Currently the debounce time pinconfig option uses an unspecified
"time units" unit. As pinconfig options should use SI units and a
real unit is also necessary for generic dt bindings, change it
to usec. Currently no driver is using the generic pinconfig option
for this, so the unit change is safe to do.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PULL_PIN_DEFAULT is meant for hardware completely hiding any pull
settings from the driver, so that it's really only possible to turn
the pull on or off, but it not being possible to determine any
pull settings from software.
Also the binding-documentation for the pull arguments did not match
the changes to the expected values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is counter-intuitive to have "0" mean disable in a boolean
manner for electronic properties of pins such as pull-up and
pull-down. Therefore, define that a pull-up/pull-down argument
of 0 to such a generic option means that the pin is
short-circuited to VDD or GROUND. Pull disablement shall be
done using PIN_CONFIG_BIAS_DISABLE.
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by Heiko Stuebner <heiko@sntech.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There exist controllers that don't support to set the pull to up or down
separately but instead automatically set the pull direction based on
embedded knowledge inside the controller, for example depending on the
selected mux function of the pin.
Therefore this patch adds another config option to use this default
pull-state for a pin where it is not possible to know or decide if the
pin will be pulled up or down.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new PIN_CONFIG_BIAS_BUS_HOLD pin configuration for a bus holder
pin mode (also known as bus keeper, or repeater). This is a weak latch
which drives the last value on a tristate bus. Another device on the bus
can drive the bus high or low before going tristate to change the value
driven by the pin.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to
PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pin configurations IP allows to set the current output to the pin.
This patch adds such a parameter to the pinconf-generic mechanism.
This parameter takes as argument the drive strength in mA.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a definition of a generic output configuration
for a certain pin when using the generic pin configuration
library. Whereas driving pins low/high is usually a GPIO
business, you may want to set up pins into a default state
using hogs, and never touch them again. This helps out
with that scenario.
Based on a patch from Patrice Chotard.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a split-off from the earlier patch set which adds generic
pin configuration for the pin controllers that want it. Since
we may have a system with mixed generic and custom pin controllers,
we pass a boolean in the pin controller ops vtable to indicate
if it is generic.
ChangeLog v1->v5:
- Follow parent patch versioning number system.
- Document the semantic meaning of return values from pin config
get functions, so we can iterate over pins and check their
properties from debugfs as part of the generic config code.
- Use proper cast functions in the generic debugfs pin config
file.
- Expand generic config to optionally cover groups too.
ChangeLog v5->v6:
- Update to match underlying changes.
ChangeLog v6->v7:
- Drop DRIVE_OFF parameter, use bias high impedance for this
- Delete argument for drive modes push-pull, od and os. These
are now just state transitions.
- Delete slew rate rising/falling due to discussions on on
proper semantics
- Drop config wakeup, struct irq_chip does this for now, add
back if need be.
- Set PIN_CONFIG_END to 0x7fff making room for custom config
parameters from 0x8000 and up.
- Prefix accessor functions with pinconf_
