IO domain voltages on some Rockchip SoCs are variable but need to be
kept in sync between the regulators and the SoC using a special
register.
A specific example using rk3288:
- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to
that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
Said another way, this driver simply handles keeping bits in the SoC's
general register file (GRF) in sync with the actual value of a voltage
hooked up to the pins.
Note that this driver specifically doesn't include:
- any logic for deciding what voltage we should set regulators to
- any logic for deciding whether regulators (or internal SoC blocks)
should have power or not have power
If there were some other software that had the smarts of making
decisions about regulators, it would work in conjunction with this
driver. When that other software adjusted a regulator's voltage then
this driver would handle telling the SoC about it. A good example is
vqmmc for SD. In that case the dw_mmc driver simply is told about a
regulator. It changes the regulator between 3.3V and 1.8V at the
right time. This driver notices the change and makes sure that the
SoC is on the same page.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman: fix compiler warnings]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Pull "Allwinner drivers additions for 3.18" from Maxime Ripard:
Nothing major, just handling the RTC driver changes needed for the A31/A23.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'sunxi-drivers-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
Pull "Fifth Round of Renesas ARM Based SoC DT Updates for v3.18" from Simon Horman:
* Document manufacturer for KZM boards
* Use SoC-specific irqc compatible property
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-dt5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Add manufacturer for KZM boards
ARM: shmobile: r8a73a4 dtsi: Add SoC-specific irqc compatible property
Pull "ARM: tegra: core SoC code changes for 3.18" from Stephen Warren:
the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.
An unused header file was also removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: remove unused tegra_emc.h
ARM: tegra: Initialize flow controller from DT
of: Add NVIDIA Tegra flow controller bindings
Pull devicetree bug fixes and documentation from Grant Likely:
"Several bug fix commits for issues found in the v3.17 rc series.
Most of these are minor in that they aren't actively dangerous, but
they have been seen in the wild. The one important fix is commit
7dbe5849fb ("of: make sure of_alias is initialized before accessing
it"), without which some powerpc platforms will fail to find stdout
for the console"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/fdt: fix memory range check
of: Fix memory block alignment in early_init_dt_add_memory_arch()
of: make sure of_alias is initialized before accessing it
of: Documentation regarding attaching OF Selftest testdata
of: Disabling OF functions that use sysfs if CONFIG_SYSFS disabled
of: correct of_console_check()'s return value
Kishon writes:
Adds 3 new PHY drivers stih407, stih41x and rcar gen2 PHY. It also
includes miscellaneous cleanup of other PHY drivers.
Conflicts:
MAINTAINERS
These are the specific changes for ARM64 to make it possible to integrate the
DT based generic cpuidle driver in this tree.
It contains:
* The documentation for the DT definitions for ARM
* The refactoring of the cpu_suspend function for ARM64
* Introduce the cpu_idle_init function for ARM64
* Add the PSCI CPU SUSPEND based on the previous changes on cpu_suspend
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge "ARM: imx: device tree changes for 3.18" from Shawn Guo:
The i.MX device tree changes for 3.18:
- Device tree support for i.MX ADS and Armadeus APF9328 boards
- Enable thermal sensor support for i.MX6SL
- Add LCD support for i.MX6SL EVK board
- Fix display duplicate name for a bunch of board dts files
- Configure imx6qdl-sabresd board pins locally to remove the dependency
on bootloader
- A set of imx28-tx28 board dts updates from Lothar
- Add pci config space as platform resource
- Enable devices RTC, I2C and HDMI for nitrogen6x board
- Split HummingBoard DT to support s/dl and d/q
- mSATA and IR input support for HummingBoard
- Add SSI baud clock for i.MX6 device trees
- Add USB support for vf610-colibri and vf610-twr boards
- A set of cleanup and updates on Gateworks boards
* tag 'imx-dt-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (86 commits)
ARM: dts: imx6: make gpt per clock can be from OSC
ARM: dts: imx: ventana: add canbus support for GW52xx
ARM: dts: imx: ventana: cleanup pinctrl groups
ARM: dts: imx: ventana: configure padconf for all pins
ARM: dts: imx: ventana: use gpio constants
ARM: dts: imx: ventana: remove unused aliases
ARM: dts: imx: ventana: remove unsupported dt nodes
ARM: dts: imx28-tx28: add alias for CAN XCVR regulator
ARM: dts: imx28-tx28: add spi-gpio as alternative for spi-mxs
ARM: dts: imx28-tx28: use GPIO flags
ARM: dts: imx28-tx28: remove spidev labels and add third instance of spidev
ARM: dts: imx6sl: add baud clock and clock-names for ssi
ARM: dts: imx6qdl: add baud clock and clock-names for ssi
ARM: dts: imx6qdl-sabresd: Configure the pins locally
ARM: dts: imx28-m28evk: Fix display duplicate name warning
ARM: dts: imx28-tx28: Fix display duplicate name warning
ARM: dts: imx28-m28cu: Fix display duplicate name warning
ARM: dts: imx28-cfa100: Fix display duplicate name warning
ARM: dts: imx28-apf28dev: Fix display duplicate name warning
ARM: dts: imx28-apx4devkit: Fix display duplicate name warning
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the missing 'compatible' property to device tree root node of
- mt6589-aquaris5.dts
and document the new values.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "soc: Keystone SOC Navigator drivers for 3.18" from Santosh Shilimkar:
Keystone SOC Navigator drivers for 3.18
The Keystone Multi-core Navigator contains QMSS and packet DMA
subsystems which interwork together to form the Navigator cloud
used by various subsystems like NetCP, SRIO, SideBand Crypto
engines etc.
* tag 'drivers-soc-ti-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Add document describing device tree bindings for MAX14577 MFD
drivers: MFD core, extcon, regulator and charger.
Both MAX14577 and MAX77836 chipsets are documented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Keystone Navigator DMA driver sets up the dma channels and flows for
the QMSS(Queue Manager SubSystem) who triggers the actual data movements
across clients using destination queues. Every client modules like
NETCP(Network Coprocessor), SRIO(Serial Rapid IO) and CRYPTO
Engines has its own instance of packet dma hardware. QMSS has also
an internal packet DMA module which is used as an infrastructure
DMA with zero copy.
Initially this driver was proposed as DMA engine driver but since the
hardware is not typical DMA engine and hence doesn't comply with typical
DMA engine driver needs, that approach was naked. Link to that
discussion -
https://lkml.org/lkml/2014/3/18/340
As aligned, now we pair the Navigator DMA with its companion Navigator
QMSS subsystem driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of
the main hardware sub system which forms the backbone of the Keystone
Multi-core Navigator. QMSS consist of queue managers, packed-data structure
processors(PDSP), linking RAM, descriptor pools and infrastructure
Packet DMA.
The Queue Manager is a hardware module that is responsible for accelerating
management of the packet queues. Packets are queued/de-queued by writing or
reading descriptor address to a particular memory mapped location. The PDSPs
perform QMSS related functions like accumulation, QoS, or event management.
Linking RAM registers are used to link the descriptors which are stored in
descriptor RAM. Descriptor RAM is configurable as internal or external memory.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently the DP_PHY_ENABLE register is mapped in the driver,
and accessed to control power to the PHY.
With mfd-syscon and regmap interface available at our disposal,
it's wise to use that instead of using a 'reg' property for the
controller and allocating a memory resource for that.
To facilitate this, we have added another compatible string
for Exynso5420 SoC to acquire driver data which contains
different DP-PHY-CONTROL register offset.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds dt documentation bindings for the usb phy found
on STiH415/5 SoC's from STMicroelectronics, which support USB 1.1 and 2.0.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds the dt documentation for the usb picophy found on stih407 SoC family
available from STMicroelectronics.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.
This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing of USB channels to the controller be dynamic, depending on what
USB drivers are loaded, rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c seems to fit that purpose
ideally. The new driver only supports device tree probing for now.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some boards have this pin statically tied and do not require any configuration,
some other boards allow to enable chip using GPIO.
Add an option that tells which GPIO is used to power the audio codec.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has been functional and stable throughout the year it has spent
in the staging area. It has been patched for minor bugs, coding style issues
and improvements during this period.
This is the second submission of this move-out, after making several style
improvements, as suggested by Dan Carpenter.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge "Second Round of Renesas ARM Based SoC Clk Updates for v3.18" from Simon Horman.
* Add r8a7740, sh73a0 SoCs to MSTP bindings
* tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clk: shmobile: Add r8a7740, sh73a0 SoCs to MSTP bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap dts changes for v3.18 merge window" from Tony Lindgren:
Changes for .dts files for omaps for v3.18 merge window:
- Updates for gta04 to add gta04a3 model
- Add support for Tehnexion TAO3530 boards
- Regulator names for beaglebone
- Pinctrl related updates for omap5, dra7 and am437
- Model name fix for sbc-t54
- Enable mailbox for various omaps
* tag 'dt-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (291 commits)
ARM: dts: OMAP2+: Add sub mailboxes device node information
ARM: dts: dra7-evm: Mark uart1 rxd as wakeup capable
ARM: dts: OMAP5 / DRA7: switch over to interrupts-extended property for UART
ARM: dts: AM437x: switch to compatible pinctrl
ARM: dts: DRA7: switch to compatible pinctrl
ARM: dts: OMAP5: switch to compatible pinctrl
ARM: dts: am335x-boneblack: Add names for remaining regulators
ARM: dts: sbc-t54: fix model property
ARM: dts: omap5.dtsi: add DSS RFBI node
ARM: dts: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based)
ARM: dts: omap3: Add Technexion Thunder support (TAO3530 SOM based)
ARM: dts: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
ARM: OMAP2+: tao3530: Add pdata-quirk for the mmc2 internal clock
ARM: OMAP2+: board-generic: add support for AM57xx family
ARM: dts: dra72-evm: Add tps65917 PMIC node
ARM: dts: dra72-evm: Enable I2C1 node
Linux 3.17-rc3
unicore32: Fix build error
vexpress/spc: fix a build warning on array bounds
spi: sh-msiof: Fix transmit-only DMA transfers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Mailbox related changes for omaps to get it to work with
device tree.
* tag 'mailbox-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mailbox/omap: add support for parsing dt devices
Documentation: dt: add omap mailbox bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap intc changes for v3.18 merge window" from Tony Lindgren:
Interrupt code related clean-up for omap2 and 3 to make
it ready to move to drivers/irqchip. Note that this series
does not yet move the interrupt code to drivers, that will
be posted separately as a follow-up series.
Note that this branch has a dependency to patches both
in fixes-v3.18-not-urgent and soc-for-v3.18 and is based on
a merge. Without doing the merge, off-idle would not work
properly for git bisect.
* tag 'intc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (325 commits)
arm: omap: intc: switch over to linear irq domain
arm: omap: irq: get rid of ifdef hack
arm: omap: irq: introduce omap_nr_pending
arm: omap: irq: remove nr_irqs argument
arm: omap: irq: remove unnecessary header
arm: omap: irq: drop omap2_intc_handle_irq()
arm: omap: irq: drop omap3_intc_handle_irq()
arm: omap: irq: call set_handle_irq() from .init_irq
arm: omap: irq: move some more code around
arm: boot: dts: omap2/3/am33xx: drop ti,intc-size
arm: omap: irq: drop ti,intc-size support
arm: boot: dts: am33xx/omap3: fix intc compatible flag
arm: omap: irq: use compatible flag to figure out number of IRQ lines
arm: omap: irq: add specific compatibles for omap3 and am33xx devices
arm: omap: irq: drop .handle_irq and .init_irq fields
arm: omap: irq: use IRQCHIP_DECLARE macro
arm: omap: irq: call set_handle_irq() from intc_of_init
arm: omap: irq: make intc_of_init static
arm: omap: irq: reorganize code a little bit
arm: omap: irq: always define omap3 support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch documents the device tree bindings required for
the ohci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch documents the device tree bindings required for the
ehci on-chip controller found in ST consumer electronics SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TPL (Targeted Peripheral List) is needed for targets host
(OTG and Embedded Hosts) for usb certification and other
vendor specific requirements.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
St21nfcb has a reverse polarity compare to st21nfca.
In st21nfcb case, the irq pin is active high.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding for Qualcomm AHCI SATA controller and specifically
the sata controller on the IPQ806x family of SoCs.
We can utilize the "generic-ahci" platform driver with the addition of the
sata phy to enable SATA support on Qualcomm SoCs with AHCI controllers.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* pci/host-designware:
PCI: designware: Fold struct pcie_port_info into struct pcie_port
* pci/host-imx6:
PCI: imx6: Delay enabling reference clock for SS until it stabilizes
* pci/host-keystone:
PCI: keystone: Set device ID based on SoC to support multiple ports
PCI: keystone: Assume controller is already in RC mode
PCI: keystone: Limit MRSS for all downstream devices
* pci/host-tegra:
PCI: tegra: Add Tegra124 support
PCI: tegra: Make sure the PCIe PLL is really reset
PCI: tegra: Fix extended configuration space mapping
PCI: tegra: Clear CLKREQ# enable on port disable
* pci/host-xilinx:
PCI: xilinx: Fix xilinx_pcie_assign_msi() return value test
To get more comprehensive and integrated thermal management, it adds ntc
thermistor to thermal framework as a thermal sensor. It's governed thermal
susbsystem only if it is described in DT node. Otherwise, it just notifies
temperature to userspace via sysfs as it used to be.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Previously, the only way to map a NOR device as a simple ROM was to
use the obsolete "direct-mapped" compatible binding (which further
requires device_type = "nor" and probe-type = "NOR" properties).
This patch adds an "mtd-rom" compatible binding to the "map_rom"
probe type.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We want the fixes in there, and it resolves a merge issue with
drivers/iio/accel/bma180.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces generic code to perform PM domain look-up using
device tree and automatically bind devices to their PM domains.
Generic device tree bindings are introduced to specify PM domains of
devices in their device tree nodes.
Backwards compatibility with legacy Samsung-specific PM domain bindings
is provided, but for now the new code is not compiled when
CONFIG_ARCH_EXYNOS is selected to avoid collision with legacy code.
This will change as soon as the Exynos PM domain code gets converted to
use the generic framework in further patch.
This patch was originally submitted by Tomasz Figa when he was employed
by Samsung.
Link: http://marc.info/?l=linux-pm&m=139955349702152&w=2
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Document the new compatible for clock in DMC (Dynamic Memory
Controller) domain of Exynos3250 Clock Management Unit (CMU).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
