It can happen that on IRQ trigger, not all conversions are done if
we are enabling multiple channels.
The IRQ is triggered on first EOC (end of channel), but it can happen
that not all channels are done. This leads into erroneous reports to
userspace (zero values or previous values).
To solve this, in trigger handler, check if the mask of done channels
is the same as the mask of active scan channels.
If it's the same, proceed and push to buffers. Otherwise, use usleep
to sleep until the conversion is done or we timeout.
Normally, it should happen that in a short time fashion, all channels are
ready, since the first IRQ triggered.
If a hardware fault happens (for example the clock suddently dissappears),
the handler will not be completed, in which case we do not report anything to
userspace anymore.
Also, change from using the EOC interrupts to DRDY interrupt.
This helps with the fact that not 'n' interrupt statuses are enabled,
each being able to trigger an interrupt, and instead only data ready
interrupt can wake up the CPU. Like this, when data is ready, check in
handler which and how many channels are done. While the DRDY is raised,
other IRQs cannot occur. Once the channel data is being read, we ack the
IRQ and finish the conversion.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together. Reduces boilerplate and suggested
by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.
Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change uses the read_avail and '.info_mask_shared_by_type_available'
modifier to set the available scale.
Essentially, nothing changes to the driver's ABI.
The main idea for this patch is to remove the AD7793 driver from
checkpatch's radar. There have been about ~3 attempts to fix/break the
'in_voltage-voltage_scale_available' attribute, because checkpatch assumed
it to be an arithmetic operation and people were trying to change that.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver seems to use most of the AD_SD_*_CHANNEL. This change will move
them in the driver. The intent is that if a new part comes along which
would require tweaks per IIO channel, these should be doable in the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver seems to use most of the AD_SD_*_CHANNEL. This change will move
them in the driver. The intent is that if a new part comes along which
would require tweaks per IIO channel, these should be doable in the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change gets rid of the AD_SD_*_CHANNEL macros in favor of defining
it's own. The ad7780 is quite simpler than it's other Sigma-Delta brothers.
It turned out that centralizing the AD_SD_*_CHANNEL macros doesn't scale
too well, especially with some more complicated drivers. Some of the
variations in the more complicated drivers require new macros, and that way
things can become harder to maintain.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b9128 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to automatically disable the device
when it is removed or an error occurs during probe routine.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7091R is already supported by this driver. While AD7091R allows the
choice of an internal or an external voltage reference, for AD7091 the
reference is only provided by VDD. Since this information is anyway
obtained through the "vcc" regulator, no other driver changes are
required for adding AD7091 support as well.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When CONVST signal is generated internally, IIO_CHAN_INFO_RAW can be
made available for AD7091R for single reads. This patch enables it and
makes supporting more devices by this driver easier.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compared to the other supported parts, AD7091R are dependent of
a CONVST signal that initiates the conversion. At this moment, only
sampling in buffered mode is supported for AD7091R and the only
option until now was to generate this signal externally using an
IIO trigger. This patch adds the option of generating it internally,
more compatible triggers being available in this case.
Also, it is an intermediate step of adding support more devices.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to call unaligned helpers on stack placed variables
because compiler will align them correctly, accordingly to architectural
ABI. Moreover, using bitwise type makes it explicit to see what we are
reading in bulk transfer. On top of that, use sizeof() instead of
magic value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan writes:
First set of IIO fixes in the 5.6 cycle.
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
* tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ping: set pa_laser_ping_cfg in of_ping_match
iio: chemical: sps30: fix missing triggered buffer dependency
iio: st_sensors: remap SMO8840 to LIS2DH12
iio: light: vcnl4000: update sampling periods for vcnl4040
iio: light: vcnl4000: update sampling periods for vcnl4200
iio: accel: adxl372: Set iio_chan BE
iio: magnetometer: ak8974: Fix negative raw values in sysfs
iio: trigger: stm32-timer: disable master mode when stopping
iio: adc: stm32-dfsdm: fix sleep in atomic context
iio: adc: at91-sama5d2_adc: fix differential channels in triggered mode
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't confuse user with meaningless warning about the failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the posibility do read and write registers from userspace
using the kernel debug direct register access option.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Modify NPCM ADC reset support from
direct register access to reset controller support.
please make sure to modify NPCM adc device tree
parameters as described at nuvoton,npcm-adc.txt
document for using this change.
Note for anyone noting that this is a breaking change, this is on
a BMC and effectively in a close ecosystem so it is fine to rely
on DT and kernel being updated together.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the LOW_PASS_FILTER_3DB_FREQUENCY attribute
in iio_chan_spec for each channel. The used filters are sinc3
or sinc4. The filter type with the highest output data rate
is used when setting a low pass frequency in the channel's sysfs.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit fixes the error message:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
Suppress the trigger irq handler. Make the buffer transfers directly
in DMA callback, instead.
Push buffers without timestamps, as timestamps are not supported
in DFSDM driver.
Fixes: 11646e81d7 ("iio: adc: stm32-dfsdm: add support for buffer modes")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The differential channels require writing the channel offset register (COR).
Otherwise they do not work in differential mode.
The configuration of COR is missing in triggered mode.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ad7124 data-sheet specifies that the falling edge
of the DOUT line should be used for an interrupt.
The current irq flag (IRQF_TRIGGER_LOW) used will
cause unwanted behaviour. When enabling the interrupt
it will fire once because the DOUT line is already low.
This will make the driver to read an unfinished conversion
from the chip.
This patch sets the irq type to the one specified in
the data-sheet.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
