This is needed by the USB code. Also while at it replace one void pointer
with a properly typed pointer.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adding below steps helps to get good power numbers
in deep sleep suspend path,
* Disable WOW mode.
* Flush data packets and wait for all control packets.
to be cleared in TX path before deep sleep suspend.
* Set host sleep mode to SLEEP.
Below steps are added to perform the recovery action
while the system resume from deep sleep,
* Set host sleep mode to AWAKE.
* Reset scan parameters to default value.
In addition, Debug prints are added to track deep sleep
suspend/resume state.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The piece of code used in ath6kk_wow_suspend function
to configure the host sleep mode is needed in deep sleep
case also.
Moving that portion to a separate function called
ath6kl_update_host_mode() would be helpful to avoid
the duplication of the same code in deep sleep path.
There is no functional change.
kvalo: move inline functions to cfg80211.c and fix a long line
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Dump htc header along with the warning message when the request
to Rx with invalid frame length is detected.
kvalo: fix open parenthesis alignment
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the device disconnects from an AP when it is in suspending state. You will
get the following message from wpa_supplicant after waking the device up and
sending scan request:
"Scan trigger failed: ret=-16 (Device or resource busy)"
Fix the issue by sending a scan complete event before starting scheduled
scan.
kvalo: cosmetic changes to commit log
Signed-off-by: Isaac.li <shonmou@gmail.com>
Tested-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware reports the below ARP offload related information
while sending the target statistic event to the host.
* Number of ARP packets received.
* Number of packets matched with the device IP addr.
* Number of ARP response packet sent to the remote.
This patch adds the additional debug prints in debugfs
entry tgt_stats. It will be useful to know the ARP offload
execution status.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is useful during debugging to check if disconnect commands were issued by
the host.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 7504a3e1 ("ath6kl: add padding to firmware log records") accidentally
changed debug.c mode from 100644 to 100755. Revert that back to original.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl/cfg80211.c:589: WARNING: max() should probably be
max_t(u16, vif->listen_intvl_t, ATH6KL_MAX_WOW_LISTEN_INTL)
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
My patch 24fc32b3 ("ath6kl: add ath6kl_bmi_write_hi32()") caused a regression
in ath6kl_upload_board_file() and the board_address variable was not
properly initialised in some cases:
ath6kl/init.c:1068:6: warning: ‘board_address’ may be used uninitialized
in this function
Most likely this broke ar6004 support but I can't test that right now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by
memsetting rx_status in ath_rx_tasklet.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On systems with multiple NICs, it's nice to know which
one is producing warnings. Here is an example of the
new ouput:
ath: wiphy0: Failed to stop TX DMA, queues=0x005!
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.
kvalo: more details to the commit log
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
