Pull xen fix from Juergen Gross:
"One fix for a regression when booting as a Xen guest on ARM64
introduced probably during the 5.9 cycle. It is very low risk as it is
modifying Xen specific code only.
The exact commit introducing the bug hasn't been identified yet, but
everything was fine in 5.8 and only in 5.9 some configurations started
to fail"
* tag 'for-linus-5.9b-rc9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/arm64: xen: Fix to convert percpu address to gfn correctly
Pull power management fixes from Rafael Wysocki:
"These fix one more issue related to the recent RCU-lockdep changes, a
typo in documentation and add a missing return statement to
intel_pstate.
Specifics:
- Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf
Hansson)
- Fix typo in the PM documentation (Yoann Congal)
- Add return statement that is missing after recent changes in the
intel_pstate driver (Zhang Rui)"
* tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: imx6q: Fixup RCU usage for cpuidle
Documentation: PM: Fix a reStructuredText syntax error
cpufreq: intel_pstate: Fix missing return statement
The commit eb1f00237a ("lockdep,trace: Expose tracepoints"), started to
expose us for tracepoints. For imx6q cpuidle, this leads to an RCU splat
according to below.
[6.870684] [<c0db7690>] (_raw_spin_lock) from [<c011f6a4>] (imx6q_enter_wait+0x18/0x9c)
[6.878846] [<c011f6a4>] (imx6q_enter_wait) from [<c09abfb0>] (cpuidle_enter_state+0x168/0x5e4)
To fix the problem, let's assign the corresponding idlestate->flags the
CPUIDLE_FLAG_RCU_IDLE bit, which enables us to call rcu_idle_enter|exit()
at the proper point.
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull devicetree fixes from Rob Herring:
- Fix handling of HOST_EXTRACFLAGS for dtc
- Several warning fixes for DT bindings
* tag 'devicetree-fixes-for-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
scripts/dtc: only append to HOST_EXTRACFLAGS instead of overwriting
dt-bindings: Fix 'reg' size issues in zynqmp examples
ARM: dts: bcm2835: Change firmware compatible from simple-bus to simple-mfd
dt-bindings: leds: cznic,turris-omnia-leds: fix error in binding
dt-bindings: crypto: sa2ul: fix a DT binding check warning
The current binding for the RPi firmware uses the simple-bus compatible as
a fallback to benefit from its automatic probing of child nodes.
However, simple-bus also comes with some constraints, like having the ranges,
our case.
Let's switch to simple-mfd that provides the same probing logic without
those constraints.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200924082642.18144-1-maxime@cerno.tech
Signed-off-by: Rob Herring <robh@kernel.org>
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes I've been accruing over the last few weeks, none
of them have been severe enough to warrant flushing the queue but it's
been long enough now that it's a good idea to send them in.
A handful of them are fixups for QSPI DT/bindings/compatibles, some
smaller fixes for system DMA clock control and TMU interrupts on i.MX,
a handful of fixes for OMAP, including a fix for DSI (display) on
omap5"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (27 commits)
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
arm64: defconfig: Enable ptn5150 extcon driver
arm64: defconfig: Enable USB gadget with configfs
ARM: configs: Update Integrator defconfig
ARM: dts: omap5: Fix DSI base address and clocks
...
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.9, please pull the following:
- Florian fixes the Broadcom QSPI controller binding such that the most
specific compatible string is the left most one, and all existing
in-tree users are updated as well.
* tag 'arm-soc/for-5.9/devicetree-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: ns2: Fixed QSPI compatible string
ARM: dts: BCM5301X: Fixed QSPI compatible string
ARM: dts: NSP: Fixed QSPI compatible string
ARM: dts: bcm: HR2: Fixed QSPI compatible string
dt-bindings: spi: Fix spi-bcm-qspi compatible ordering
Link: https://lore.kernel.org/r/20200909211857.4144718-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 5.9, round 2:
- Fix the misspelling of 'interrupts' property in i.MX8MQ TMU DT node.
- Correct 'ahb' clock for i.MX8MP SDMA1 in device tree.
- Fix pad QSPI1B_SCLK mux mode for UART3 on i.MX6SX.
* tag 'imx-fixes-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix the pad QSPI1B_SCLK mux mode for uart3
arm64: dts: imx8mp: correct sdma1 clk setting
arm64: dts: imx8mq: Fix TMU interrupt property
Link: https://lore.kernel.org/r/20200909143844.GA25109@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v5.9-rc cycle
Few fixes for omap based devices:
- Fix of_clk_get() error handling for omap-iommu
- Fix missing audio pinctrl entries for logicpd boards
- Fix video for logicpd-som-lv after switch to generic panels
- Fix omap5 DSI clocks base
* tag 'omap-for-v5.9/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: Fix DSI base address and clocks
ARM: dts: logicpd-som-lv-baseboard: Fix missing video
ARM: dts: logicpd-som-lv-baseboard: Fix broken audio
ARM: dts: logicpd-torpedo-baseboard: Fix broken audio
ARM: OMAP2+: Fix an IS_ERR() vs NULL check in _get_pwrdm()
Link: https://lore.kernel.org/r/pull-1599132064-54898@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 1c8f406507 ("ARM: dts: BCM5301X: convert to iProc QSPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 329f98c197 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The pad QSPI1B_SCLK mux mode 0x1 is for function UART3_DTE_TX,
correct the mux mode.
Fixes: 743636f25f ("ARM: dts: imx: add pin function header for imx6sx")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull locking fixes from Thomas Gleixner:
"A set of fixes for lockdep, tracing and RCU:
- Prevent recursion by using raw_cpu_* operations
- Fixup the interrupt state in the cpu idle code to be consistent
- Push rcu_idle_enter/exit() invocations deeper into the idle path so
that the lock operations are inside the RCU watching sections
- Move trace_cpu_idle() into generic code so it's called before RCU
goes idle.
- Handle raw_local_irq* vs. local_irq* operations correctly
- Move the tracepoints out from under the lockdep recursion handling
which turned out to be fragile and inconsistent"
* tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep,trace: Expose tracepoints
lockdep: Only trace IRQ edges
mips: Implement arch_irqs_disabled()
arm64: Implement arch_irqs_disabled()
nds32: Implement arch_irqs_disabled()
locking/lockdep: Cleanup
x86/entry: Remove unused THUNKs
cpuidle: Move trace_cpu_idle() into generic code
cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic
sched,idle,rcu: Push rcu_idle deeper into the idle path
cpuidle: Fixup IRQ state
lockdep: Use raw_cpu_*() for per-cpu variables
i.MX fixes for 5.9:
- Fix QuadSPI-memory 'reg' for LS1021A and GPIO 'ranges' for i.MX7ULP
pinctrl.
- A couple of DTC warning fixes on imx6qdl-gw51xx and imx6q-prtwd2
boards.
- Add missing imx8mm-beacon-kit.dtb to dtbs-y for build coverage.
- Fix broken PWM settings on imx6q-logicpd board.
- Add missing syscon compatible to OCOTP device, so that access to UID
is possible.
- Fix a network regression on imx7d-zii-rmu2 due to a phy-mode mismatch.
* tag 'imx-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-zii-rmu2: fix rgmii phy-mode for ksz9031 phy
ARM: dts: vfxxx: Add syscon compatible with OCOTP
ARM: dts: imx6q-logicpd: Fix broken PWM
arm64: dts: imx: Add missing imx8mm-beacon-kit.dtb to build
ARM: dts: imx6q-prtwd2: Remove unneeded i2c unit name
ARM: dts: imx6qdl-gw51xx: Remove unneeded #address-cells/#size-cells
ARM: dts: imx7ulp: Correct gpio ranges
ARM: dts: ls1021a: fix QuadSPI-memory reg range
Link: https://lore.kernel.org/r/20200824130359.GF12776@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit bcf3440c6d ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on the imx7d-zii-rmu2 board.
The end result is that network receive behaviour is marginal with lots of
RX CRC errors experienced and NFS frequently failing.
Quoting the explanation from Andrew Lunn in commit 0672d22a19
("ARM: dts: imx: Fix the AR803X phy-mode"):
"The problem here is, all the DTs were broken since day 0. However,
because the PHY driver was also broken, nobody noticed and it
worked. Now that the PHY driver has been fixed, all the bugs in the
DTs now become an issue"
Fix it by switching to phy-mode = "rgmii-id".
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DTC doesn't like the default PWM settings, because it's expecting
three cells. This patch reduces adds the extra entry of 0 to the PWM
reference.
Fixes: fa28d8212e ("ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6q-prtwd2.dts:33.8-43.4: Warning (unit_address_vs_reg): /i2c@4: node has a unit name, but no reg or ranges property
Remove the unneeded i2c unit name to fix the issue.
Fixes: 88010b8174 ("ARM: dts: add Protonic WD2 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc warning is seen when building with W=1:
arch/arm/boot/dts/imx6qdl-gw51xx.dtsi:23.12-68.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unneeded #address-cells/#size-cells properties to fix the issue.
Fixes: 64bf0a0af1 ("ARM: dts: imx6qdl-gw: add Gateworks System Controller support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct gpio ranges according to i.MX7ULP pinctrl driver:
gpio_ptc: ONLY pin 0~19 are available;
gpio_ptd: ONLY pin 0~11 are available;
gpio_pte: ONLY pin 0~15 are available;
gpio_ptf: ONLY pin 0~19 are available;
Fixes: 20434dc92c ("ARM: dts: imx: add common imx7ulp dtsi support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the Reference Manual, the correct size is 512 MiB.
Without this fix, probing the QSPI fails:
fsl-quadspi 1550000.spi: ioremap failed for resource
[mem 0x40000000-0x7fffffff]
fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
fsl-quadspi: probe of 1550000.spi failed with error -12
Fixes: 85f8ee78ab ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the Integrator defconfig to the changes from the recent
kernel cycles and especially the v5.9-rc1 changes.
- Move options around as a result of Kconfig changes.
- Drop the ZBOOT_ROM* stuff that doesn't exist anymore.
- Select GPIO input and evdev as used by the pushbuttons
on the machine.
- Select CONFIG_DRM_DISPLAY_CONNECTOR=y, the
CONFIG_DRM_SIMPLE_BRIDGE was renamed when renaming the
driver, but the simple bridge requires another bridge,
the display connector bridge, in order to work, so this
is required to have graphics working properly in kernel
v5.9-rc1+
Link: https://lore.kernel.org/r/20200820085752.42994-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
DSI was not probing due to base address off by 0x1000, and sys_clk
missing.
With this patch, the Pyra display works if HDMI is disabled in the
device tree.
Fixes: 5a507162f0 ("ARM: dts: Configure interconnect target module for omap5 dsi1")
Signed-off-by: David Shah <dave@ds0.me>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
[tony@atomide.com: standardized subject line, added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the register address for the timer3 entry on Arria10.
Fixes: 475dc86d08 ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
A previous commit removed the panel-dpi driver, which made the
SOM-LV video stop working because it relied on the DPI driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the SOM-LV dev kits
to use a similar panel and remove the manual timing requirements.
A similar patch was already done and applied to the Torpedo family.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 5cb8b0fa55 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.
Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.
This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.
Fixes: 739f85bba5 ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The of_clk_get() function returns error pointers, it never returns NULL.
Fixes: 4ea3711aec ("ARM: OMAP2+: omap-iommu.c conversion to ti-sysc")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull timekeeping updates from Thomas Gleixner:
"A set of timekeeping/VDSO updates:
- Preparatory work to allow S390 to switch over to the generic VDSO
implementation.
S390 requires that the VDSO data pointer is handed in to the
counter read function when time namespace support is enabled.
Adding the pointer is a NOOP for all other architectures because
the compiler is supposed to optimize that out when it is unused in
the architecture specific inline. The change also solved a similar
problem for MIPS which fortunately has time namespaces not yet
enabled.
S390 needs to update clock related VDSO data independent of the
timekeeping updates. This was solved so far with yet another
sequence counter in the S390 implementation. A better solution is
to utilize the already existing VDSO sequence count for this. The
core code now exposes helper functions which allow to serialize
against the timekeeper code and against concurrent readers.
S390 needs extra data for their clock readout function. The initial
common VDSO data structure did not provide a way to add that. It
now has an embedded architecture specific struct embedded which
defaults to an empty struct.
Doing this now avoids tree dependencies and conflicts post rc1 and
allows all other architectures which work on generic VDSO support
to work from a common upstream base.
- A trivial comment fix"
* tag 'timers-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Delete repeated words in comments
lib/vdso: Allow to add architecture-specific vdso data
timekeeping/vsyscall: Provide vdso_update_begin/end()
vdso/treewide: Add vdso_data pointer argument to __arch_get_hw_counter()
Merge more updates from Andrew Morton:
- most of the rest of MM (memcg, hugetlb, vmscan, proc, compaction,
mempolicy, oom-kill, hugetlbfs, migration, thp, cma, util,
memory-hotplug, cleanups, uaccess, migration, gup, pagemap),
- various other subsystems (alpha, misc, sparse, bitmap, lib, bitops,
checkpatch, autofs, minix, nilfs, ufs, fat, signals, kmod, coredump,
exec, kdump, rapidio, panic, kcov, kgdb, ipc).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
mm/gup: remove task_struct pointer for all gup code
mm: clean up the last pieces of page fault accountings
mm/xtensa: use general page fault accounting
mm/x86: use general page fault accounting
mm/sparc64: use general page fault accounting
mm/sparc32: use general page fault accounting
mm/sh: use general page fault accounting
mm/s390: use general page fault accounting
mm/riscv: use general page fault accounting
mm/powerpc: use general page fault accounting
mm/parisc: use general page fault accounting
mm/openrisc: use general page fault accounting
mm/nios2: use general page fault accounting
mm/nds32: use general page fault accounting
mm/mips: use general page fault accounting
mm/microblaze: use general page fault accounting
mm/m68k: use general page fault accounting
mm/ia64: use general page fault accounting
mm/hexagon: use general page fault accounting
mm/csky: use general page fault accounting
...
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
Pull Kbuild updates from Masahiro Yamada:
- run the checker (e.g. sparse) after the compiler
- remove unneeded cc-option tests for old compiler flags
- fix tar-pkg to install dtbs
- introduce ccflags-remove-y and asflags-remove-y syntax
- allow to trace functions in sub-directories of lib/
- introduce hostprogs-always-y and userprogs-always-y syntax
- various Makefile cleanups
* tag 'kbuild-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: stop filtering out $(GCC_PLUGINS_CFLAGS) from cc-option base
kbuild: include scripts/Makefile.* only when relevant CONFIG is enabled
kbuild: introduce hostprogs-always-y and userprogs-always-y
kbuild: sort hostprogs before passing it to ifneq
kbuild: move host .so build rules to scripts/gcc-plugins/Makefile
kbuild: Replace HTTP links with HTTPS ones
kbuild: trace functions in subdirectories of lib/
kbuild: introduce ccflags-remove-y and asflags-remove-y
kbuild: do not export LDFLAGS_vmlinux
kbuild: always create directories of targets
powerpc/boot: add DTB to 'targets'
kbuild: buildtar: add dtbs support
kbuild: remove cc-option test of -ffreestanding
kbuild: remove cc-option test of -fno-stack-protector
Revert "kbuild: Create directory for target DTB"
kbuild: run the checker after the compiler
Pull regset conversion fix from Al Viro:
"Fix a regression from an unnoticed bisect hazard in the regset series.
A bunch of old (aout, originally) primitives used by coredumps became
dead code after fdpic conversion to regsets. Removal of that dead code
had been the first commit in the followups to regset series;
unfortunately, it happened to hide the bisect hazard on sh (extern for
fpregs_get() had not been updated in the main series when it should
have been; followup simply made fpregs_get() static). And without that
followup commit this bisect hazard became breakage in the mainline"
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill unused dump_fpu() instances
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
CFLAGS_REMOVE_<file>.o filters out flags when compiling a particular
object, but there is no convenient way to do that for every object in
a directory.
Add ccflags-remove-y and asflags-remove-y to make it easily.
Use ccflags-remove-y to clean up some Makefiles.
The add/remove order works as follows:
[1] KBUILD_CFLAGS specifies compiler flags used globally
[2] ccflags-y adds compiler flags for all objects in the
current Makefile
[3] ccflags-remove-y removes compiler flags for all objects in the
current Makefile (New feature)
[4] CFLAGS_<file> adds compiler flags per file.
[5] CFLAGS_REMOVE_<file> removes compiler flags per file.
Having [3] before [4] allows us to remove flags from most (but not all)
objects in the current Makefile.
For example, kernel/trace/Makefile removes $(CC_FLAGS_FTRACE)
from all objects in the directory, then adds it back to
trace_selftest_dynamic.o and CFLAGS_trace_kprobe_selftest.o
The same applies to lib/livepatch/Makefile.
Please note ccflags-remove-y has no effect to the sub-directories.
In contrast, the previous notation got rid of compiler flags also from
all the sub-directories.
The following are not affected because they have no sub-directories:
arch/arm/boot/compressed/
arch/powerpc/xmon/
arch/sh/
kernel/trace/
However, lib/ has several sub-directories.
To keep the behavior, I added ccflags-remove-y to all Makefiles
in subdirectories of lib/, except the following:
lib/vdso/Makefile - Kbuild does not descend into this Makefile
lib/raid/test/Makefile - This is not used for the kernel build
I think commit 2464a609de ("ftrace: do not trace library functions")
excluded too much. In the next commit, I will remove ccflags-remove-y
from the sub-directories of lib/.
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Brendan Higgins <brendanhiggins@google.com> (KUnit)
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Pull media updates from Mauro Carvalho Chehab:
- Legacy soc_camera driver was removed from staging
- New I2C sensor related drivers: dw9768, ch7322, max9271, rdacm20
- TI vpe driver code was re-organized and had new features added
- Added Xilinx MIPI CSI-2 Rx Subsystem driver
- Added support for Infrared Toy and IR Droid devices
- Lots of random driver fixes, new features and cleanups
* tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (318 commits)
media: camss: fix memory leaks on error handling paths in probe
media: davinci: vpif_capture: fix potential double free
media: radio: remove redundant assignment to variable retval
media: allegro: fix potential null dereference on header
media: mtk-mdp: Fix a refcounting bug on error in init
media: allegro: fix an error pointer vs NULL check
media: meye: fix missing pm_mchip_mode field
media: cafe-driver: use generic power management
media: saa7164: use generic power management
media: v4l2-dev/ioctl: Fix document for VIDIOC_QUERYCAP
media: v4l2: Correct kernel-doc inconsistency
media: v4l2: Correct kernel-doc inconsistency
media: dvbdev.h: keep * together with the type
media: v4l2-subdev.h: keep * together with the type
media: videobuf2: Print videobuf2 buffer state by name
media: colorspaces-details.rst: fix V4L2_COLORSPACE_JPEG description
media: tw68: use generic power management
media: meye: use generic power management
media: cx88: use generic power management
media: cx25821: use generic power management
...
Merge misc updates from Andrew Morton:
- a few MM hotfixes
- kthread, tools, scripts, ntfs and ocfs2
- some of MM
Subsystems affected by this patch series: kthread, tools, scripts, ntfs,
ocfs2 and mm (hofixes, pagealloc, slab-generic, slab, slub, kcsan,
debug, pagecache, gup, swap, shmem, memcg, pagemap, mremap, mincore,
sparsemem, vmalloc, kasan, pagealloc, hugetlb and vmscan).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
mm: vmscan: consistent update to pgrefill
mm/vmscan.c: fix typo
khugepaged: khugepaged_test_exit() check mmget_still_valid()
khugepaged: retract_page_tables() remember to test exit
khugepaged: collapse_pte_mapped_thp() protect the pmd lock
khugepaged: collapse_pte_mapped_thp() flush the right range
mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible
mm: thp: replace HTTP links with HTTPS ones
mm/page_alloc: fix memalloc_nocma_{save/restore} APIs
mm/page_alloc.c: skip setting nodemask when we are in interrupt
mm/page_alloc: fallbacks at most has 3 elements
mm/page_alloc: silence a KASAN false positive
mm/page_alloc.c: remove unnecessary end_bitidx for [set|get]_pfnblock_flags_mask()
mm/page_alloc.c: simplify pageblock bitmap access
mm/page_alloc.c: extract the common part in pfn_to_bitidx()
mm/page_alloc.c: replace the definition of NR_MIGRATETYPE_BITS with PB_migratetype_bits
mm/shuffle: remove dynamic reconfiguration
mm/memory_hotplug: document why shuffle_zone() is relevant
mm/page_alloc: remove nr_free_pagecache_pages()
mm: remove vm_total_pages
...
After removal of CONFIG_HAVE_MEMBLOCK_NODE_MAP we have two equivalent
functions that call memory_present() for each region in memblock.memory:
sparse_memory_present_with_active_regions() and membocks_present().
Moreover, all architectures have a call to either of these functions
preceding the call to sparse_init() and in the most cases they are called
one after the other.
Mark the regions from memblock.memory as present during sparce_init() by
making sparse_init() call memblocks_present(), make memblocks_present()
and memory_present() functions static and remove redundant
sparse_memory_present_with_active_regions() function.
Also remove no longer required HAVE_MEMORY_PRESENT configuration option.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20200712083130.22919-1-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
