&raven2(adev->rev_id >= 0x8),
firmware is sufficient to support gfxoff.
In commit 98f58ada2d, for picasso&raven2,
return directly and cause gfxoff disabled.
Fixes: 98f58ada2d ("drm/amdgpu/gfx9: update pg_flags after determining if gfx off is possible")
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needs ATPX rather than _PR3 to really turn off the dGPU. This can save
~5W when dGPU is runtime-suspended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement HW I2C enigne controller to be used by the RAS EEPROM
table manager. This is based on code from ATITOOLs.
v2:
Rename the file and all function prefixes to smu_v11_0_i2c
By Luben's observation always fill the TX fifo to full so
we don't have garbadge interpreted by the slave as valid data.
v3:
Remove preemption disable as the HW I2C controller will not
stop the clock on empty TX fifo and so it's not critical to
keep not empty queue.
Switch to fast mode 400 khz SCL clock for faster read and write.
v5:
Restore clock gating before releasing I2C bus and fix some
style comments.
v6:
squash in warning fix, fix includes (Alex)
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add RAS EEPROM table manager to eanble RAS errors to be stored
upon appearance and retrived on driver load.
v2: Fix some prints.
v3:
Fix checksum calculation.
Make table record and header structs packed to do correct byte value sum.
Fix record crossing EEPROM page boundry.
v4:
Fix byte sum val calculation for record - look at sizeof(record).
Fix some style comments.
v5: Add description to EEPROM_TABLE_RECORD_SIZE and syntax fixes.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where status
registers requiring HW to update have a 1 cycle delay, due to the
register update having to go through GRBM.
SW may operate on an incorrect value if they write a register and
immediately check the corresponding status register.
Registers requiring HW to clear or set fields may be delayed by 1 cycle.
For example,
1. write VM_INVALIDATE_ENG0_REQ mask = 5a
2. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. HW will reset VM_INVALIDATE_ENG0_ACK = 0 until invalidation is complete
3. write VM_INVALIDATE_ENG0_REQ mask = 5a
4. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. First read of VM_INVALIDATE_ENG0_ACK = 5a instead of 0
b. Second read of VM_INVALIDATE_ENG0_ACK = 0 because
the remote GRBM h/w register takes one extra cycle to be cleared
c. In this case, SW will see a false ACK if they exit on first read
Affected registers (only GC variant) | Recommended Dummy Read
--------------------------------------+----------------------------
VM_INVALIDATE_ENG*_ACK | VM_INVALIDATE_ENG*_REQ
VM_L2_STATUS | VM_L2_STATUS
VM_L2_PROTECTION_FAULT_STATUS | VM_L2_PROTECTION_FAULT_STATUS
VM_L2_PROTECTION_FAULT_ADDR_HI/LO32 | VM_L2_PROTECTION_FAULT_ADDR_HI/LO32
VM_L2_IH_LOG_BUSY | VM_L2_IH_LOG_BUSY
MC_VM_L2_PERFCOUNTER_HI/LO | MC_VM_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER_HI/LO | ATC_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER2_HI/LO | ATC_L2_PERFCOUNTER2_HI/LO
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long type for the same ras count variable.
This will avoid overflow on 64 bit system.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Implement PowerUpSDMA/PowerDownSDMA interfaces in the swSMU for renoir
2.adjust smu ip block ahead of gfx&sdma ip block
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: set num_types based on num_instances
navi1x has 2 sdma engines but commit
"e7b58d03b678 drm/amdgpu: reorganize sdma v4 code to support more instances"
changes the max number of sdma irq types (AMDGPU_SDMA_IRQ_LAST) from 2 to 8
which causes amdgpu_irq_gpu_reset_resume_helper() to recover irq of sdma
engines with following logic:
(enable irq for sdma0) * 1 time
(enable irq for sdma1) * 1 time
(disable irq for sdma1) * 6 times
as a result, after gpu reset, interrupt for sdma1 is lost.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/nv.c: In function 'nv_common_early_init':
drivers/gpu/drm/amd/amdgpu/nv.c:471:7: warning:
variable 'psp_enabled' set but not used [-Wunused-but-set-variable]
It's not used since inroduction in
commit c6b6a42175 ("drm/amdgpu: add navi10 common ip block (v3)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Error out if the AMDGPU_CS ioctl is called with multiple SYNCOBJ_OUT and/or
TIMELINE_SIGNAL chunks, since otherwise the last chunk wins while the
allocated array as well as the reference counts of sync objects are leaked.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
firmware header information is printed for direct fw loading but not
added for psp fw loading yet
v2: squash in warning fix (Alex)
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to set certain power gating flags after we determine
if the firmware version is sufficient to support gfxoff.
Previously we set the pg flags in early init, but we later
we might have disabled gfxoff if the firmware versions didn't
support it. Move adding the additional pg flags after we
determine whether or not to support gfxoff.
Fixes: 005440066f ("drm/amdgpu: enable gfxoff again on raven series (v2)")
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
When VM state changed and system in large bar mode,
make sure to use CPU update function, otherwise use
SDMA function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gang Ba <gaba@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have done this for pre-GFX10 asics, but GFX10 did not pick up the
new change. The below is the commit message for that change.
This is recommended by HW designers. Previously when it was set to 1,
the PDE walk error in VM fault will be treated as
PERMISSION_OR_INVALID_PAGE_FAULT rather than usually expected OTHER_FAULT.
As a result, the retry control in VM_CONTEXT*_CNTL will change accordingly.
The above behavior is kind of abnormal. Furthermore, the
PDE_FAULT_CLASSIFICATION == 1 feature was targeted for very old ASICs
and it never made it way to production. Therefore, we should set it to 0.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
