It is possible that tc stats get checked before the packet we check for
actually arrived into the interface and accounted for.
Fix it by checking for the expected result in a loop until
timeout is reached (by default 1 second).
Fixes: 07e5c75184 ("selftests: forwarding: Introduce tc flower matching tests")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check configurations and packets transference with different variations
of autoneg and speed.
Test plan:
1. Test force of same speed with autoneg off
2. Test force of different speeds with autoneg off (should fail)
3. One side is autoneg on and other side sets force of common speeds
4. One side is autoneg on and other side only advertises a subset of the
common speeds (one speed of the subset)
5. One side is autoneg on and other side only advertises a subset of the
common speeds. Check that highest speed is negotiated
6. Test autoneg on, but each side advertises different speeds (should
fail)
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that waits for device with maximum number of iterations.
It enables to limit the waiting and prevent infinite loop.
This will be used by the subsequent patch which will set two ports to
different speeds in order to make sure they cannot negotiate a link.
Waiting for all the setup is limited with 10 minutes for each device.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions:
1. speeds_arr_get
The function returns an array of speed values from
/usr/include/linux/ethtool.h The array looks as follows:
[10baseT/Half] = 0,
[10baseT/Full] = 1,
...
2. ethtool_set:
params: cmd
The function runs ethtool by cmd (ethtool -s cmd) and checks if
there was an error in configuration
3. dev_speeds_get:
params: dev, with_mode (0 or 1), adver (0 or 1)
return value: Array of supported/Advertised link modes
with/without mode
* Example 1:
speeds_get swp1 0 0
return: 1000 10000 40000
* Example 2:
speeds_get swp1 1 1
return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full
4. common_speeds_get:
params: dev1, dev2, with_mode (0 or 1), adver (0 or 1)
return value: Array of common speeds of dev1 and dev2
* Example:
common_speeds_get swp1 swp2 0 0
return: 1000 10000
Assuming that swp1 supports 1000 10000 40000 and swp2 supports
1000 10000
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an option to check that packets hit the tc filter without providing
the exact number of packets that should hit it.
It is useful while sending many packets in background and checking that
at least one of them hit the tc filter.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add proto parameter in order to enable the use of devlink_trap_cleanup()
in tests that use IPv6 protocol.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2_drops_test() is used to check that drop traps are functioning as
intended. Currently it is only used in the layer 2 test, but it is also
useful for the layer 3 test introduced in the subsequent patch.
l2_drops_cleanup() is used to clean configurations and kill mausezahn
proccess.
Export the functions to the common devlink library to allow it to be
re-used by future tests.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that creates netdevsim instance inside network namespace
and verifies that the related devlink instance and port netdevices
reside in the namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to interact with devlink-trap, such as setting the action of
a trap and retrieving statistics.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tests that create their network interfaces dynamically or do not use
interfaces at all (as with netdevsim) it is useful to define their own
devlink device instead of deriving it from the first network interface.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the jq return value workaround code into a separate helper so it
could be used by the rest of the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TC filters used in the test do not work with veth devices because the
outer Ethertype is 802.1Q and not IPv4. The test passes with mlxsw
netdevs since the hardware always looks at "The first Ethertype that
does not point to either: VLAN, CNTAG or configurable Ethertype".
Fix this by matching on the VLAN ID instead, but on the ingress side.
The reason why this is not performed at egress is explained in the
commit cited below.
Fixes: 541ad323db ("selftests: forwarding: gre_multipath: Update next-hop statistics match criteria")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test did not enable IPv4 forwarding during its setup phase, which
causes the test to fail on machines where IPv4 forwarding is disabled.
Fixes: 54818c4c4b ("selftests: forwarding: Test multipath tunneling")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Tested-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add selftest scripts for multipath hashing on inner IP pkts when there
is a single GRE tunnel but there are multiple underlay routes to reach
the other end of the tunnel.
Four cases are covered in these scripts:
- IPv4 inner, IPv4 outer
- IPv6 inner, IPv4 outer
- IPv4 inner, IPv6 outer
- IPv6 inner, IPv6 outer
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tc_flower to test plain ingress device matching and also
tc_shblock to test ingress device matching on shared block.
Add new tc_flower_router.sh where ingress device matching on egress
(after routing) is done.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a version of router_multipath.sh that uses nexthop objects for
routes.
Ido requested a version that does not cause regressions with mlxsw
testing since it does not support nexthop objects yet.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl setting bc_forwarding for $rp2 is needed when ping_test_from h2,
otherwise the bc packets from $rp2 won't be forwarded. This patch is to
add this setting for $rp2.
Also, as ping_test_from does grep "$from" only, which could match some
unexpected output, some test case doesn't really work, like:
# ping_test_from $h2 198.51.200.255 198.51.200.2
PING 198.51.200.255 from 198.51.100.2 veth3: 56(84) bytes of data.
64 bytes from 198.51.100.1: icmp_seq=1 ttl=64 time=0.336 ms
When doing grep $form (198.51.200.2), the output could still match.
So change to grep "bytes from $from" instead.
Fixes: 40f98b9af9 ("selftests: add a selftest for directed broadcast forwarding")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is split in two, the first part checks if a report creates a
corresponding mdb entry and if traffic is properly forwarded to it, and
the second part checks if the mdb entry is deleted after a leave and
if traffic is *not* forwarded to it. Since the mcast querier is enabled
we should see standard mcast snooping bridge behaviour.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Construct a basic topology consisting of two hosts connected using a
VLAN-aware bridge. Put each port in a different VLAN and test that ping
fails.
Add ingress and egress filters with a VLAN modify action and test that
ping passes.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send packets with VLAN and PCP set and check that TC flower filters can
match on these keys.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a packet is routed using a multicast route whose specified
ingress interface does not match the interface from which the packet was
received, the packet is dropped.
Add IPv4 and IPv6 test cases for above mentioned scenario.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the forwarding selftests to work, we need network namespaces when
using veth/vrf otherwise ping/ping6 commands like these:
ip vrf exec vveth0 /bin/ping 192.0.2.2 -c 10 -i 0.1 -w 5
will fail because network namespaces may not be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global variable RET needs to be initialized before each call to
log_test. This test case sets it once before running the tests, but then
calls log_tests for every individual test. Thus a failure in one of the
tests causes spurious failures in follow-up tests as well.
Fix by moving the initialization of RET from test_all() to
full_test_span_gre_dir_acl(), a function that implements the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test sets up mirroring such that it mirrors all overlay traffic.
That includes ARP, which causes occasional miscounts and spurious
failures. Ignore ARP explicitly to avoid these problems.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test relies on routing in the primary traffic path, but neglects to
enable forwarding. Do so.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After one LAG slave is downed and another upped, it takes a while for
the neighbor on a bridge to time out and get renegotiated. The test does
prompt update of FDB entries by arpinging. But because the neighbor
still references another address, offloading is not possible, and some
packets may end up not being mirrored.
To force the neighbor renegotiation, simply flush the neighbor table at
the bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARP or ND traffic can cause spurious migration of FDB back to $swp3.
Mirroring is then updated in accordance with the change, and mirrored
packets are seen at h3, causing a failure.
Detect the case of this spurious roaming, and retry the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged egress test sets up mirroring to {,ip6}gretap such that the
underlay goes through a bridge. Then VLAN flags are manipulated to test
that the traffic leaves the bridge 802.1q-tagged or not, as appropriate.
However, when a neighbor expires at the time that the bridge VLAN is
configured as PVID and egress untagged, the following discovery process
can't finish, because the IP address on H3 is still at the VLAN-tagged
netdevice. This manifests by occasional failures where only several of
the 10 required packets get through.
Therefore, when reconfiguring the VLAN flags, move the IP address to the
appropriate device in the H3 VRF.
In addition to that, take this opportunity to embed an ASCII art diagram
to make the topology move obvious.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in an environment with poor performance (such as a
simulator), processing mirrored packets can take a while. Evaluating the
condition too soon leads to spurious "seen 9, expected 10" failures as
the last packet doesn't have enough time to get mirrored and the mirror
to arrive and bump the observed counters.
Wait for one ping interval before evaluating the test.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a simulator, the TTL change takes a while to settle and
during this time the performance of the packet processing is lowered.
The resulting instability leads to ping sending more packets as it
assumes some have been dropped. This then leads to regular spurious
failures as more packets than expected are observed.
Sleep a bit to give the system time to stabilize.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ping intervals are too short for running mirroring tests in
simulator. This leads to ping sending a follow-up ping before the reply
arrives, thus sending more than the requested 10 ICMP requests. Those
are mirrored, and over a certain threshold the test case run is
considered a failure, because too much traffic is observed.
Bump interval and timeout numbers 5x in mirroring tests to address the
spurious failures.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timeout (2 seconds) proved to be too low for some (emulated)
systems where we run the tests.
Make the timeout configurable and default to 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARP suppression allows the Linux bridge to answer ARP requests on behalf
of remote hosts. It reduces the amount of packets a VTEP needs to flood.
This test verifies that ARP suppression on / off works when a neighbour
exists and when it does not exist. It does so by sending an ARP request
from a host connected to one VTEP and checking whether it was received
by a second VTEP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VXLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI. Different tenants
(VRFs) use different L3 VNIs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that ARP packets are correctly decapsulated by the ingress VTEP
by removing the neighbours configured on both VLAN interfaces and
running a ping test.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In asymmetric routing the ingress VTEP routes the packet into the
correct VXLAN tunnel, whereas the egress VTEP only bridges the packet to
the correct host. Therefore, packets in different directions use
different VNIs - the target VNI.
The test uses a simple topology with two VTEPs and two VNIs and verifies
that ping passes between hosts (local / remote) in the same VLAN (VNI)
and in different VLANs belonging to the same tenant (VRF).
While the test does not check VM mobility, it does configure an anycast
gateway using a macvlan device on both VTEPs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
