There is no point in warning when there is no ucode available
for a specific CPU revision. Currently the container-file, which
provides the AMD ucode patches for OS load, contains only a few
ucode patches.
It's already clearly indicated by the printed patch_level
whenever new ucode was available and an update happened. So the
warning message is of no help but rather annoying on systems
with many CPUs.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: dimm <dmitry.adamushko@gmail.com>
LKML-Reference: <20091110110825.GI30802@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the broken a.out format dump. For now we only dump the ptrace
breakpoints.
TODO: Dump every perf breakpoints for the current thread, not only
ptrace based ones.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: "K. Prasad" <prasad@linux.vnet.ibm.com>
On platforms where the BIOS handles the thermal monitor interrupt,
APIC_LVTTHMR on each logical CPU is programmed to generate a SMI
and OS must not touch it.
Unfortunately AP bringup sequence using INIT-SIPI-SIPI clears all
the LVT entries except the mask bit. Essentially this results in
all LVT entries including the thermal monitoring interrupt set
to masked (clearing the bios programmed value for APIC_LVTTHMR).
And this leads to kernel take over the thermal monitoring
interrupt on AP's but not on BSP (leaving the bios programmed
value only on BSP).
As a result of this, we have seen system hangs when the thermal
monitoring interrupt is generated.
Fix this by reading the initial value of thermal LVT entry on
BSP and if bios has taken over the control, then program the
same value on all AP's and leave the thermal monitoring
interrupt control on all the logical cpu's to the bios.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20091110013824.GA24940@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
We should not use physid_mask_t as a stack based
variable in apic code. This type depends on MAX_APICS
parameter which may be huge enough.
Especially it became a problem with apic NOOP driver which
is portable between 32 bit and 64 bit environment
(where we have really huge MAX_APICS).
So apic driver should operate with pointers and a caller
in turn should aware of allocation physid_mask_t variable.
As a side (but positive) effect -- we may use already
implemented physid_set_mask_of_physid function eliminating
default_apicid_to_cpu_present completely.
Note that physids_coerce and physids_promote turned into static
inline from macro (since macro hides the fact that parameter is
being interpreted as unsigned long, make it explicit).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20091109220659.GA5568@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In fact it's never get used on x86-64 (for 64 bit platform
we use differ technique to enumerate io-units).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20091108131645.GD5300@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should be ready that one day MAX_IO_APICS may raise its
number. To prevent memory overwrite we're to use safe
snprintf while set IO-APIC resourse name.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091108155431.GC25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The whole page is reserved for IO-APIC fixmap
due to non-cacheable requirement. So lets note
this explicitly instead of playing with numbers.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091108155356.GB25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rather than forcing GFP flags and DMA mask to be inconsistent,
GFP flags should be determined even for the fallback device
through dma_alloc_coherent_mask()/dma_alloc_coherent_gfp_flags().
This restores 64-bit behavior as it was prior to commits
8965eb1938 and
4a367f3a9d (not sure why there are
two of them), where GFP_DMA was forced on for 32-bit, but not
for 64-bit, with the slight adjustment that afaict even 32-bit
doesn't need this without CONFIG_ISA.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
LKML-Reference: <4AF18187020000780001D8AA@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch rebase the implementation of the breakpoints API on top of
perf events instances.
Each breakpoints are now perf events that handle the
register scheduling, thread/cpu attachment, etc..
The new layering is now made as follows:
ptrace kgdb ftrace perf syscall
\ | / /
\ | / /
/
Core breakpoint API /
/
| /
| /
Breakpoints perf events
|
|
Breakpoints PMU ---- Debug Register constraints handling
(Part of core breakpoint API)
|
|
Hardware debug registers
Reasons of this rewrite:
- Use the centralized/optimized pmu registers scheduling,
implying an easier arch integration
- More powerful register handling: perf attributes (pinned/flexible
events, exclusive/non-exclusive, tunable period, etc...)
Impact:
- New perf ABI: the hardware breakpoints counters
- Ptrace breakpoints setting remains tricky and still needs some per
thread breakpoints references.
Todo (in the order):
- Support breakpoints perf counter events for perf tools (ie: implement
perf_bpcounter_event())
- Support from perf tools
Changes in v2:
- Follow the perf "event " rename
- The ptrace regression have been fixed (ptrace breakpoint perf events
weren't released when a task ended)
- Drop the struct hw_breakpoint and store generic fields in
perf_event_attr.
- Separate core and arch specific headers, drop
asm-generic/hw_breakpoint.h and create linux/hw_breakpoint.h
- Use new generic len/type for breakpoint
- Handle off case: when breakpoints api is not supported by an arch
Changes in v3:
- Fix broken CONFIG_KVM, we need to propagate the breakpoint api
changes to kvm when we exit the guest and restore the bp registers
to the host.
Changes in v4:
- Drop the hw_breakpoint_restore() stub as it is only used by KVM
- EXPORT_SYMBOL_GPL hw_breakpoint_restore() as KVM can be built as a
module
- Restore the breakpoints unconditionally on kvm guest exit:
TIF_DEBUG_THREAD doesn't anymore cover every cases of running
breakpoints and vcpu->arch.switch_db_regs might not always be
set when the guest used debug registers.
(Waiting for a reliable optimization)
Changes in v5:
- Split-up the asm-generic/hw-breakpoint.h moving to
linux/hw_breakpoint.h into a separate patch
- Optimize the breakpoints restoring while switching from kvm guest
to host. We only want to restore the state if we have active
breakpoints to the host, otherwise we don't care about messed-up
address registers.
- Add asm/hw_breakpoint.h to Kbuild
- Fix bad breakpoint type in trace_selftest.c
Changes in v6:
- Fix wrong header inclusion in trace.h (triggered a build
error with CONFIG_FTRACE_SELFTEST
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kiszka <jan.kiszka@web.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
This patch cleans up pci_iommu_shutdown() a bit to use
x86_platform (similar to how IA64 initializes an IOMMU driver).
This adds iommu_shutdown() to x86_platform to avoid calling
every IOMMUs' shutdown functions in pci_iommu_shutdown() in
order. The IOMMU shutdown functions are platform specific (we
don't have multiple different IOMMU hardware) so the current way
is pointless.
An IOMMU driver sets x86_platform.iommu_shutdown to the shutdown
function if necessary.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: joerg.roedel@amd.com
LKML-Reference: <20091027163358F.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes two issues in the procfs stack information on
x86-64 linux.
The 32 bit loader compat_do_execve did not store stack
start. (this was figured out by Alexey Dobriyan).
The stack information on a x64_64 kernel always shows 0 kbyte
stack usage, because of a missing implementation of the KSTK_ESP
macro which always returned -1.
The new implementation now returns the right value.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1257240160.4889.24.camel@wall-e>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo wants the certainty of a static cpumask (rather than a
cpumask_var_t), but cpumask_t will some day be undefined to
avoid on-stack declarations.
This is what DECLARE_BITMAP/to_cpumask() is for.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <200911031453.52394.rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
tools/perf/Makefile
Merge reason: Resolve the conflict, merge to upstream and merge in
perf fixes so we can add a dependent patch.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
flush_thread() tries to do a TIF_DEBUG check before calling in to
flush_thread_hw_breakpoint() (which subsequently clears the thread flag),
but for some reason, the x86 code is manually clearing TIF_DEBUG
immediately before the test, so this path will never be taken.
This kills off the erroneous clear_tsk_thread_flag() and lets
flush_thread_hw_breakpoint() actually get invoked.
Presumably folks were getting lucky with testing and the
free_thread_info() -> free_thread_xstate() path was taking care of the
flush there.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: "K.Prasad" <prasad@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Alan Stern <stern@rowland.harvard.edu>
LKML-Reference: <20091005102306.GA7889@linux-sh.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
show_regs() is called as a mini BUG() equivalent in some places,
specifically for the "scheduling while atomic" case.
Unfortunately right now it does not print a Code: line unlike
a real bug/oops.
This patch changes the x86 implementation of show_regs() so that
it calls the same function as oopses do to print the registers
as well as the Code: line.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20091102165915.4a980fc0@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To ensure that we handle all the pending interrupts (destined
for this cpu that is going down) in the interrupt subsystem
before the cpu goes offline, fixup_irqs() does:
local_irq_enable();
mdelay(1);
local_irq_disable();
Enabling interrupts is not a good thing as this cpu is already
offline. So this patch replaces that logic with,
mdelay(1);
check APIC_IRR bits
Retrigger the irq at the new destination if any interrupt has arrived
via IPI.
For IO-APIC level triggered interrupts, this retrigger IPI will
appear as an edge interrupt. ack_apic_level() will detect this
condition and IO-APIC RTE's remoteIRR is cleared using directed
EOI(using IO-APIC EOI register) on Intel platforms and for
others it uses the existing mask+edge logic followed by
unmask+level.
We can also remove mdelay() and then send spuriuous interrupts
to new cpu targets for all the irqs that were handled previously
by this cpu that is going offline. While it works, I have seen
spurious interrupt messages (nothing wrong but still annoying
messages during cpu offline, which can be seen during
suspend/resume etc)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230002.043281924@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a cpu goes offline, fixup_irqs() try to move irq's
currently destined to the offline cpu to a new cpu. But this
attempt will fail if the irq is recently moved to this cpu and
the irq still hasn't arrived at this cpu (for non intr-remapping
platforms this is when we free the vector allocation at the
previous destination) that is about to go offline.
This will endup with the interrupt subsystem still pointing the
irq to the offline cpu, causing that irq to not work any more.
Fix this by forcing the irq to complete its move (its been a
long time we moved the irq to this cpu which we are offlining
now) and then move this irq to a new cpu before this cpu goes
offline.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.848830905@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_cleanup_count for each irq in irq_cfg is keeping track of
the total number of cpus that need to free the corresponding
vectors associated with the irq which has now been migrated to
new destination. As long as this move_cleanup_count is non-zero
(i.e., as long as we have n't freed the vector allocations on
the old destinations) we were preventing the irq's further
migration.
This cleanup count is unnecessary and it is enough to not allow
the irq migration till we send the cleanup vector to the
previous irq destination, for which we already have irq_cfg's
move_in_progress. All we need to make sure is that we free the
vector at the old desintation but we don't need to wait till
that gets freed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.752968906@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the presence of interrupt-remapping, irqs will be migrated in
the process context and we don't do (and there is no need to)
irq_chip mask/unmask while migrating the interrupt.
Similarly fix the fixup_irqs() that get called during cpu
offline and avoid calling irq_chip mask/unmask for irqs that are
ok to be migrated in the process context.
While we didn't observe any race condition with the existing
code, this change takes complete advantage of
interrupt-remapping in the newer generation platforms and avoids
any potential HW lockup's (that often worry Eric :)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: garyhade@us.ibm.com
LKML-Reference: <20091026230001.661423939@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reboot does not work out of the box on my "Early 2009" Mac mini
(3,1). Detect this machine via DMI as we do for recent MacBooks.
Signed-off-by: Gottfried Haider <gottfried.haider@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function iommu_feature_disable is required on system
shutdown to disable the IOMMU but it is marked as __init.
This may result in a panic if the memory is reused. This
patch fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Commit a98f8fd24f (x86: apic reset
counter on shutdown) set the counter to max to avoid spurious
interrupts when the timer is re-enabled.
(In theory) you'll still get a spurious interrupt if spending
more than 344 seconds with this interrupt disabled and then
unmasking it.
The right thing to do is to clear the register. This disables
the interrupt from happening (at least it does on AMD hardware).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20091027100138.GB30802@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The EFI RTC functions are only available on 32 bit. commit 7bd867df
(x86: Move get/set_wallclock to x86_platform_ops) removed the 32bit
dependency which leads to boot crashes on 64bit EFI systems.
Add the dependency back.
Solves: http://bugzilla.kernel.org/show_bug.cgi?id=14466
Tested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <20091020125402.028d66d5@feng-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Non-PAE 32-bit dump kernels may wrap an address around 4G and
poke unwanted space. ptes there are 32-bit long, and since
pfn << PAGE_SIZE may exceed this limit, high pfn bits are
cropped and wrong address mapped by kmap_atomic_pfn in
copy_oldmem_page.
Don't allow this behavior in non-PAE kdump kernels by checking
pfns passed into copy_oldmem_page. In the case of failure,
userspace process gets EFAULT.
[v2]
- fix comments
- move ifdefs inside the function
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Paul Mundt <lethal@linux-sh.org>
LKML-Reference: <1256551903-30567-1-git-send-email-jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
tools/perf/Makefile
Merge reason:
- fix the conflict
- pick up the pr_*() infrastructure to queue up dependent patch
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a comment explaining why RODATA is aligned to 2 MB.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CONFIG_DEBUG_RODATA chops the large pages spanning boundaries of kernel
text/rodata/data to small 4KB pages as they are mapped with different
attributes (text as RO, RODATA as RO and NX etc).
On x86_64, preserve the large page mappings for kernel text/rodata/data
boundaries when CONFIG_DEBUG_RODATA is enabled. This is done by allowing the
RODATA section to be hugepage aligned and having same RWX attributes
for the 2MB page boundaries
Extra Memory pages padding the sections will be freed during the end of the boot
and the kernel identity mappings will have different RWX permissions compared to
the kernel text mappings.
Kernel identity mappings to these physical pages will be mapped with smaller
pages but large page mappings are still retained for kernel text,rodata,data
mappings.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20091014220254.190119924@sbs-t61.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the first 2MB, kernel text is co-located with kernel static
page tables setup by head_64.S. CONFIG_DEBUG_RODATA chops this
2MB large page mapping to small 4KB pages as we mark the kernel text as RO,
leaving the static page tables as RW.
With CONFIG_DEBUG_RODATA disabled, OLTP run on NHM-EP shows 1% improvement
with 2% reduction in system time and 1% improvement in iowait idle time.
To recover this, move the kernel static page tables to .data section, so that
we don't have to break the first 2MB of kernel text to small pages with
CONFIG_DEBUG_RODATA.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20091014220254.063193621@sbs-t61.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Conflicts:
kernel/Makefile
kernel/trace/Makefile
kernel/trace/trace.h
samples/Makefile
Merge reason: We need to be uptodate with the perf events development
branch because we plan to rewrite the breakpoints API on top of
perf events.
Create an inline function to extract the pnode from a global
physical address and then convert the broadcast assist unit to
use the newly created uv_gpa_to_pnode function.
The open-coded code was wrong as well - it might explain a
few of our unexplained bau hangs.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Cliff Whickman <cpw@sgi.com>
Cc: linux-mm@kvack.org
Cc: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20091016112920.GZ8903@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prefix global/setup routines with "mcheck_" thus differentiating
from the internal facilities prefixed with "mce_". Also, prefix
the per cpu calls with mcheck_cpu and rename them to reflect the
MCE setup hierarchy of calls better.
There should be no functionality change resulting from this
patch.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <1255689093-26921-1-git-send-email-borislav.petkov@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
