of_gpiochip_add(), when fails, calls gpiochip_remove_pin_ranges().
ADD:
gpiochip_add_data_with_key() ->
of_gpiochip_add() -> (ERROR path)
gpiochip_remove_pin_ranges()
At the same time of_gpiochip_remove() calls exactly the above mentioned
function unconditionally and so does gpiochip_remove().
REMOVE:
gpiochip_remove() ->
gpiochip_remove_pin_ranges()
of_gpiochip_remove() ->
gpiochip_remove_pin_ranges()
Since gpiochip_remove() calls gpiochip_remove_pin_ranges() unconditionally,
we have duplicate call to the same function when it's not necessary.
Move gpiochip_remove_pin_ranges() from of_gpiochip_add() to gpiochip_add()
to avoid duplicate calls and be consistent with the explicit call in
gpiochip_remove().
Fixes: e93fa3f243 ("gpiolib: remove duplicate pin range code")
Depends-on: f7299d441a ("gpio: of: Fix of_gpiochip_add() error path")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The table of devicetree identifiers is annotated as __initconst
indicating that it can be discarded after kernel boot but it is
referenced from the driver struct which has no init annotation leading
to a linker warning:
WARNING: vmlinux.o(.data+0x82d58): Section mismatch in reference from the variable bcm_iproc_gpio_driver to the variable .init.rodata:bcm_iproc_gpio_of_match
The variable bcm_iproc_gpio_driver references
the variable __initconst bcm_iproc_gpio_of_match
Since drivers can be probed after init the lack of annotation on the
driver struct is correct so remove the annotation from the match table.
Fixes: 6a41b6c5fc ("gpio: Add xgs-iproc driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8f86a5b4ad.
It has been established that this causes a boot regression on
both Baytrail and Cherrytrail SoCs, and we can't have that in
the final kernel release, so we need to revert it.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull in mips-fixes primarily to gain build fixes in order to allow
better testing of mips-next.
A few MIPS fixes:
- Fix VDSO time-related function behavior for systems where we need to
fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where they
would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address.
Signed-off-by: Paul Burton <paulburton@kernel.org>
gpio updates for v5.5
- only get the second IRQ when there is more than one IRQ in mxc
- move the code around in lineevent_create() for some shrinkage
- fix formatting for GPIO docs
- add DT binding for r8a774b1
- convert drivers that prevously used nocache ioremap() to using regular
devm_platform_ioremap_resource()
- remove some redundant error messages
- shrink object code in 104-idi-48e
- drop an unneeded warning from gpiolib-of
Some devicetrees specify the ACTIVE_LOW flag in the fixed regulator GPIO
handle. While this has always been ignored, it's consistent with the
behavior of the regulator binding in the absence of the
"enable-active-high" DT property. It doesn't make much sense to print a
user visible warning for a configuration which is consistent, so only
print the warning if the GPIO flag contradicts the behavior dictated by
by the enable-active-high property.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[Bartosz: coding style tweak]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
More than one gpio controllers can share one interrupt, change the
driver to request shared irq.
While this will work, it will mess up userspace accounting of the number
of interrupts per second in tools such as vmstat. The reason is that
for every GPIO interrupt, /proc/interrupts records the count against GIC
interrupt 68 or 69, as well as the GPIO itself. So, for every GPIO
interrupt, the total number of interrupts that the system has seen
increments by two.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Link: https://lore.kernel.org/r/20191011005643.41007-1-hui.song_1@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 7b1e889436 ("gpio: lynxpoint: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver wants to initialize related registers before IRQ chip will be added.
That's why move it to a corresponding callback. It also fixes the NULL pointer
dereference.
Fixes: 8069e69a97 ("gpio: intel-mid: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the drivers to use GPIO core to add an IRQ chip
it appears that some of them requires a hardware initialization
before adding the IRQ chip.
Add an optional callback ->init_hw() to allow that drivers
to initialize hardware if needed.
This change is a part of the fix NULL pointer dereference
brought to the several drivers recently.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During conversion to internal IRQ chip initialization the commit
8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
lost the irq_base assignment.
drivers/gpio/gpio-merrifield.c: In function ‘mrfld_gpio_probe’:
drivers/gpio/gpio-merrifield.c:405:17: warning: variable ‘irq_base’ set but not used [-Wunused-but-set-variable]
Assign the girq->first to it.
Fixes: 8f86a5b4ad ("gpio: merrifield: Pass irqchip when adding gpiochip")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Don't populate the array register_offset on the stack but instead make it
static. Makes the object code smaller by 63 bytes. Also add the int type
specifier to clean up a checkpatch warning.
Before:
text data bss dec hex filename
9212 5712 1408 16332 3fcc drivers/gpio/gpio-104-idi-48.o
After:
text data bss dec hex filename
9085 5776 1408 16269 3f8d drivers/gpio/gpio-104-idi-48.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error. Also: the driver currently drops info
about errors propagated from called functions by default to returning
-EINVAL. This fixes it as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to use the nocache variant of ioremap(). Switch to
using devm_platform_ioremap_resource().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There's no need to emit an error message on probe failure unless we're
printing some meaningful info. Otherwise the core driver code will
inform us about a probe error.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO controller doesn't have any controls to enable the system to
wake up from low power states based on activity on GPIO pins. An extra
hardware block that is part of the power management controller (PMC)
contains these controls. In order for the GPIO controller to be able
to cooperate with the PMC, obtain a reference to the PMC's IRQ domain
and make it a parent to the GPIO controller's IRQ domain. This way the
PMC gets an opportunity to program the additional registers required
to enable wakeup sources on suspend.
Based on additional work by Bitan Biswas <bbiswas@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002144502.156393-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt-related register fields on the MAX77620 GPIO controller
share registers with GPIO related fields. If the IRQ chip is implemented
with regmap-irq, this causes the IRQ controller code to overwrite fields
previously configured by the GPIO controller code.
Two examples where this causes problems are the NVIDIA Jetson TX1 and
Jetson TX2 boards, where some of the GPIOs are used to enable vital
power regulators. The MAX77620 GPIO controller also provides the USB OTG
ID pin. If configured as an interrupt, this causes some of the
regulators to be powered off.
Signed-off-by: Timo Alho <talho@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191002122825.3948322-3-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move all the flags sanitization before any memory allocation in
lineevent_create() in order to remove a couple unneeded gotos.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When toggling the level trigger to emulate the edge trigger, the
EIC offset is incorrect without adding the corresponding bank index,
thus fix it.
Fixes: 7bf0d7f622 ("gpio: eic: Add edge trigger emulation for EIC")
Cc: stable@vger.kernel.org
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since commit ec757001c8 ("gpio: Enable nonexclusive gpiods from DT
nodes") we are able to get GPIOD_FLAGS_BIT_NONEXCLUSIVE marked gpios.
Currently the gpiolib uses the wrong flags variable for the check. We
need to check the gpiod_flags instead of the of_gpio_flags else we
return -EBUSY for GPIOD_FLAGS_BIT_NONEXCLUSIVE marked and requested
gpiod's.
Fixes: ec757001c8 gpio: Enable nonexclusive gpiods from DT nodes
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[Bartosz: the function was moved to gpiolib-of.c so updated the patch]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When emulating open-drain/open-source by not actively driving the output
lines - we're simply changing their mode to input. This is wrong as it
will then make it impossible to change the value of such line - it's now
considered to actually be in input mode. If we want to still use the
direction_input() callback for simplicity then we need to set FLAG_IS_OUT
manually in gpiod_direction_output() and not clear it in
gpio_set_open_drain_value_commit() and
gpio_set_open_source_value_commit().
Fixes: c663e5f567 ("gpio: support native single-ended hardware drivers")
Cc: stable@vger.kernel.org
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
On some of i.MX SoCs like i.MX8QXP, there is ONLY one IRQ for each
GPIO bank, so it is better to check the IRQ count before getting
second IRQ to avoid below error message during probe:
[ 1.070908] gpio-mxc 5d080000.gpio: IRQ index 1 not found
[ 1.077420] gpio-mxc 5d090000.gpio: IRQ index 1 not found
[ 1.083766] gpio-mxc 5d0a0000.gpio: IRQ index 1 not found
[ 1.090122] gpio-mxc 5d0b0000.gpio: IRQ index 1 not found
[ 1.096470] gpio-mxc 5d0c0000.gpio: IRQ index 1 not found
[ 1.102804] gpio-mxc 5d0d0000.gpio: IRQ index 1 not found
[ 1.109144] gpio-mxc 5d0e0000.gpio: IRQ index 1 not found
[ 1.115475] gpio-mxc 5d0f0000.gpio: IRQ index 1 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This renames the "gpio-aspeed" driver to conform with other
GPIO drivers as "gpio-aspeed-sgpio.c". All GPIO drivers
should start with the string "gpio-" no special exceptions.
Also the Kconfig and Makefile entries should normally
go with the driver but I missed this in my review, sorry
for mistake. "CONFIG_GPIO_ASPEED_SGPIO" is used to
activate this driver.
Cc: Hongwei Zhang <hongweiz@ami.com>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190927114833.12551-1-linus.walleij@linaro.org
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
It is surprising for a PWM consumer when the variable holding the
requested state is modified by pwm_apply_state(). Consider for example a
driver doing:
#define PERIOD 5000000
#define DUTY_LITTLE 10
...
struct pwm_state state = {
.period = PERIOD,
.duty_cycle = DUTY_LITTLE,
.polarity = PWM_POLARITY_NORMAL,
.enabled = true,
};
pwm_apply_state(mypwm, &state);
...
state.duty_cycle = PERIOD / 2;
pwm_apply_state(mypwm, &state);
For sure the second call to pwm_apply_state() should still have
state.period = PERIOD and not something the hardware driver chose for a
reason that doesn't necessarily apply to the second call.
So declare the state argument as a pointer to a const type and adapt all
drivers' .apply callbacks.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
