phy-supply is a phandle to the regulator that provides power to the
PHY. This regulator is managed during the PHY power on/off sequence
by the phy core driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
This panel is used by the Medcom Wide and supported by the
simple-panel driver.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.
As this is not always the case, the regulator is requested as optional.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Allwinner A23 SoC has a PRCM unit like the previous A31 SoC.
The differences are the AR100 clock can no longer be modified,
the APB0 clock has different divisors, and some clock gates are
gone.
This patch adds a compatible with a modified subdevice list for
the A23.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Merge "ARM: mvebu: DT changes for v3.17 (round 2)" from Jason Cooper:
mvebu DT changes for v3.17 (round 2):
- kirkwood
* Add d2 Network v2 board
- mvebu
* Add Armada 375 ethernet node
* Add CA9 MPcore SoC controller node
* Add support for dynamic freq scaling on Armada XP
* tag 'mvebu-dt-3.17-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update Armada XP DT for dynamic frequency scaling
ARM: mvebu: add CA9 MPcore SoC Controller node
ARM: mvebu: Enable the network controller in Armada 375 DB board
ARM: mvebu: Add support for the network controller in Armada 375 SoC
ARM: Kirkwood: add DT support for d2 Network v2
ARM: Kirkwood: allow to use netxbig DTSI for d2net_v2 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung exynos cpuidle update for v3.17" from Kukjin Kim:
- add callbacks exynos_suspend() and exynos_powered_up()
for support cpuidle through mcpm
- skip exynos_cpuidle for exynos5420 because is uses
cpuidle-big-liggle generic cpuidle driver
- add generic functions to calculate cpu number is used
for pmu and this is required for exynos5420 multi-cluster
- add of_device_id structure for big.LITTLE cpuidle and
add "samsung,exynos5420" compatible string for exynos5420
* tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung cleanup for v3.17" from Kukjin Kim:
Most of them are for exynos SoCs, remove useless codes and update for
PMU consolidation.
- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos
- move SYSREG definitions into mach-exynos/regs-sys.h
- add mapping PMU base address via DT for PMU cleanup
- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add support for mapping PMU base address via DT
ARM: EXYNOS: Remove "linux/bug.h" from pmu.c
ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain
ARM: EXYNOS: Remove file path from comment section
ARM: EXYNOS: Move SYSREG definition into sys-reg specific file
ARM: EXYNOS: Make exynos machine_ops as static
ARM: EXYNOS: Remove unused code in common.h
ARM: debug: Update Samsung UART config options
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: device tree changes for 3.17" from Thierry Reding:
- New board support:
* Apalis T30
- HDA support for Tegra124 and Venice2
- Display on Medcom Wide and Roth
- GK20A support on Tegra124
- XUSB pad controller for Tegra124 and Jetson TK1
- Various cleanups
This pulls in the for-3.17/fuse-move, for-3.17/dt-cros-ec-kbd and
for-3.17/xusb-padctl branches to resolve dependencies.
Note that the Apalis T30 support has a runtime dependency on the
for-3.17/pcie-regulators branch, so they should preferably be applied
in that order. I didn't merge that branch into this because Apalis T30
support is new, therefore can't regress, and because the dependency
exists only at runtime.
* tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
ARM: tegra: roth: add display DT node
ARM: tegra: Fix typoed ams,ext-control properties
ARM: tegra: jetson-tk1: Add XUSB pad controller
ARM: tegra: tegra124: Add XUSB pad controller
ARM: tegra: add GK20A GPU to Tegra124 DT
ARM: tegra: of: add GK20A device tree binding
ARM: tegra: roth: enable input on mmc clock pins
ARM: tegra: roth: fix unsupported pinmux properties
ARM: tegra: Migrate Apalis T30 PCIe power supply scheme
ARM: tegra: tamonten: add the display to the Medcom Wide
ARM: tegra: tamonten: add the base board regulators
ARM: tegra: initial support for apalis t30
ARM: tegra: jetson-tk1: mark eMMC as non-removable
ARM: tegra: venice2 - Enable HDA
ARM: tegra: Add Tegra124 HDA support
ARM: tegra: Add the EC i2c tunnel to tegra124-venice2
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
pinctrl: Add NVIDIA Tegra XUSB pad controller support
of: Add NVIDIA Tegra XUSB pad controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: rework PCIe regulators" from Thierry Reding:
This branch reworks the set of regulators that the Tegra PCIe driver
uses, so that the driver and DT bindings more correctly model what's
really going on in HW. For backwards-compatibility the driver will
fallback to using the old set of regulators if the new ones can't be
found.
I've made this a separate branch in case it needs to be pulled into the
PCIe tree to resolve any conflicts.
* tag 'tegra-for-3.17-pcie-regulators' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: tegra: Add new PCIe regulator properties
PCI: tegra: Overhaul regulator usage
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: move fuse code out of arch/arm" from Thierry Reding:
This branch moves code related to the Tegra fuses out of arch/arm and
into a centralized location which could be shared with ARM64. It also
adds support for reading the fuse data through sysfs.
Included is also some preparatory work that moves Tegra-related header
files from include/linux to include/soc/tegra as suggested by Arnd.
Furthermore the Tegra chip ID is now retrieved using a function rather
than a variable so that sanity checks can be done. This is convenient
in subsequent patches that will move some of the code that's currently
called from Tegra machine setup into regular initcalls so that it can
be reused on 64-bit ARM. The sanity checks help with verifying that no
code tries to obtain the Tegra chip ID before the underlying driver is
properly initialized.
* tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: device tree updates for 3.17" from Shawn Guo:
The i.MX device tree updates for 3.17:
- Add device tree sources and pin function header for i.MX6SX SoC
- Initial imx6sx-sdb board support with FEC, MMC, USB, PMIC, Audio
and GPIO key enabled
- New board support: mbimxsd25 and mbimxsd27 from Eukrea, aristainetos
imx6dl boards, Rex Pro and Basic, Ka-Ro TX6
- Restructure imx6qdl-wandboard.dtsi for new rev C1 board
- Split M28EVK and M53EVK into SoM and EVK parts
- A few correction around SDMA, SSI and SATA device nodes
- Add eSATA support for Cubox-i board
- Updates on edmqmx6 to enable PCIe, I2C and CAN
- Use DT macro for clock ID for imx27 and imx6qdl
- Add FlexCAN support for VF610 SoC
* tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (125 commits)
ARM: dts: vf610: add FlexCAN node
ARM: dts: add initial Rex Basic board support
ARM: dts: add initial Rex Pro board support
ARM: dts: mx5: Split M53EVK into SoM and EVK parts
ARM: dts: imx6: RIoTboard explicitly define pad settings
ARM: dts: vf610: fix length of eshdc1 register property
ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
ARM: dts: imx53: correct clock-names of SATA node
ARM: imx6: Align ssi nodes between mx6 variants
ARM: i.MX27 clk: dts: Use clock defines in DTS files
ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
ARM: dts: imx6sx-sdb: Add audio support
ARM: dts: imx6sx: Pass the fsl,fifo-depth property
ARM: dts: imx6sx: Fix sdma node
ARM: dts: imx6: edmqmx6: Add can bus
ARM: dts: imx6: edmqmx6: Add two other i2c buses
ARM: dts: imx6: edmqmx6: Add PCIe support
ARM: dts: imx25-pdk: Add USB OTG support
ARM: dts: i.MX53: add aipstz nodes
ARM: dts: mxs: Split M28EVK into SoM and EVK parts
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: SoC changes for 3.17" from Shawn Guo:
The i.MX SoC changes for 3.17:
- Add devicetree support for i.MX1 and i.MX21 clock driver
- Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
- Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
device tree boot
- Remove i.MX1 camera support
- Remove i.MX27 IP Camera and Lite-Kit board support
- Add suspend and cpuidle support for i.mx6sx
- Clean up unused clk_register_clkdev() lookups
- Update imx-weim bus driver to support populating devices on a simple
bus
- Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
- Make i.MX51 a DT only platform and clean up the non-DT support code
- Support disabling supervisor protect via DT
- Random defconfig updates
* tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (69 commits)
ARM: imx: clk-vf610: fix FlexCAN clock gating
ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
ARM: i.MX53: globally disable supervisor protect
ARM: i.MX: allow disabling supervisor protect via DT
ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
ARM: i.MX27 clk: Remove unused definitions
ARM: i.MX27 clk: Introduce DT include for clock provider
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
ARM: i.MX: Remove i.MX1 camera support
ARM: imx: use PTR_ERR_OR_ZERO
bus: imx-weim: populate devices on a simple bus
ARM: imx: build cpu_is_imx6sl function conditionally
ARM: imx: imx6sx uses imx6q cpuidle code
ARM: imx: drop PL310 errata 588369 and 727915
ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
ARM: imx: mark .dt_compat as const
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device tree binding documentation for the SATA
controller found on NVIDIA Tegra SoCs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a driver for clock controller being a part of Audio
Subsystem present on S5PV210 and compatible SoCs. It is used to provide
clocks for other IP blocks of this subsystem.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new, Common Clock Framework-based clock driver for Samsung
S5PV210 and compatible SoCs. The driver is just added, without enabling it yet.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[t.figa: Added support for other SoC variants and clock output. Fixed
remaining minor issues.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.
For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.
The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.
Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These power supply properties are no longer needed since the binding now
contains the full set properties to accurately describe the power supply
inputs of the Tegra PCIe block.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds devicetree support CCM module for i.MX21 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Instead of using enum for clock ID, let's switch imx6qdl clock driver to
use macro. In this case, device tree can reuse these macros to improve
readability.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds devicetree support CCM module for i.MX1 (MC9328MX1) CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
UART modules on some SoCs only differ in the fifosize of each
UART channel. Its useless to duplicate the drv_data structure
or create a compatible name for such a change.
We can get fifosize via the device tree nodes (not mandating it).
Also updates the documentation.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung SPI driver now uses the generic SPI "cs-gpios"
binding so update the documentation accordingly.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[javier.martinez@collabora.co.uk: split changes and improve commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support the TI TAS2552 Class D amplifier.
The TAS2552 is a high efficiency Class-D audio
power amplifier with advanced battery current
management and an integrated Class-G boost
The device constantly measures the
current and voltage across the load and provides a
digital stream of this information.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the device tree binding documentation for the GK20A GPU used in
Tegra K1 SoCs.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds the device tree to support Toradex Apalis T30, a
computer on module which can be used on different carrier boards.
The module consists of a Tegra 3 SoC, two PMICs, 1 or 2 GB of DDR3L
RAM, eMMC, an LM95245 temperature sensor chip, an i210 resp. i211
gigabit Ethernet controller, an STMPE811 ADC/touch controller as well
as two MCP2515 CAN controllers. Furthermore, there is an SGTL5000 audio
codec which is not yet supported. Anything that is not self contained
on the module is disabled by default.
The device tree for the Evaluation Board includes the modules device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
While at it also add the device tree binding documentation for Apalis
T30.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[swarren: fixed some node sort orders]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Docbook creation was broken. We need to move after
v3.16-rc1-3-ga981296f048b in order to get commit
a981296f04.
Linux 3.16-rc5
* tag 'v3.16-rc5': (985 commits)
Linux 3.16-rc5
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
parisc: drop unused defines and header includes
parisc: fix fanotify_mark() syscall on 32bit compat kernel
parisc: add serial ports of C8000/1GHz machine to hardware database
ext4: fix potential null pointer dereference in ext4_free_inode
ext4: fix a potential deadlock in __ext4_es_shrink()
Documenation/laptops: rename and update hpfall.c
DocBook: fix various typos
DocBook: fix mtdnand typos
scripts/kernel-doc: handle object-like macros
Documentation/Changes: clean up mcelog paragraph
ARM: at91: at91sam9x5: add clocks for usb device
phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
phy: core: Fix error path in phy_create()
drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
phy: omap-usb2: fix devm_ioremap_resource error detection code
phy: sun4i: depend on RESET_CONTROLLER
USB: serial: ftdi_sio: Add Infineon Triboard
...
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
