[ Upstream commit 74c97ea3b61e4ce149444f904ee8d4fc7073505b ]
A link time bug that I had fixed before has come back now that
another sub-module was added to the enetc driver:
ERROR: modpost: "enetc_ierb_register_pf" [drivers/net/ethernet/freescale/enetc/fsl-enetc.ko] undefined!
The problem is that the enetc Makefile is not actually used for
the ierb module if that is the only built-in driver in there
and everything else is a loadable module.
Fix it by always entering the directory this time, regardless
of which symbols are configured. This should reliably fix the
problem and prevent it from coming back another time.
Fixes: 112463ddbe ("net: dsa: felix: fix link error")
Fixes: e7d48e5fbf30 ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bff5b62585123823842833ab20b1c0a7fa437f8c ]
Handle return error code of eth_mac_addr();
Fixes: 3d23a05c75 ("gianfar: Enable changing mac addr when if up")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2395dfff5bb40228a187f21f577cd90673d344 ]
On LS1028A, the MAC RX FIFO defaults to the value 2, which is too high
and may lead to RX lock-up under traffic at a rate higher than 6 Gbps.
Set it to 1 instead, as recommended by the hardware design team and by
later versions of the ENETC block guide.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8861bab48b6c1fc3cdbcab8ff9d1eaea43afe7f ]
When using jumbo packets and overrunning rx queue with napi enabled,
the following sequence is observed in gfar_add_rx_frag:
| lstatus | | skb |
t | lstatus, size, flags | first | len, data_len, *ptr |
---+--------------------------------------+-------+-----------------------+
13 | 18002348, 9032, INTERRUPT LAST | 0 | 9600, 8000, f554c12e |
12 | 10000640, 1600, INTERRUPT | 0 | 8000, 6400, f554c12e |
11 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, f554c12e |
10 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, f554c12e |
09 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, f554c12e |
08 | 14000640, 1600, INTERRUPT FIRST | 0 | 1600, 0, f554c12e |
07 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, f554c12e |
06 | 1c000080, 128, INTERRUPT LAST FIRST | 1 | 0, 0, abf3bd6e |
05 | 18002348, 9032, INTERRUPT LAST | 0 | 8000, 6400, c5a57780 |
04 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, c5a57780 |
03 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, c5a57780 |
02 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, c5a57780 |
01 | 10000640, 1600, INTERRUPT | 0 | 1600, 0, c5a57780 |
00 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, c5a57780 |
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This then crashes:
kernel BUG at include/linux/skbuff.h:2277!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c04689f4] skb_pull+0x2c/0x48
LR [c03f62ac] gfar_clean_rx_ring+0x2e4/0x844
Call Trace:
[ec4bfd38] [c06a84c4] _raw_spin_unlock_irqrestore+0x60/0x7c (unreliable)
[ec4bfda8] [c03f6a44] gfar_poll_rx_sq+0x48/0xe4
[ec4bfdc8] [c048d504] __napi_poll+0x54/0x26c
[ec4bfdf8] [c048d908] net_rx_action+0x138/0x2c0
[ec4bfe68] [c06a8f34] __do_softirq+0x3a4/0x4fc
[ec4bfed8] [c0040150] run_ksoftirqd+0x58/0x70
[ec4bfee8] [c0066ecc] smpboot_thread_fn+0x184/0x1cc
[ec4bff08] [c0062718] kthread+0x140/0x144
[ec4bff38] [c0012350] ret_from_kernel_thread+0x14/0x1c
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4d7234ae9a3bb31181f348ade9bbdb55aeb5c5 ]
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3222b5b613db558e9a494bbf53f3c984d90f71ea ]
Michael reports that since linux-next-20210211, the AER messages for ECC
errors have started reappearing, and this time they can be reliably
reproduced with the first ping on one of his LS1028A boards.
$ ping 1[ 33.258069] pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
72.16.0.1
PING [ 33.267050] pcieport 0000:00:1f.0: AER: can't find device of ID0000
172.16.0.1 (172.16.0.1): 56 data bytes
64 bytes from 172.16.0.1: seq=0 ttl=64 time=17.124 ms
64 bytes from 172.16.0.1: seq=1 ttl=64 time=0.273 ms
$ devmem 0x1f8010e10 32
0xC0000006
It isn't clear why this is necessary, but it seems that for the errors
to go away, we must clear the entire RFS and RSS memory, not just for
the ports in use.
Sadly the code is structured in such a way that we can't have unified
logic for the used and unused ports. For the minimal initialization of
an unused port, we need just to enable and ioremap the PF memory space,
and a control buffer descriptor ring. Unused ports must then free the
CBDR because the driver will exit, but used ports can not pick up from
where that code path left, since the CBDR API does not reinitialize a
ring when setting it up, so its producer and consumer indices are out of
sync between the software and hardware state. So a separate
enetc_init_unused_port function was created, and it gets called right
after the PF memory space is enabled.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Reported-by: Michael Walle <michael@walle.cc>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4560b2a3ecdd5d587c4c6eea4339899f173a559a ]
When CONFIG_OF is disabled, there is a harmless warning about
an unused variable:
enetc_pf.c: In function 'enetc_phylink_create':
enetc_pf.c:981:17: error: unused variable 'dev' [-Werror=unused-variable]
Slightly rearrange the code to pass around the of_node as a
function argument, which avoids the problem without hurting
readability.
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201204120800.17193-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 29d98f54a4fe1b6a9089bec8715a1b89ff9ad59c upstream.
The txtime is passed to the driver in skb->skb_mstamp_ns, which is
actually in a union with skb->tstamp (the place where software
timestamps are kept).
Since commit b50a5c70ff ("net: allow simultaneous SW and HW transmit
timestamping"), __sock_recv_timestamp has some logic for making sure
that the two calls to skb_tstamp_tx:
skb_tx_timestamp(skb) # Software timestamp in the driver
-> skb_tstamp_tx(skb, NULL)
and
skb_tstamp_tx(skb, &shhwtstamps) # Hardware timestamp in the driver
will both do the right thing and in a race-free manner, meaning that
skb_tx_timestamp will deliver a cmsg with the software timestamp only,
and skb_tstamp_tx with a non-NULL hwtstamps argument will deliver a cmsg
with the hardware timestamp only.
Why are races even possible? Well, because although the software timestamp
skb->tstamp is private per skb, the hardware timestamp skb_hwtstamps(skb)
lives in skb_shinfo(skb), an area which is shared between skbs and their
clones. And skb_tstamp_tx works by cloning the packets when timestamping
them, therefore attempting to perform hardware timestamping on an skb's
clone will also change the hardware timestamp of the original skb. And
the original skb might have been yet again cloned for software
timestamping, at an earlier stage.
So the logic in __sock_recv_timestamp can't be as simple as saying
"does this skb have a hardware timestamp? if yes I'll send the hardware
timestamp to the socket, otherwise I'll send the software timestamp",
precisely because the hardware timestamp is shared.
Instead, it's quite the other way around: __sock_recv_timestamp says
"does this skb have a software timestamp? if yes, I'll send the software
timestamp, otherwise the hardware one". This works because the software
timestamp is not shared with clones.
But that means we have a problem when we attempt hardware timestamping
with skbs that don't have the skb->tstamp == 0. __sock_recv_timestamp
will say "oh, yeah, this must be some sort of odd clone" and will not
deliver the hardware timestamp to the socket. And this is exactly what
is happening when we have txtime enabled on the socket: as mentioned,
that is put in a union with skb->tstamp, so it is quite easy to mistake
it.
Do what other drivers do (intel igb/igc) and write zero to skb->tstamp
before taking the hardware timestamp. It's of no use to us now (we're
already on the TX confirmation path).
Fixes: 0d08c9ec7d ("enetc: add support time specific departure base on the qos etf")
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5d12c9be6f30080600c8bacaf310194e37d029 upstream.
The RX rings have a producer index owned by hardware, where newly
received frame buffers are placed, and a consumer index owned by
software, where newly allocated buffers are placed, in expectation of
hardware being able to place frame data in them.
Hardware increments the producer index when a frame is received, however
it is not allowed to increment the producer index to match the consumer
index (RBCIR) since the ring can hold at most RBLENR[LENGTH]-1 received
BDs. Whenever the producer index matches the value of the consumer
index, the ring has no unprocessed received frames and all BDs in the
ring have been initialized/prepared by software, i.e. hardware owns all
BDs in the ring.
The code uses the next_to_clean variable to keep track of the producer
index, and the next_to_use variable to keep track of the consumer index.
The RX rings are seeded from enetc_refill_rx_ring, which is called from
two places:
1. initially the ring is seeded until full with enetc_bd_unused(rx_ring),
i.e. with 511 buffers. This will make next_to_clean=0 and next_to_use=511:
.ndo_open
-> enetc_open
-> enetc_setup_bdrs
-> enetc_setup_rxbdr
-> enetc_refill_rx_ring
2. then during the data path processing, it is refilled with 16 buffers
at a time:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_clean_rx_ring
-> enetc_refill_rx_ring
There is just one problem: the initial seeding done during .ndo_open
updates just the producer index (ENETC_RBPIR) with 0, and the software
next_to_clean and next_to_use variables. Notably, it will not update the
consumer index to make the hardware aware of the newly added buffers.
Wait, what? So how does it work?
Well, the reset values of the producer index and of the consumer index
of a ring are both zero. As per the description in the second paragraph,
it means that the ring is full of buffers waiting for hardware to put
frames in them, which by coincidence is almost true, because we have in
fact seeded 511 buffers into the ring.
But will the hardware attempt to access the 512th entry of the ring,
which has an invalid BD in it? Well, no, because in order to do that, it
would have to first populate the first 511 entries, and the NAPI
enetc_poll will kick in by then. Eventually, after 16 processed slots
have become available in the RX ring, enetc_clean_rx_ring will call
enetc_refill_rx_ring and then will [ finally ] update the consumer index
with the new software next_to_use variable. From now on, the
next_to_clean and next_to_use variables are in sync with the producer
and consumer ring indices.
So the day is saved, right? Well, not quite. Freeing the memory
allocated for the rings is done in:
enetc_close
-> enetc_clear_bdrs
-> enetc_clear_rxbdr
-> this just disables the ring
-> enetc_free_rxtx_rings
-> enetc_free_rx_ring
-> sets next_to_clean and next_to_use to 0
but again, nothing is committed to the hardware producer and consumer
indices (yay!). The assumption is that the ring is disabled, so the
indices don't matter anyway, and it's the responsibility of the "open"
code path to set those up.
.. Except that the "open" code path does not set those up properly.
While initially, things almost work, during subsequent enetc_close ->
enetc_open sequences, we have problems. To be precise, the enetc_open
that is subsequent to enetc_close will again refill the ring with 511
entries, but it will leave the consumer index untouched. Untouched
means, of course, equal to the value it had before disabling the ring
and draining the old buffers in enetc_close.
But as mentioned, enetc_setup_rxbdr will at least update the producer
index though, through this line of code:
enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);
so at this stage we'll have:
next_to_clean=0 (in hardware 0)
next_to_use=511 (in hardware we'll have the refill index prior to enetc_close)
Again, the next_to_clean and producer index are in sync and set to
correct values, so the driver manages to limp on. Eventually, 16 ring
entries will be consumed by enetc_poll, and the savior
enetc_clean_rx_ring will come and call enetc_refill_rx_ring, and then
update the hardware consumer ring based upon the new next_to_use.
So.. it works?
Well, by coincidence, it almost does, but there's a circumstance where
enetc_clean_rx_ring won't be there to save us. If the previous value of
the consumer index was 15, there's a problem, because the NAPI poll
sequence will only issue a refill when 16 or more buffers have been
consumed.
It's easiest to illustrate this with an example:
ip link set eno0 up
ip addr add 192.168.100.1/24 dev eno0
ping 192.168.100.1 -c 20 # ping this port from another board
ip link set eno0 down
ip link set eno0 up
ping 192.168.100.1 -c 20 # ping it again from the same other board
One by one:
1. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 0)
2. ping 192.168.100.1 -c 20 # ping this port from another board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=15 next_to_clean 14 (in hw 15) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: enetc_refill_rx_ring(16) increments next_to_use by 16 (mod 512) and writes it to hw
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=0 next_to_clean 15 (in hw 16) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 16 (in hw 17) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 17 (in hw 18) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 18 (in hw 19) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 19 (in hw 20) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 20 (in hw 21) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 21 (in hw 22) next_to_use 15 (in hw 15)
20 packets transmitted, 20 packets received, 0% packet loss
3. ip link set eno0 down
enetc_free_rx_ring: next_to_clean 0 (in hw 22), next_to_use 0 (in hw 15)
4. ip link set eno0 up
-> calls enetc_setup_rxbdr:
-> calls enetc_refill_rx_ring(511 buffers)
-> next_to_clean=0 (in hw 0)
-> next_to_use=511 (in hw 15)
5. ping 192.168.100.1 -c 20 # ping it again from the same other board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 15)
20 packets transmitted, 12 packets received, 40% packet loss
And there it dies. No enetc_refill_rx_ring (because cleaned_cnt must be equal
to 15 for that to happen), no nothing. The hardware enters the condition where
the producer (14) + 1 is equal to the consumer (15) index, which makes it
believe it has no more free buffers to put packets in, so it starts discarding
them:
ip netns exec ns0 ethtool -S eno0 | grep -v ': 0'
NIC statistics:
Rx ring 0 discarded frames: 8
Summarized, if the interface receives between 16 and 32 (mod 512) frames
and then there is a link flap, then the port will eventually die with no
way to recover. If it receives less than 16 (mod 512) frames, then the
initial NAPI poll [ before the link flap ] will not update the consumer
index in hardware (it will remain zero) which will be ok when the buffers
are later reinitialized. If more than 32 (mod 512) frames are received,
the initial NAPI poll has the chance to refill the ring twice, updating
the consumer index to at least 32. So after the link flap, the consumer
index is still wrong, but the post-flap NAPI poll gets a chance to
refill the ring once (because it passes through cleaned_cnt=15) and
makes the consumer index be again back in sync with next_to_use.
The solution to this problem is actually simple, we just need to write
next_to_use into the hardware consumer index at enetc_open time, which
always brings it back in sync after an initial buffer seeding process.
The simpler thing would be to put the write to the consumer index into
enetc_refill_rx_ring directly, but there are issues with the MDIO
locking: in the NAPI poll code we have the enetc_lock_mdio() taken from
top-level and we use the unlocked enetc_wr_reg_hot, whereas in
enetc_open, the enetc_lock_mdio() is not taken at the top level, but
instead by each individual enetc_wr_reg, so we are forced to put an
additional enetc_wr_reg in enetc_setup_rxbdr. Better organization of
the code is left as a refactoring exercise.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96a5223b918c8b79270fc0fec235a7ebad459098 upstream.
The Station Interface Receive Interrupt Detect Register (SIRXIDR)
contains a 16-bit wide mask of 'interrupt detected' events for each ring
associated with a port. Bit i is write-1-to-clean for RX ring i.
I have no explanation whatsoever how this line of code came to be
inserted in the blamed commit. I checked the downstream versions of that
patch and none of them have it.
The somewhat comical aspect of it is that we're writing a binary number
to the SIRXIDR register, which is derived from enetc_bd_unused(rx_ring).
Since the RX rings have 512 buffer descriptors, we end up writing 511 to
this register, which is 0x1ff, so we are effectively clearing the
'interrupt detected' event for rings 0-8.
This register is not what is used for interrupt handling though - it
only provides a summary for the entire SI. The hardware provides one
separate Interrupt Detect Register per RX ring, which auto-clears upon
read. So there doesn't seem to be any adverse effect caused by this
bogus write.
There is, however, one reason why this should be handled as a bugfix:
next_to_clean _should_ be committed to hardware, just not to that
register, and this was obscuring the fact that it wasn't. This is fixed
in the next patch, and removing the bogus line now allows the fix patch
to be backported beyond that point.
Fixes: fd5736bf9f ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c76a97218dcbb2cb7cec1404ace43ef96c87d874 upstream.
The ENETC port 0 MAC supports in-band status signaling coming from a PHY
when operating in RGMII mode, and this feature is enabled by default.
It has been reported that RGMII is broken in fixed-link, and that is not
surprising considering the fact that no PHY is attached to the MAC in
that case, but a switch.
This brings us to the topic of the patch: the enetc driver should have
not enabled the optional in-band status signaling for RGMII unconditionally,
but should have forced the speed and duplex to what was resolved by
phylink.
Note that phylink does not accept the RGMII modes as valid for in-band
signaling, and these operate a bit differently than 1000base-x and SGMII
(notably there is no clause 37 state machine so no ACK required from the
MAC, instead the PHY sends extra code words on RXD[3:0] whenever it is
not transmitting something else, so it should be safe to leave a PHY
with this option unconditionally enabled even if we ignore it). The spec
talks about this here:
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/RGMIIv1_5F00_3.pdf
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a74dbce9d4541888fe0d39afe69a3a95004669b4 upstream.
Quoting from the blamed commit:
In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Intuitive or not, there isn't any definition issued by a standards body
which says that promiscuity has anything to do with VLAN filtering - it
only has to do with accepting packets regardless of destination MAC address.
In fact people are already trying to use this misunderstanding/bug of
the enetc driver as a justification to transform promiscuity into
something it never was about: accepting every packet (maybe that would
be the "rx-all" netdev feature?):
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/
This is relevant because there are use cases in the kernel (such as
tc-flower rules with the protocol 802.1Q and a vlan_id key) which do not
(yet) use the vlan_vid_add API to be compatible with VLAN-filtering NICs
such as enetc, so for those, disabling rx-vlan-filter is currently the
only right solution to make these setups work:
https://lore.kernel.org/netdev/CA+h21hoxwRdhq4y+w8Kwgm74d4cA0xLeiHTrmT-VpSaM7obhkg@mail.gmail.com/
The blamed patch has unintentionally introduced one more way for this to
work, which is to enable IFF_PROMISC, however this is non-portable
because port promiscuity is not meant to disable VLAN filtering.
Therefore, it could invite people to write broken scripts for enetc, and
then wonder why they are broken when migrating to other drivers that
don't handle promiscuity in the same way.
Fixes: 7070eea5e9 ("enetc: permit configuration of rx-vlan-filter with ethtool")
Cc: Markus Blöchl <Markus.Bloechl@ipetronik.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 827b6fd046516af605e190c872949f22208b5d41 upstream.
When the enetc ports have rx-vlan-offload enabled, they report a TPID of
ETH_P_8021Q regardless of what was actually in the packet. When
rx-vlan-offload is disabled, packets have the proper TPID. Fix this
inconsistency by finishing the TODO left in the code.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d36ecdbc4410e61a0e02adc5d3abeee22a8ffd3 upstream.
The workaround for the ENETC MDIO erratum caused a performance
degradation of 82 Kpps (seen with IP forwarding of two 1Gbps streams of
64B packets). This is due to excessive locking and unlocking in the fast
path, which can be avoided.
By taking the MDIO read-side lock only once per NAPI poll cycle, we are
able to regain 54 Kpps (65%) of the performance hit. The rest of the
performance degradation comes from the TX data path, but unfortunately
it doesn't look like we can optimize that away easily, even with
netdev_xmit_more(), there just isn't any skb batching done, to help with
taking the MDIO lock less often than once per packet.
We need to change the register accessor type for enetc_get_tx_tstamp,
because it now runs under the enetc_lock_mdio as per the new call path
detailed below:
enetc_msix
-> napi_schedule
-> enetc_poll
-> enetc_lock_mdio
-> enetc_clean_tx_ring
-> enetc_get_tx_tstamp
-> enetc_clean_rx_ring
-> enetc_unlock_mdio
Fixes: fd5736bf9f ("enetc: Workaround for MDIO register access issue")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c646d10dda2dcde82c6ce5a474522621ab2b8b19 upstream.
After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:
enetc_pf_probe
-> enetc_alloc_si_resources
-> enetc_configure_si
-> enetc_setup_default_rss_table
is overwritten later in:
enetc_pf_probe
-> enetc_init_port_rss_memory
which zero-initializes the entire port RSS table in order to avoid ECC errors.
The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.
The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3af409ca278d4a8d50e91f9f7c4c33b175645cf3 ]
The following call path suggests that calling unregister_netdev on an
interface that is up will first bring it down.
enetc_pf_remove
-> unregister_netdev
-> unregister_netdevice_queue
-> unregister_netdevice_many
-> dev_close_many
-> __dev_close_many
-> enetc_close
-> enetc_stop
-> phylink_stop
However, enetc first destroys the phylink instance, then calls
unregister_netdev. This is already dissimilar to the setup (and error
path teardown path) from enetc_pf_probe, but more than that, it is buggy
because it is invalid to call phylink_stop after phylink_destroy.
So let's first unregister the netdev (and let the .ndo_stop events
consume themselves), then destroy the phylink instance, then free the
netdev.
Fixes: 71b77a7a27 ("enetc: Migrate to PHYLINK and PCS_LYNX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e12be9139cca26d689fe1a9257054b76752f725b ]
If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07bf34a50e327975b21a9dee64d220c3dcb72ee9 ]
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 445c6198fe7be03b7d38e66fe8d4b3187bc251d4 ]
Since commit 1d6cd3929360 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 887078de2a23689e29d6fa1b75d7cbc544c280be ]
Table 8-53 in the QUICC Engine Reference manual shows definitions of
fields up to a size of 192 bytes, not just 128. But in table 8-111,
one does find the text
Base Address of the Global Transmitter Parameter RAM Page. [...]
The user needs to allocate 128 bytes for this page. The address must
be aligned to the page size.
I've checked both rev. 7 (11/2015) and rev. 9 (05/2018) of the manual;
they both have this inconsistency (and the table numbers are the
same).
Adding a bit of debug printing, on my board the struct
ucc_geth_tx_global_pram is allocated at offset 0x880, while
the (opaque) ucc_geth_thread_data_tx gets allocated immediately
afterwards, at 0x900. So whatever the engine writes into the thread
data overlaps with the tail of the global tx pram (and devmem says
that something does get written during a simple ping).
I haven't observed any failure that could be attributed to this, but
it seems to be the kind of thing that would be extremely hard to
debug. So extend the struct definition so that we do allocate 192
bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1385ae5c30f238f81bc6528d897c6d7a0816783f ]
All the buffers and registers are already set up appropriately for an
MTU slightly above 1500, so we just need to expose this to the
networking stack. AFAICT, there's no need to implement .ndo_change_mtu
when the receive buffers are always set up to support the max_mtu.
This fixes several warnings during boot on our mpc8309-board with an
embedded mv88e6250 switch:
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 0
...
mv88e6085 mdio@e0102120:10: nonfatal error -34 setting MTU 1500 on port 4
ucc_geth e0102000.ethernet eth1: error -22 setting MTU to 1504 to include DSA overhead
The last line explains what the DSA stack tries to do: achieving an MTU
of 1500 on-the-wire requires that the master netdevice connected to
the CPU port supports an MTU of 1500+the tagging overhead.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e925e0cd2a705aaacb0b907bb3691fcac3a973a4 ]
ugeth is the netdiv_priv() part of the netdevice. Accessing the memory
pointed to by ugeth (such as done by ucc_geth_memclean() and the two
of_node_puts) after free_netdev() is thus use-after-free.
Fixes: 80a9fad8e8 ("ucc_geth: fix module removal")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54a57d1c449275ee727154ac106ec1accae012e3 ]
This patch fixes an error condition triggered when the code path which
transmits a S/G frame descriptor when the skb's headroom is not enough
for DPAA2's needs.
We are greated with a splat like the one below when a SGT structure is
recycled and that is because even though a dma_unmap is performed on the
Tx confirmation path, the unmap is not done with the proper size.
[ 714.464927] WARNING: CPU: 13 PID: 0 at drivers/iommu/io-pgtable-arm.c:281 __arm_lpae_map+0x2d4/0x30c
(...)
[ 714.465343] Call trace:
[ 714.465348] __arm_lpae_map+0x2d4/0x30c
[ 714.465353] __arm_lpae_map+0x114/0x30c
[ 714.465357] __arm_lpae_map+0x114/0x30c
[ 714.465362] __arm_lpae_map+0x114/0x30c
[ 714.465366] arm_lpae_map+0xf4/0x180
[ 714.465373] arm_smmu_map+0x4c/0xc0
[ 714.465379] __iommu_map+0x100/0x2bc
[ 714.465385] iommu_map_atomic+0x20/0x30
[ 714.465391] __iommu_dma_map+0xb0/0x110
[ 714.465397] iommu_dma_map_page+0xb8/0x120
[ 714.465404] dma_map_page_attrs+0x1a8/0x210
[ 714.465413] __dpaa2_eth_tx+0x384/0xbd0 [fsl_dpaa2_eth]
[ 714.465421] dpaa2_eth_tx+0x84/0x134 [fsl_dpaa2_eth]
[ 714.465427] dev_hard_start_xmit+0x10c/0x2b0
[ 714.465433] sch_direct_xmit+0x1a0/0x550
(...)
The dpaa2-eth driver uses an area of software annotations to transmit
necessary information from the Tx path to the Tx confirmation one. This
SWA structure has a different layout for each kind of frame that we are
dealing with: linear, S/G or XDP.
The commit referenced was incorrectly setting up the 'sgt_size' field
for the S/G type of SWA even though we are dealing with a linear skb
here.
Fixes: d70446ee1f ("dpaa2-eth: send a scatter-gather FD instead of realloc-ing")
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201211171607.108034-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'
Fixes: ceeb03ad8e ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to a hardware issue, an access to MDIO registers
that is concurrent with other ENETC register accesses
may lead to the MDIO access being dropped or corrupted.
The workaround introduces locking for all register accesses
to the ENETC register space. To reduce performance impact,
a readers-writers locking scheme has been implemented.
The writer in this case is the MDIO access code (irrelevant
whether that MDIO access is a register read or write), and
the reader is any access code to non-MDIO ENETC registers.
Also, the datapath functions acquire the read lock fewer times
and use _hot accessors. All the rest of the code uses the _wa
accessors which lock every register access.
The commit introducing MDIO support is -
commit ebfcb23d62 ("enetc: Add ENETC PF level external MDIO support")
but due to subsequent refactoring this patch is applicable on
top of a later commit.
Fixes: 6517798dd3 ("enetc: Make MDIO accessors more generic and export to include/linux/fsl")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201112182608.26177-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc3, including fixes from wireless, can, and
netfilter subtrees.
Current merge window - bugs in new features:
- can: isotp: isotp_rcv_cf(): enable RX timeout handling in
listen-only mode
Previous releases - regressions:
- mac80211:
- don't require VHT elements for HE on 2.4 GHz
- fix regression where EAPOL frames were sent in plaintext
- netfilter:
- ipset: Update byte and packet counters regardless of whether
they match
- ip_tunnel: fix over-mtu packet send by allowing fragmenting even if
inner packet has IP_DF (don't fragment) set in its header (when
TUNNEL_DONT_FRAGMENT flag is not set on the tunnel dev)
- net: fec: fix MDIO probing for some FEC hardware blocks
- ip6_tunnel: set inner ipproto before ip6_tnl_encap to un-break gso
support
- sctp: Fix COMM_LOST/CANT_STR_ASSOC err reporting on big-endian
platforms, sparse-related fix used the wrong integer size
Previous releases - always broken:
- netfilter: use actual socket sk rather than skb sk when routing
harder
- r8169: work around short packet hw bug on RTL8125 by padding frames
- net: ethernet: ti: cpsw: disable PTPv1 hw timestamping
advertisement, the hardware does not support it
- chelsio/chtls: fix always leaking ctrl_skb and another leak caused
by a race condition
- fix drivers incorrectly writing into skbs on TX:
- cadence: force nonlinear buffers to be cloned
- gianfar: Account for Tx PTP timestamp in the skb headroom
- gianfar: Replace skb_realloc_headroom with skb_cow_head for PTP
- can: flexcan:
- remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
- add ECC initialization for VF610 and LX2160A
- flexcan_remove(): disable wakeup completely
- can: fix packet echo functionality:
- peak_canfd: fix echo management when loopback is on
- make sure skbs are not freed in IRQ context in case they need to
be dropped
- always clone the skbs to make sure they have a reference on the
socket, and prevent it from disappearing
- fix real payload length return value for RTR frames
- can: j1939: return failure on bind if netdev is down, rather than
waiting indefinitely
Misc:
- IPv6: reply ICMP error if the first fragment don't include all
headers to improve compliance with RFC 8200"
* tag 'net-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
ionic: check port ptr before use
r8169: work around short packet hw bug on RTL8125
net: openvswitch: silence suspicious RCU usage warning
chelsio/chtls: fix always leaking ctrl_skb
chelsio/chtls: fix memory leaks caused by a race
can: flexcan: flexcan_remove(): disable wakeup completely
can: flexcan: add ECC initialization for VF610
can: flexcan: add ECC initialization for LX2160A
can: flexcan: remove FLEXCAN_QUIRK_DISABLE_MECR quirk for LS1021A
can: mcp251xfd: remove unneeded break
can: mcp251xfd: mcp251xfd_regmap_nocrc_read(): fix semicolon.cocci warnings
can: mcp251xfd: mcp251xfd_regmap_crc_read(): increase severity of CRC read error messages
can: peak_canfd: pucan_handle_can_rx(): fix echo management when loopback is on
can: peak_usb: peak_usb_get_ts_time(): fix timestamp wrapping
can: peak_usb: add range checking in decode operations
can: xilinx_can: handle failure cases of pm_runtime_get_sync
can: ti_hecc: ti_hecc_probe(): add missed clk_disable_unprepare() in error path
can: isotp: padlen(): make const array static, makes object smaller
can: isotp: isotp_rcv_cf(): enable RX timeout handling in listen-only mode
can: isotp: Explain PDU in CAN_ISOTP help text
...
The headroom reserved for received frames needs to be aligned to an
RX specific value. There is currently a discrepancy between the values
used in the Ethernet driver and the values passed to the FMan.
Coincidentally, the resulting aligned values are identical.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Impose a larger RX private data area only when the A050385 erratum is
present on the hardware. A smaller buffer size is sufficient in all
other scenarios. This enables a wider range of linear Jumbo frame
sizes in non-erratum scenarios, instead of turning to multi
buffer Scatter/Gather frames. The maximum linear frame size is
increased by 128 bytes for non-erratum arm64 platforms.
Cleanup the hardware annotations header defines in the process.
Fixes: 3c68b8fffb ("dpaa_eth: FMan erratum A050385 workaround")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull more flexible-array member conversions from Gustavo A. R. Silva:
"Replace zero-length arrays with flexible-array members"
* tag 'flexible-array-conversions-5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
printk: ringbuffer: Replace zero-length array with flexible-array member
net/smc: Replace zero-length array with flexible-array member
net/mlx5: Replace zero-length array with flexible-array member
mei: hw: Replace zero-length array with flexible-array member
gve: Replace zero-length array with flexible-array member
Bluetooth: btintel: Replace zero-length array with flexible-array member
scsi: target: tcmu: Replace zero-length array with flexible-array member
ima: Replace zero-length array with flexible-array member
enetc: Replace zero-length array with flexible-array member
fs: Replace zero-length array with flexible-array member
Bluetooth: Replace zero-length array with flexible-array member
params: Replace zero-length array with flexible-array member
tracepoint: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_proto: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_commands: Replace zero-length array with flexible-array member
mailbox: zynqmp-ipi-message: Replace zero-length array with flexible-array member
dmaengine: ti-cppi5: Replace zero-length array with flexible-array member
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on the second option,
using skb_realloc_headroom() to create a new skb to accommodate
PTP frames. Turns out that this method is not reliable, as
reallocation of skbs for PTP frames along with the required
overhead (skb_set_owner_w, consume_skb) is causing random
crashes in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time on the same device
(as seen in James' report).
Note that these crashes don't occur with a single TCP stream,
nor with multiple concurrent UDP streams, but only when multiple
TCP streams are run concurrently with the PTP packet flow
(doing skb reallocation).
This patch enforces the first method, by requesting enough
headroom from the stack to accommodate PTP frames, and so avoiding
skb_realloc_headroom() & co, and the crashes no longer occur.
There's no reason not to set needed_headroom to a large enough
value to accommodate PTP frames, so in this regard this patch
is a fix.
Reported-by: James Jurack <james.jurack@ametek.com>
Fixes: bee9e58c9e ("gianfar:don't add FCB length to hard_header_len")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201020173605.1173-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on skb_realloc_headroom()
to create new skbs to accommodate PTP frames. Turns out that
this method is not reliable in this context at least, as
skb_realloc_headroom() for PTP frames can cause random crashes,
mostly in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time with the PTP flow
on the same device (as seen in James' report). I also noticed
that when the system is loaded by sending multiple TCP streams,
the driver receives cloned skbs in large numbers.
skb_cow_head() instead proves to be stable in this scenario,
and not only handles cloned skbs too but it's also more efficient
and widely used in other drivers.
The commit introducing skb_realloc_headroom in the driver
goes back to 2009, commit 93c1285c5d
("gianfar: reallocate skb when headroom is not enough for fcb").
For practical purposes I'm referencing a newer commit (from 2012)
that brings the code to its current structure (and fixes the PTP
case).
Fixes: 9c4886e5e6 ("gianfar: Fix invalid TX frames returned on error queue when time stamping")
Reported-by: James Jurack <james.jurack@ametek.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201029081057.8506-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.
Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.
Fixes: f166f890c8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Clang warns about the extra parentheses in this comparison:
drivers/net/ethernet/freescale/ucc_geth.c:1361:28:
warning: equality comparison with extraneous parentheses
if ((ugeth->phy_interface == PHY_INTERFACE_MODE_SGMII))
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
It seems clear the intent here is to do a comparison not an
assignment, so drop the extra parentheses to avoid any confusion.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20201023033236.3296988-1-mpe@ellerman.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Decouple level MAC configuration based on phy interface type
from general port configuration.
Group together MAC and link configuration code.
Decouple external mdio bus creation from interface type
parsing. No longer return an (unhandled) error code when
phy_node not found, use phy_node to indicate whether the
port has a phy or not. No longer fall-through when serdes
configuration fails for the link modes that require
internal link configuration.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When packets are received on the error queue, this function under
net_ratelimit():
netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");
does not get printed. Instead we only see:
[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed
Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
