Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes: e3978673f5 ("drivers: net: xgene: Fix MSS programming")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The array for initializing the cle is set up on the stack with
almost entirely constant data and then passed to a function that
converts it into HW specific bit patterns. With the latest
addition, the size of this array has grown to the point that
we get a warning about potential stack overflow in allmodconfig
builds:
xgene_enet_cle.c: In function ‘xgene_enet_cle_init’:
xgene_enet_cle.c:836:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Looking a bit deeper at the usage, I noticed that the only modification
of the data is in dead code, as we don't even use the cle module
for phy_mode other than PHY_INTERFACE_MODE_XGMII. This means we
can simply mark the structure constant and access it directly rather
than passing the pointer down through another structure, making
the code more efficient at the same time as avoiding the
warning.
Fixes: a809701fed ("drivers: net: xgene: fix: RSS for non-TCP/UDP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit ARM with 64-bit dma_addr_t I get this warning about an
incorrect format string:
In file included from /git/arm-soc/drivers/net/ethernet/mellanox/mlx5/core/alloc.c:42:0:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c: In function ‘mlx5_frag_buf_alloc_node’:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c:134:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
We have the special %pad format for printing dma_addr_t, so use that
to print the correct address and avoid the warning.
Fixes: 1c1b522808 ("net/mlx5e: Implement Fragmented Work Queue (WQ)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-08
this is a pull request for one patch.
Jiho Chu found and fixed a use-after-free error in the cleanup path in
the peak pcan USB CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-08
I didn't miss your "net-next is closed" email, but it did come as a bit
of a surprise, and due to time-zone differences I didn't have a chance
to react to it until now. We would have had a couple of patches in
bluetooth-next that we'd still have wanted to get to 4.10.
Out of these the most critical one is the H7/CT2 patch for Bluetooth
Security Manager Protocol, something that couldn't be published before
the Bluetooth 5.0 specification went public (yesterday). If these really
can't go to net-next we'll likely be sending at least this patch through
bluetooth.git to net.git for rc1 inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9.
The issue commit 64c3b252e9 ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
