Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.
This will optimize the download firmware time cost.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.
The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unless we sleep for a while before transitioning the MSA memory to WLAN
the MPSS.AT.4.0.c2-01184-SDM845_GEN_PACK-1 firmware triggers a security
violation fairly reliably. Unforutnately recovering from this failure
always results in the entire system freezing.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 334f5b61a6.
This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:
err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219
Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all files to add SPDX license identifiers and
remove license text.
This is only an administrative change, there is no change
in actual license or copyright for any file.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The `ar_usb` field of `ath10k_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath10k_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath10k_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath10k_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath10k_usb_alloc_urb_from_pipe` and
`ath10k_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref.
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Add driver tag to subject, fix build warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(kvalo: cherry picked from commit 1340cc631b in
wireless-drivers-next to wireless-drivers as this a frequently reported
regression)
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Regulatory rule defines in regd.c are used not only by ath9k but also
ath10k driver (haven't test other drivers) and thus should be
renamed from ATH9K* to ATH*.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The memory of ar->debug.tpc_stats_final is reallocated every debugfs
reading, it should be freed in ath10k_debug_destroy() for the last
allocation.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX)
or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds
access, so print a warning and reset to avoid memory corruption.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when pointer crash_data is null the present null check
will also check that crash_data->ramdump_buf is null and will cause
a null pointer dereference on crash_data. Fix this by using the ||
operator instead of &&.
Fixes: 3f14b73c38 ("ath10k: Enable MSA region dump support for WCN3990")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all data packets transmitted, host gets htt tx completion event. Some QCA9984
firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data
ack rssi values to host through htt event of data tx completion. Data ack rssi
values are valid if A0 bit is set in HTT rx message. So enable the feature also
for QCA9884.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[kvalo@codeaurora.org: improve commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
memcpy() in wmi_set_ie() and wmi_update_ft_ies() is called with
src == NULL and len == 0. This is an undefined behavior. Fix it
by checking "ie_len > 0" before the memcpy() calls.
As suggested by GCC documentation:
"The pointers passed to memmove (and similar functions in <string.h>)
must be non-null even when nbytes==0, so GCC can use that information
to remove the check after the memmove call." [1]
[1] https://gcc.gnu.org/gcc-4.9/porting_to.html
Cc: Maya Erez <merez@codeaurora.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memcpy() call with "idata == NULL && ilen == 0" results in undefined
behavior in ar5523_cmd(). For example, NULL is passed in callchain
"ar5523_stat_work() -> ar5523_cmd_write() -> ar5523_cmd()". This patch
adds ilen check before memcpy() call in ar5523_cmd() to prevent an
undefined behavior.
Cc: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
Cc: stable@vger.kernel.org
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, data variable in ar9003_hw_thermo_cal_apply() could be
uninitialized if ar9300_otp_read_word() will fail to read the value.
Initialize data variable with 0 to prevent an undefined behavior. This
will be enough to handle error case when ar9300_otp_read_word() fails.
Fixes: 80fe43f2bb ("ath9k_hw: Read and configure thermocal for AR9462")
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IRAM start address in coredump was wrong for QCA9984, QCA4019, QCA9888 and
QCA99x0.
Tested on: QCA9984, QCA4019
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Software version within WMI event ready message was displayed
in a not very useful decimal format. Change this info to be shown
in a hexadecimal format instead.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Displays lowest/highest supported channels for both 2ghz and 5ghz
bands as they're fetched within WMI service ready event.
These are shown in a frequency format.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
