The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.
Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
The Touch controller and LCD Panel share the same SPI bus 1.
So, we need to define the touch controller in the SPI board info
else, the SPI bus will be contended due to invalid state of
Touch controller's Chip Select thus preventing the LCD panel
from working.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
These files include linux/bootmem.h without using anything from this
file; remove the unnecessary include.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In OMAP4, there is only one irq line for TX and RX paths. Use
the correct irq line to avoid errors at runtime.
Also, request irq line only once (instead of requesting for TX
and RX).
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c
[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.
The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch enables the wakeup capabilities of ads7846 touchscreen driver.
ads7846 driver can now wakeup the system from suspend on OMAP3430 EVM
and SDP boards.
The earlier approach of enabling wakeup on the touchscreen GPIO pin during
board level mux init is removed. Instead the wakeup flag in
ads7846_platform_data is enabled. Based on the flag, the ads7846 driver
will do an enable_irq_wake which will eventually call into the OMAP GPIO
layer and will enable the wakeup capability on the GPIO pin.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3530 TRM section 7.4.4.4.2 requires OFFOUTENABLE to be set (active low)
if wakeup capabilities are enabled on a pad. During OFF mode testing
on OMAP3530 EVM, it was observed that the device was not residing in
the OFF state. The device enters into the OFF state and immediately exits
from that state as if an IO wakeup event has occured. The issue was traced
down to the pad configuration of wkaeup enabled pad's.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are currently non-muxable, so let's save some memory
and remove them. Otherwise we get the following warnings:
mux: Unknown ball offset 0x5e
mux: Unknown ball offset 0x60
mux: Unknown ball offset 0x62
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can get the following error:
error: variable 'tdo24m_mcspi_config' has initializer but incomplete type
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.
Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.
Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.
Cc: Allen Pais <allen.pais@ti.com>
Acked-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the initialisation routines for the OMAP2 and OMAP3
boards so that they register their PMU IRQs with the PMU framework in
the Kernel.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
Old code from original patch contains beagle board pins that are
not available on the Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change position of calling serial and ethernet initialization.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devkit8000 uses the CUS package for OMAP3530.
This patch adds missing package selection for CUS and enables
CONFIG_MUX.
Replace whitespace with tab in Kconfig.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected type of flash in output (OneNAND => NOR).
Removed whitespace after newline in output.
Removed double whitespace in output.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If gpmc_t isn't given, we don't need to set timing for gpmc, or it will cause
a Oops.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The initialize of i2c subsystem will set pinmux, so it should be done
after the initialize of mux subsystem initialization.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the name for the spi instances on omap44xx_clks to match
the names omap2 spi driver gives:
omap-mcspi.1 -> omap2_mcspi.1
omap-mcspi.2 -> omap2_mcspi.2
omap-mcspi.3 -> omap2_mcspi.3
omap-mcspi.4 -> omap2_mcspi.4
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
