The usb is very much like on am33xx, we just put the some of the
componends under scm where they belong.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a 2GB emmc on hp t410 that's wired to the sd_2 interface.
Note that we also need to configure the evtmux using edma_xbar for
edma channels.
Let's use the McASP2 channels like the original kernel seems to be
doing, most likely the audio on t410 is different from dm814x-evm.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The edma is the same as on am33xx, except it has four tptc
instances. And we need the edma_xbar for at least mmc3, so
let's use the edma_xbar and the new binding as suggested by
Peter Ujfalusi <peter.ujfalusi@ti.com>.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for ti,edma-memcpy-channels binding]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's add the DM814X_IOPAD macro the same way as we have for dm816x and
am33xx as this allows comparing the registers with the documentation easily.
The pinctrl bits are yet again different on dm814x.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dra762x j5-eco is similar to dm814x with a bit different clocks
and devices.
[tony@atomide.com: updated to leave out adpll clock driver references]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling CPUFreq support for Tegra124 Chromebooks is causing the Tegra124
to hang when resuming from suspend.
When CPUFreq is enabled, the CPU clock is changed from the PLLX clock to
the DFLL clock during kernel boot. When resuming from suspend the CPU
clock is temporarily changed back to the PLLX clock before switching back
to the DFLL. If the DFLL is operating at a much lower frequency than the
PLLX when we enter suspend, and so the CPU voltage rail is at a voltage
too low for the CPUs to operate at the PLLX frequency, then the device
will hang.
Please note that the PLLX is used in the resume sequence to switch the CPU
clock from the very slow 32K clock to a faster clock during early resume
to speed up the resume sequence before the DFLL is resumed.
Ideally, we should fix this by setting the suspend frequency so that it
matches the PLLX frequency, however, that would be a bigger change. For
now simply disable CPUFreq support for Tegra124 Chromebooks to avoid the
hang when resuming from suspend.
Fixes: 9a0baee960 ("ARM: tegra: Enable CPUFreq support for Tegra124
Chromebooks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT patches, round 2
Mostly some audio codec patches to enable it on more boards, and a bunch
devices activation (Ethernet, touchscreen, backlights). One more board has
been added too.
* tag 'sunxi-dt-for-4.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun5i: Add dts file for the Empire Electronix D709 tablet
ARM: dts: sun7i: Enable gmac on Wits Pro A20 DKT
ARM: dt: sun7i: Enable audio codec on MK808C
ARM: sunxi: dt: enable audio codec on mk802
ARM: dts: sun7i: Add PA gpio pin to Wexler TAB7200 tablet
ARM: dts: sun7i: Add backlight node to Wexler TAB7200 tablet
ARM: dts: sun7i: Enable touchscreen on Wexler TAB7200 tablet
ARM: dts: sun7i: Enable PWM controller on Wexler TAB7200 tablet
ARM: dts: sun4i: gemei-g9: Enable PA GPIO pin configuration
ARM: dts: sun4i: Enable onboard codec used on the pov protab2-ips9 tablet
ARM: dts: sun5i: Enable onboard codec used on the UTOO P66 tablet
Signed-off-by: Olof Johansson <olof@lixom.net>
Second batch of DT changes for 4.5:
- addition of sound nodes for sama5d2 and the xplained
- addition of a new patform by Landis+Gyr: VInCo
* tag 'at91-4.5-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91/dt: sama5d2 Xplained: add pdmic node
ARM: at91/dt: sama5d2: add pdmic node
ARM: at91/dt: Add Support for the L+G VInCo platform
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX device tree updates for 4.5:
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
* tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx7d: sbc-imx7: add basic board support
ARM: dts: imx7d: cl-som-imx7: add basic module support
ARM: dts: TS-4800: add touchscreen support
ARM: dts: ts-4800: Add LCD support
ARM: dts: imx6q: add Novena board
devicetree: bindings: Add vendor prefix for Kosagi
ARM: dts: TS-4800: use weim IP to map the FPGA
ARM: dts: TS-4800: drop uart rts/cts pin reservations
ARM: dts: imx6: add Vivante GPU nodes
ARM: dts: imx28: add alternate auart4 pinmux
ARM: dts: ls1021a: add sata node to dts
ARM: dts: TS-4800: add basic device tree
of: documentation: add bindings documentation for TS-4800
of: add vendor prefix for Technologic Systems
ARM: dts: imx7d-sdb: add ADC support
ARM: dts: imx7d.dtsi: add ADC support
ARM: dts: vf-colibri: add CAN support
ARM: mxs: dt: cfa10057: fix backlight PWM
ARM: dts: imx6qdl: move GIC to right location in DT
ARM: dts: imx6qdl: add IPU aliases
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
ARM: dts: AM4372: add entry for qspi mmap region
ARM: dts: DRA7: add entry for qspi mmap region
ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
ARM: dts: cm-t335: add support for bluetooth
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for USB0
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>
Few fixes for omaps to allow am437x only builds to boot properly with
CPU_IDLE and ARM TWD timer. This is probably a common configuration setup
for people making products with these SoCs so let's make sure it works.
Also a wakeirq fix for duovero parlor making my life a bit easier as that
allows me to run basic PM regression tests on it.
It would be nice to have these in v4.4, but if it gets too late for that
because of the holidays, it is not super critical if these get merged for
v4.5.
* tag 'omap-for-v4.4/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCFPGA DTS update for v4.5, part 2
- clean up mcvevk dts file, replace space with tab
- Disable SDMMC node in base socfpga.dtsi file
* tag 'socfpga_dts_for_v4.5_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Enable MMC support at correct place in the DT
ARM: socfpga: Repair incorrectly applied MCV patch
Signed-off-by: Olof Johansson <olof@lixom.net>
Another new soc - the rk3228 quad-core cortex-a7, a new rk3036 board,
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
* tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the kylin board for rk3036
ARM: dts: rockchip: add the sdio/sdmmc node for rk3036
ARM: dts: rockchip: fix the pinctrl bias settings for rk3036
ARM: dts: rockchip: add eFuse node for rk3188 SoCs
ARM: dts: rockchip: add eFuse node for rk3066a SoCs
ARM: dts: rockchip: add eFuse config of rk3288 SoC
ARM: dts: rockchip: add rk3228-evb board
ARM: dts: rockchip: add core rk3228 dtsi
clk: rockchip: Add the clock ids of rk3288 eFuses
ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name
ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board
ARM: dts: rockchip: move the public part to rk3288-evb common
ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846
ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846
clk: rockchip: add dt-binding header for rk3228
clk: rockchip: add id for mipidsi sclk on rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Add regulators to the scpsys binding.
Move the include of the reset contoller to include/dt-bindings/reset.
Add basic support for mt2701 SoC and evaluation board.
* tag 'v4.4-next-dts' of https://github.com/mbgg/linux-mediatek:
dt-bindings: soc: Add supplies for Mediatek SCPSYS unit
ARM: mediatek: DT: Move reset controller constants into common location
ARM: dts: mediatek: add MT2701 basic support
Document: DT: Add bindings for mediatek MT2701 SoC Platform
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 4.5 (part 3)
Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil
* tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property
ARM: dts: enable GPU for SolidRun's Cubox
ARM: dts: dove: add DT GPU support
ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
ARM: mvebu: add kirkwood compatibles for cloudengine boards
ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC GIC Cleanup for v4.5
On several Renesas ARM SoCs, the GIC is described in DT as being a
Cortex A9 GIC, while it's actually a PL390. This is not only stated in
the documentation, but has been verified by reading the GICD_IIDR
register.
To correct this:
1. Update the DT compatible value to match reality,
2. Update the board staging drivers to match the above.
* tag 'renesas-gic-cleanup-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
staging: board: armadillo800eva: Use "arm,pl390"
staging: board: kzm9d: Use "arm,pl390"
ARM: shmobile: r8a7778 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: emev2 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r8a7740 dtsi: Use "arm,pl390" for GIC
ARM: shmobile: r7s72100 dtsi: Use "arm,pl390" for GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
Third Round of Renesas ARM Based SoC DT Updates for v4.5
* Use SoC-specific usb-dmac and IPMMU compatibility strings
* Add internal delay for i2c IPs
* Add missing serial devices to r8a7793
* Enable DMA for r8a7793 serial devices
* Add serial port config to chosen/stdout-path
* Tidyup #sound-dai-cells settings for r8a7798/bockw
* Remove deprecated #gpio-range-cells from r8a7793
* Add EtherAVB support to r8a7791
* Add MSIOF support to sh73a0
* tag 'renesas-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
ARM: shmobile: r8a779x: use SoC-specific usb-dmac compatibility strings
ARM: shmobile: r8a7794: IPMMU compat string SoC part number update
ARM: shmobile: r8a7793: IPMMU compat string SoC part number update
ARM: shmobile: r8a7791: IPMMU compat string SoC part number update
ARM: shmobile: r8a7790: IPMMU compat string SoC part number update
ARM: shmobile: r8a7794: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7791: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7790: dtsi: add internal delay for i2c IPs
ARM: shmobile: r8a7793: Describe DMA for the serial ports
ARM: shmobile: r8a7793: Add missing serial devices to DT
ARM: shmobile: lager dts: Add serial port config to chosen/stdout-path
ARM: shmobile: porter dts: Add serial port config to chosen/stdout-path
ARM: shmobile: silk dts: Add serial port config to chosen/stdout-path
ARM: shmobile: gose dts: Add serial port config to chosen/stdout-path
ARM: shmobile: bockw dts: Update console parameters
ARM: shmobile: ape6evm dts: Add serial port config to chosen/stdout-path
ARM: shmobile: alt dts: Add serial port config to chosen/stdout-path
ARM: shmobile: koelsch dts: Add serial port config to chosen/stdout-path
ARM: shmobile: r8a7778: tidyup #sound-dai-cells settings
ARM: shmobile: bockw dts: Override #sound-dai-cells to zero
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.4, 3rd round:
- Fix Ethernet PHY mode on i.MX6 Ventana boards, which can result in
a non-functional Ethernet when Marvell phy driver rather than generic
phy driver is selected.
- Fix an assigned-clock configuration bug on imx6qdl-sabreauto board
which was introduced by commit ed339363de ("ARM: dts:
imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously").
* tag 'imx-fixes-4.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
ARM: at91/dt: sama5d4: update i2c compatible string
ARM: at91/dt: sama5d4 master clock can run at 200MHz now
ARM: at91/dt: sama5d2: add watchdog node
ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT changes for 4.5
Allwinner device-tree related patches for the 4.5 merge window.
* Support for the H3
* Addition of the RSB to the relevant devices (sun8i, sun9i)
* Addition of the Video Engine clocks for the older SoCs (sun4i, sun7i)
* Addition of the DRAM gates for the older SoCs (sun4i, sun7i)
* Addition of the audio codec to a bunch of boards
* New board: ICNova SWAC
* tag 'sunxi-dt-for-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (40 commits)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Enable mmc3 (baseboard SD socket)
ARM: dts: sun7i: Olimex A20-SOM-EVB: Add LRADC keys
ARM: dts: sun9i: cubieboard4: Enable Reduced Serial Bus controller
ARM: dts: sun9i: cubieboard4: Enable consumer IR receiver
ARM: dts: sun9i: cubieboard4: Enable LEDs
ARM: dts: sun7i: Add VE (Video Engine) module clock node
ARM: dts: sun4i: Add VE (Video Engine) module clock node
ARM: dts: sun8i: Add Orange Pi Plus support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun7i: Add DRAM gates
ARM: dts: sun4i: Add DRAM gates
ARM: dts: sun9i: Add NMI controller device node
ARM: dts: sun9i: optimus: Enable Reduced Serial Bus controller
ARM: dts: sun9i: Add Reduced Serial Bus controller device node to A80 dtsi
ARM: dts: sun9i: optimus: Enable consumer IR receiver
ARM: dts: sun9i: Add consumer IR receiver device node and pinmux settings
ARM: dts: sun9i: optimus: Enable LED3
ARM: dts: sun9i: Add A80 R_PIO pin controller device node
ARM: dts: sun9i: Add TODO comments for the main and low power clocks
ARM: dts: sun9i: Add A80 PRCM clocks and reset control nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
arm: Xilinx Zynq dt patches for v4.5
- Various small DT changes, GPIO, slcr, cpu label
* tag 'zynq-dt-for-4.5' of https://github.com/Xilinx/linux-xlnx:
ARM: dt: zynq: Add labels to cpu nodes to allow overriding OPPs.
ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
ARM: zynq: DT: Add interrupt-controller property to GPIO
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit adds LCD support for the TS-4800. The panel is an Okaya
RS800480T-7X0WQ and the timings have been extracted from Technologic
Systems' tree.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously, the device tree mapped the FPGA like any other IPs inside
the SoC, but it is actually mapped through the WEIM (Wireless External
Interface Module). This patch updates the device tree to make use of it.
About the timings: in the image provided by the manufacturer, only
CS0GCR1 is changed. The other values are the default ones, but the WEIM
bindings expect them to be all explicitly set in the device tree, so I
just put the default values in the dt.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.
More details here:
http://wiki.embeddedarm.com/wiki/TS-4800
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri standard pinmux for FlexCAN controller instances. CAN
is not a standard Colibri feature, but the datasheet predefines
pins which provide CAN (compatible across some modules). Hence,
add the pinmux on module level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No functional change, just moving the node to the place where it
belongs according to its unit address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This has been moved to the reg property where it belongs for quite some
time. The range has been unused by the kernel since then and with kernel
4.4 it's flagged as an unparsable range, as it does not comply to the
PCI ranges DT binding. Fix this by removing the superfluous range.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
