POWER9 Witherspoon machines come with 4 or 6 V100 GPUs which are not
pluggable PCIe devices but still have PCIe links which are used
for config space and MMIO. In addition to that the GPUs have 6 NVLinks
which are connected to other GPUs and the POWER9 CPU. POWER9 chips
have a special unit on a die called an NPU which is an NVLink2 host bus
adapter with p2p connections to 2 to 3 GPUs, 3 or 2 NVLinks to each.
These systems also support ATS (address translation services) which is
a part of the NVLink2 protocol. Such GPUs also share on-board RAM
(16GB or 32GB) to the system via the same NVLink2 so a CPU has
cache-coherent access to a GPU RAM.
This exports GPU RAM to the userspace as a new VFIO device region. This
preregisters the new memory as device memory as it might be used for DMA.
This inserts pfns from the fault handler as the GPU memory is not onlined
until the vendor driver is loaded and trained the NVLinks so doing this
earlier causes low level errors which we fence in the firmware so
it does not hurt the host system but still better be avoided; for the same
reason this does not map GPU RAM into the host kernel (usual thing for
emulated access otherwise).
This exports an ATSD (Address Translation Shootdown) register of NPU which
allows TLB invalidations inside GPU for an operating system. The register
conveniently occupies a single 64k page. It is also presented to
the userspace as a new VFIO device region. One NPU has 8 ATSD registers,
each of them can be used for TLB invalidation in a GPU linked to this NPU.
This allocates one ATSD register per an NVLink bridge allowing passing
up to 6 registers. Due to the host firmware bug (just recently fixed),
only 1 ATSD register per NPU was actually advertised to the host system
so this passes that alone register via the first NVLink bridge device in
the group which is still enough as QEMU collects them all back and
presents to the guest via vPHB to mimic the emulated NPU PHB on the host.
In order to provide the userspace with the information about GPU-to-NVLink
connections, this exports an additional capability called "tgt"
(which is an abbreviated host system bus address). The "tgt" property
tells the GPU its own system address and allows the guest driver to
conglomerate the routing information so each GPU knows how to get directly
to the other GPUs.
For ATS to work, the nest MMU (an NVIDIA block in a P9 CPU) needs to
know LPID (a logical partition ID or a KVM guest hardware ID in other
words) and PID (a memory context ID of a userspace process, not to be
confused with a linux pid). This assigns a GPU to LPID in the NPU and
this is why this adds a listener for KVM on an IOMMU group. A PID comes
via NVLink from a GPU and NPU uses a PID wildcard to pass it through.
This requires coherent memory and ATSD to be available on the host as
the GPU vendor only supports configurations with both features enabled
and other configurations are known not to work. Because of this and
because of the ways the features are advertised to the host system
(which is a device tree with very platform specific properties),
this requires enabled POWERNV platform.
The V100 GPUs do not advertise any of these capabilities via the config
space and there are more than just one device ID so this relies on
the platform to tell whether these GPUs have special abilities such as
NVLinks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Support for destination MAC in ipset, from Stefano Brivio.
2) Disallow all-zeroes MAC address in ipset, also from Stefano.
3) Add IPSET_CMD_GET_BYNAME and IPSET_CMD_GET_BYINDEX commands,
introduce protocol version number 7, from Jozsef Kadlecsik.
A follow up patch to fix ip_set_byindex() is also included
in this batch.
4) Honor CTA_MARK_MASK from ctnetlink, from Andreas Jaggi.
5) Statify nf_flow_table_iterate(), from Taehee Yoo.
6) Use nf_flow_table_iterate() to simplify garbage collection in
nf_flow_table logic, also from Taehee Yoo.
7) Don't use _bh variants of call_rcu(), rcu_barrier() and
synchronize_rcu_bh() in Netfilter, from Paul E. McKenney.
8) Remove NFC_* cache definition from the old caching
infrastructure.
9) Remove layer 4 port rover in NAT helpers, use random port
instead, from Florian Westphal.
10) Use strscpy() in ipset, from Qian Cai.
11) Remove NF_NAT_RANGE_PROTO_RANDOM_FULLY branch now that
random port is allocated by default, from Xiaozhou Liu.
12) Ignore NF_NAT_RANGE_PROTO_RANDOM too, from Florian Westphal.
13) Limit port allocation selection routine in NAT to avoid
softlockup splats when most ports are in use, from Florian.
14) Remove unused parameters in nf_ct_l4proto_unregister_sysctl()
from Yafang Shao.
15) Direct call to nf_nat_l4proto_unique_tuple() instead of
indirection, from Florian Westphal.
16) Several patches to remove all layer 4 NAT indirections,
remove nf_nat_l4proto struct, from Florian Westphal.
17) Fix RTP/RTCP source port translation when SNAT is in place,
from Alin Nastac.
18) Selective rule dump per chain, from Phil Sutter.
19) Revisit CLUSTERIP target, this includes a deadlock fix from
netns path, sleep in atomic, remove bogus WARN_ON_ONCE()
and disallow mismatching IP address and MAC address.
Patchset from Taehee Yoo.
20) Update UDP timeout to stream after 2 seconds, from Florian.
21) Shrink UDP established timeout to 120 seconds like TCP timewait.
22) Sysctl knobs to set GRE timeouts, from Yafang Shao.
23) Move seq_print_acct() to conntrack core file, from Florian.
24) Add enum for conntrack sysctl knobs, also from Florian.
25) Place nf_conntrack_acct, nf_conntrack_helper, nf_conntrack_events
and nf_conntrack_timestamp knobs in the core, from Florian Westphal.
As a side effect, shrink netns_ct structure by removing obsolete
sysctl anchors, also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-21
The following pull-request contains BPF updates for your *net-next* tree.
There is a merge conflict in test_verifier.c. Result looks as follows:
[...]
},
{
"calls: cross frame pruning",
.insns = {
[...]
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "function calls to other bpf functions are allowed for root only",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
{
"jset: functional",
.insns = {
[...]
{
"jset: unknown const compare not taken",
.insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
BPF_FUNC_get_prandom_u32),
BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
BPF_EXIT_INSN(),
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "!read_ok",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
[...]
{
"jset: range",
.insns = {
[...]
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.result_unpriv = ACCEPT,
.result = ACCEPT,
},
The main changes are:
1) Various BTF related improvements in order to get line info
working. Meaning, verifier will now annotate the corresponding
BPF C code to the error log, from Martin and Yonghong.
2) Implement support for raw BPF tracepoints in modules, from Matt.
3) Add several improvements to verifier state logic, namely speeding
up stacksafe check, optimizations for stack state equivalence
test and safety checks for liveness analysis, from Alexei.
4) Teach verifier to make use of BPF_JSET instruction, add several
test cases to kselftests and remove nfp specific JSET optimization
now that verifier has awareness, from Jakub.
5) Improve BPF verifier's slot_type marking logic in order to
allow more stack slot sharing, from Jiong.
6) Add sk_msg->size member for context access and add set of fixes
and improvements to make sock_map with kTLS usable with openssl
based applications, from John.
7) Several cleanups and documentation updates in bpftool as well as
auto-mount of tracefs for "bpftool prog tracelog" command,
from Quentin.
8) Include sub-program tags from now on in bpf_prog_info in order to
have a reliable way for user space to get all tags of the program
e.g. needed for kallsyms correlation, from Song.
9) Add BTF annotations for cgroup_local_storage BPF maps and
implement bpf fs pretty print support, from Roman.
10) Fix bpftool in order to allow for cross-compilation, from Ivan.
11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
to be compatible with libbfd and allow for Debian packaging,
from Jakub.
12) Remove an obsolete prog->aux sanitation in dump and get rid of
version check for prog load, from Daniel.
13) Fix a memory leak in libbpf's line info handling, from Prashant.
14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
does not get unaligned, from Jesper.
15) Fix test_progs kselftest to work with older compilers which are less
smart in optimizing (and thus throwing build error), from Stanislav.
16) Cleanup and simplify AF_XDP socket teardown, from Björn.
17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a method for query port under the uverbs global methods. Current
ib_port_attr struct is passed as a single attribute and port_cap_flags2 is
added as a new attribute to the function.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
port_cap_flags2 represents IBTA PortInfo:CapabilityMask2.
The field safely extends the RDMA_NLDEV_ATTR_CAP_FLAGS operand as it was
exported as 64 bit to allow this kind of extension.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the mount namespace code that implements mount(2) should be using the
MS_* flags. Suppress them inside the kernel unless uapi/linux/mount.h is
included.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
Pull networking fixes from David Miller:
1) Off by one in netlink parsing of mac802154_hwsim, from Alexander
Aring.
2) nf_tables RCU usage fix from Taehee Yoo.
3) Flow dissector needs nhoff and thoff clamping, from Stanislav
Fomichev.
4) Missing sin6_flowinfo initialization in SCTP, from Xin Long.
5) Spectrev1 in ipmr and ip6mr, from Gustavo A. R. Silva.
6) Fix r8169 crash when DEBUG_SHIRQ is enabled, from Heiner Kallweit.
7) Fix SKB leak in rtlwifi, from Larry Finger.
8) Fix state pruning in bpf verifier, from Jakub Kicinski.
9) Don't handle completely duplicate fragments as overlapping, from
Michal Kubecek.
10) Fix memory corruption with macb and 64-bit DMA, from Anssi Hannula.
11) Fix TCP fallback socket release in smc, from Myungho Jung.
12) gro_cells_destroy needs to napi_disable, from Lorenzo Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (130 commits)
rds: Fix warning.
neighbor: NTF_PROXY is a valid ndm_flag for a dump request
net: mvpp2: fix the phylink mode validation
net/sched: cls_flower: Remove old entries from rhashtable
net/tls: allocate tls context using GFP_ATOMIC
iptunnel: make TUNNEL_FLAGS available in uapi
gro_cell: add napi_disable in gro_cells_destroy
lan743x: Remove MAC Reset from initialization
net/mlx5e: Remove the false indication of software timestamping support
net/mlx5: Typo fix in del_sw_hw_rule
net/mlx5e: RX, Fix wrong early return in receive queue poll
ipv6: explicitly initialize udp6_addr in udp_sock_create6()
bnxt_en: Fix ethtool self-test loopback.
net/rds: remove user triggered WARN_ON in rds_sendmsg
net/rds: fix warn in rds_message_alloc_sgs
ath10k: skip sending quiet mode cmd for WCN3990
mac80211: free skb fraglist before freeing the skb
nl80211: fix memory leak if validate_pae_over_nl80211() fails
net/smc: fix TCP fallback socket release
vxge: ensure data0 is initialized in when fetching firmware version information
...
ip l add dev tun type gretap external
ip r a 10.0.0.1 encap ip dst 192.168.152.171 id 1000 dev gretap
For gretap Key example when the command set the id but don't set the
TUNNEL_KEY flags. There is no key field in the send packet
In the lwtunnel situation, some TUNNEL_FLAGS should can be set by
userspace
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
vhost structs are shared by vhost-kernel and vhost-user. Split them
into a separate file to ease copying them into programs that implement
either the server or the client side of vhost-user.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In commit 88c85538, "virtio-blk: add discard and write zeroes features
to specification" (https://github.com/oasis-tcs/virtio-spec), the virtio
block specification has been extended to add VIRTIO_BLK_T_DISCARD and
VIRTIO_BLK_T_WRITE_ZEROES commands. This patch enables support for
discard and write zeroes in the virtio-blk driver when the device
advertises the corresponding features, VIRTIO_BLK_F_DISCARD and
VIRTIO_BLK_F_WRITE_ZEROES.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Signed-off-by: Daniel Verkamp <dverkamp@chromium.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed at Linux Plumbers Conference 2018 in Vancouver [1] this is the
implementation of binderfs.
/* Abstract */
binderfs is a backwards-compatible filesystem for Android's binder ipc
mechanism. Each ipc namespace will mount a new binderfs instance. Mounting
binderfs multiple times at different locations in the same ipc namespace
will not cause a new super block to be allocated and hence it will be the
same filesystem instance.
Each new binderfs mount will have its own set of binder devices only
visible in the ipc namespace it has been mounted in. All devices in a new
binderfs mount will follow the scheme binder%d and numbering will always
start at 0.
/* Backwards compatibility */
Devices requested in the Kconfig via CONFIG_ANDROID_BINDER_DEVICES for the
initial ipc namespace will work as before. They will be registered via
misc_register() and appear in the devtmpfs mount. Specifically, the
standard devices binder, hwbinder, and vndbinder will all appear in their
standard locations in /dev. Mounting or unmounting the binderfs mount in
the initial ipc namespace will have no effect on these devices, i.e. they
will neither show up in the binderfs mount nor will they disappear when the
binderfs mount is gone.
/* binder-control */
Each new binderfs instance comes with a binder-control device. No other
devices will be present at first. The binder-control device can be used to
dynamically allocate binder devices. All requests operate on the binderfs
mount the binder-control device resides in.
Assuming a new instance of binderfs has been mounted at /dev/binderfs
via mount -t binderfs binderfs /dev/binderfs. Then a request to create a
new binder device can be made as illustrated in [2].
Binderfs devices can simply be removed via unlink().
/* Implementation details */
- dynamic major number allocation:
When binderfs is registered as a new filesystem it will dynamically
allocate a new major number. The allocated major number will be returned
in struct binderfs_device when a new binder device is allocated.
- global minor number tracking:
Minor are tracked in a global idr struct that is capped at
BINDERFS_MAX_MINOR. The minor number tracker is protected by a global
mutex. This is the only point of contention between binderfs mounts.
- struct binderfs_info:
Each binderfs super block has its own struct binderfs_info that tracks
specific details about a binderfs instance:
- ipc namespace
- dentry of the binder-control device
- root uid and root gid of the user namespace the binderfs instance
was mounted in
- mountable by user namespace root:
binderfs can be mounted by user namespace root in a non-initial user
namespace. The devices will be owned by user namespace root.
- binderfs binder devices without misc infrastructure:
New binder devices associated with a binderfs mount do not use the
full misc_register() infrastructure.
The misc_register() infrastructure can only create new devices in the
host's devtmpfs mount. binderfs does however only make devices appear
under its own mountpoint and thus allocates new character device nodes
from the inode of the root dentry of the super block. This will have
the side-effect that binderfs specific device nodes do not appear in
sysfs. This behavior is similar to devpts allocated pts devices and
has no effect on the functionality of the ipc mechanism itself.
[1]: https://goo.gl/JL2tfX
[2]: program to allocate a new binderfs binder device:
#define _GNU_SOURCE
#include <errno.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/ioctl.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <unistd.h>
#include <linux/android/binder_ctl.h>
int main(int argc, char *argv[])
{
int fd, ret, saved_errno;
size_t len;
struct binderfs_device device = { 0 };
if (argc < 2)
exit(EXIT_FAILURE);
len = strlen(argv[1]);
if (len > BINDERFS_MAX_NAME)
exit(EXIT_FAILURE);
memcpy(device.name, argv[1], len);
fd = open("/dev/binderfs/binder-control", O_RDONLY | O_CLOEXEC);
if (fd < 0) {
printf("%s - Failed to open binder-control device\n",
strerror(errno));
exit(EXIT_FAILURE);
}
ret = ioctl(fd, BINDER_CTL_ADD, &device);
saved_errno = errno;
close(fd);
errno = saved_errno;
if (ret < 0) {
printf("%s - Failed to allocate new binder device\n",
strerror(errno));
exit(EXIT_FAILURE);
}
printf("Allocated new binder device with major %d, minor %d, and "
"name %s\n", device.major, device.minor,
device.name);
exit(EXIT_SUCCESS);
}
Cc: Martijn Coenen <maco@android.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) promote bpf_perf_event.h to mandatory UAPI header, from Masahiro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Herton reports the following error when building a userspace program that
includes net_stamp.h:
In file included from foo.c:2:
/usr/include/linux/net_tstamp.h:158:2: error: unknown type name
‘clockid_t’
clockid_t clockid; /* reference clockid */
^~~~~~~~~
Fix it by using __kernel_clockid_t in place of clockid_t.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Cc: Timothy Redaelli <tredaelli@redhat.com>
Reported-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fix from Jens Axboe:
"Correct an ioctl direction for the zoned ioctls"
* tag 'for-linus-20181218' of git://git.kernel.dk/linux-block:
uapi: linux/blkzoned.h: fix BLKGETZONESZ and BLKGETNRZONES definitions
This adds metadata to sk_msg_md for BPF programs to read the sk_msg
size.
When the SK_MSG program is running under an application that is using
sendfile the data is not copied into sk_msg buffers by default. Rather
the BPF program uses sk_msg_pull_data to read the bytes in. This
avoids doing the costly memcopy instructions when they are not in
fact needed. However, if we don't know the size of the sk_msg we
have to guess if needed bytes are available by doing a pull request
which may fail. By including the size of the sk_msg BPF programs can
check the size before issuing sk_msg_pull_data requests.
Additionally, the same applies for sendmsg calls when the application
provides multiple iovs. Here the BPF program needs to pull in data
to update data pointers but its not clear where the data ends without
a size parameter. In many cases "guessing" is not easy to do
and results in multiple calls to pull and without bounded loops
everything gets fairly tricky.
Clean this up by including a u32 size field. Note, all writes into
sk_msg_md are rejected already from sk_msg_is_valid_access so nothing
additional is needed there.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add new ioctl method for the MR object - ADVISE_MR.
This command can be used by users to give an advice or directions to the
kernel about an address range that belongs to memory regions.
A new ib_device callback, advise_mr(), is introduced here to suupport the
new command. This command takes the following arguments:
- pd: The protection domain to which all memory regions belong
- advice: The type of the advice
* IB_UVERBS_ADVISE_MR_ADVICE_PREFETCH - Pre-fetch a range of
an on-demand paging MR
* IB_UVERBS_ADVISE_MR_ADVICE_PREFETCH_WRITE - Pre-fetch a range
of an on-demand paging MR with write intention
- flags: The properties of the advice
* IB_UVERBS_ADVISE_MR_FLAG_FLUSH - Operation must end before
return to the caller
- sg_list: The list of memory ranges
- num_sge: The number of memory ranges in the list
- attrs: More attributes to be parsed by the provider
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Guy Levi <guyle@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add an ioctl method to destroy the PD, MR, MW, AH, flow, RWQ indirection
table and XRCD objects by handle which doesn't require any output response
during destruction.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce a helper function gather_objects_handle() to copy object handles
under a spin lock.
Expose these objects handles via the uverbs ioctl interface.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Now that the handlers do not process their own udata we can make a
sensible ioctl that wrappers them. The ioctl follows the same format as
the write_ex() and has the user explicitly specify the core and driver
in/out opaque structures and a command number.
This works for all forms of write commands.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ASoC: Updates for v4.21
Not much work on the core this time around but we've seen quite a bit of
driver work, including on the generic DT drivers. There's also a large
part of the diff from a merge of the DaVinci and OMAP directories, along
with some active development there:
- Preparatory work from Morimoto-san for merging the audio-graph and
audio-graph-scu cards.
- A merge of the TI OMAP and DaVinci directories, the OMAP product line
has been merged into the DaVinci product line so there is now a lot
of IP sharing which meant that the split directories just got in the
way. This has pulled in a few architecture changes as well.
- A big cleanup of the Maxim MAX9867 driver from Ladislav Michl.
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx I2S
controllers.
Currently radar detection and corresponding channel switch is handled
at the AP device. STA ignores these detected radar events since the
radar signal can be seen mostly by the AP as well. But in scenarios where
a radar signal is seen only at STA, notifying this event to the AP which
can trigger a channel switch can be useful.
Stations can report such radar events autonomously through Spectrum
management (Measurement Report) action frame to its AP. The userspace on
processing the report can notify the kernel with the use of the added
NL80211_CMD_NOTIFY_RADAR to indicate the detected event and inturn adding
the reported channel to NOL.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The older code and current userspace assumed that this data
is the content of the Measurement Report element, starting
with the Measurement Token. Clarify this in the documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixed two issues with BTF. One is related to
struct/union bitfield encoding and the other is related to
forward type.
Issue #1 and solution:
======================
Current btf encoding of bitfield follows what pahole generates.
For each bitfield, pahole will duplicate the type chain and
put the bitfield size at the final int or enum type.
Since the BTF enum type cannot encode bit size,
pahole workarounds the issue by generating
an int type whenever the enum bit size is not 32.
For example,
-bash-4.4$ cat t.c
typedef int ___int;
enum A { A1, A2, A3 };
struct t {
int a[5];
___int b:4;
volatile enum A c:4;
} g;
-bash-4.4$ gcc -c -O2 -g t.c
The current kernel supports the following BTF encoding:
$ pahole -JV t.o
[1] TYPEDEF ___int type_id=2
[2] INT int size=4 bit_offset=0 nr_bits=32 encoding=SIGNED
[3] ENUM A size=4 vlen=3
A1 val=0
A2 val=1
A3 val=2
[4] STRUCT t size=24 vlen=3
a type_id=5 bits_offset=0
b type_id=9 bits_offset=160
c type_id=11 bits_offset=164
[5] ARRAY (anon) type_id=2 index_type_id=2 nr_elems=5
[6] INT sizetype size=8 bit_offset=0 nr_bits=64 encoding=(none)
[7] VOLATILE (anon) type_id=3
[8] INT int size=1 bit_offset=0 nr_bits=4 encoding=(none)
[9] TYPEDEF ___int type_id=8
[10] INT (anon) size=1 bit_offset=0 nr_bits=4 encoding=SIGNED
[11] VOLATILE (anon) type_id=10
Two issues are in the above:
. by changing enum type to int, we lost the original
type information and this will not be ideal later
when we try to convert BTF to a header file.
. the type duplication for bitfields will cause
BTF bloat. Duplicated types cannot be deduplicated
later if the bitfield size is different.
To fix this issue, this patch implemented a compatible
change for BTF struct type encoding:
. the bit 31 of struct_type->info, previously reserved,
now is used to indicate whether bitfield_size is
encoded in btf_member or not.
. if bit 31 of struct_type->info is set,
btf_member->offset will encode like:
bit 0 - 23: bit offset
bit 24 - 31: bitfield size
if bit 31 is not set, the old behavior is preserved:
bit 0 - 31: bit offset
So if the struct contains a bit field, the maximum bit offset
will be reduced to (2^24 - 1) instead of MAX_UINT. The maximum
bitfield size will be 256 which is enough for today as maximum
bitfield in compiler can be 128 where int128 type is supported.
This kernel patch intends to support the new BTF encoding:
$ pahole -JV t.o
[1] TYPEDEF ___int type_id=2
[2] INT int size=4 bit_offset=0 nr_bits=32 encoding=SIGNED
[3] ENUM A size=4 vlen=3
A1 val=0
A2 val=1
A3 val=2
[4] STRUCT t kind_flag=1 size=24 vlen=3
a type_id=5 bitfield_size=0 bits_offset=0
b type_id=1 bitfield_size=4 bits_offset=160
c type_id=7 bitfield_size=4 bits_offset=164
[5] ARRAY (anon) type_id=2 index_type_id=2 nr_elems=5
[6] INT sizetype size=8 bit_offset=0 nr_bits=64 encoding=(none)
[7] VOLATILE (anon) type_id=3
Issue #2 and solution:
======================
Current forward type in BTF does not specify whether the original
type is struct or union. This will not work for type pretty print
and BTF-to-header-file conversion as struct/union must be specified.
$ cat tt.c
struct t;
union u;
int foo(struct t *t, union u *u) { return 0; }
$ gcc -c -g -O2 tt.c
$ pahole -JV tt.o
[1] INT int size=4 bit_offset=0 nr_bits=32 encoding=SIGNED
[2] FWD t type_id=0
[3] PTR (anon) type_id=2
[4] FWD u type_id=0
[5] PTR (anon) type_id=4
To fix this issue, similar to issue #1, type->info bit 31
is used. If the bit is set, it is union type. Otherwise, it is
a struct type.
$ pahole -JV tt.o
[1] INT int size=4 bit_offset=0 nr_bits=32 encoding=SIGNED
[2] FWD t kind_flag=0 type_id=0
[3] PTR (anon) kind_flag=0 type_id=2
[4] FWD u kind_flag=1 type_id=0
[5] PTR (anon) kind_flag=0 type_id=4
Pahole/LLVM change:
===================
The new kind_flag functionality has been implemented in pahole
and llvm:
https://github.com/yonghong-song/pahole/tree/bitfieldhttps://github.com/yonghong-song/llvm/tree/bitfield
Note that pahole hasn't implemented func/func_proto kind
and .BTF.ext. So to print function signature with bpftool,
the llvm compiler should be used.
Fixes: 69b693f0ae ("bpf: btf: Introduce BPF Type Format (BTF)")
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
syscall_get_arch() is required to be implemented on all architectures
in order to extend the generic ptrace API with PTRACE_GET_SYSCALL_INFO
request.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
This should never have been defined in the arch tree to begin with,
and now uapi/linux/audit.h header is going to use EM_XTENSA
in order to define AUDIT_ARCH_XTENSA which is needed to implement
syscall_get_arch() which in turn is required to extend
the generic ptrace API with PTRACE_GET_SYSCALL_INFO request.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Elvira Khabirova <lineprinter@altlinux.org>
Cc: Eugene Syromyatnikov <esyr@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Existing libraries and tracing frameworks work around this kernel
version check by automatically deriving the kernel version from
uname(3) or similar such that the user does not need to do it
manually; these workarounds also make the version check useless
at the same time.
Moreover, most other BPF tracing types enabling bpf_probe_read()-like
functionality have /not/ adapted this check, and in general these
days it is well understood anyway that all the tracing programs are
not stable with regards to future kernels as kernel internal data
structures are subject to change from release to release.
Back at last netconf we discussed [0] and agreed to remove this
check from bpf_prog_load() and instead document it here in the uapi
header that there is no such guarantee for stable API for these
programs.
[0] http://vger.kernel.org/netconf2018_files/DanielBorkmann_netconf2018.pdf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since commit c895f6f703 ("bpf: correct broken uapi for
BPF_PROG_TYPE_PERF_EVENT program type"), all architectures
(except um) are required to have bpf_perf_event.h in uapi/asm.
Add it to mandatory-y so "make headers_install" can check it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linux 4.20-rc7
* tag 'v4.20-rc7': (403 commits)
Linux 4.20-rc7
scripts/spdxcheck.py: always open files in binary mode
checkstack.pl: fix for aarch64
userfaultfd: check VM_MAYWRITE was set after verifying the uffd is registered
fs/iomap.c: get/put the page in iomap_page_create/release()
hugetlbfs: call VM_BUG_ON_PAGE earlier in free_huge_page()
memblock: annotate memblock_is_reserved() with __init_memblock
psi: fix reference to kernel commandline enable
arch/sh/include/asm/io.h: provide prototypes for PCI I/O mapping in asm/io.h
mm/sparse: add common helper to mark all memblocks present
mm: introduce common STRUCT_PAGE_MAX_SHIFT define
alpha: fix hang caused by the bootmem removal
XArray: Fix xa_alloc when id exceeds max
drm/vmwgfx: Protect from excessive execbuf kernel memory allocations v3
MAINTAINERS: Daniel for drm co-maintainer
drm/amdgpu: drop fclk/gfxclk ratio setting
IB/core: Fix oops in netdev_next_upper_dev_rcu()
dm thin: bump target version
drm/vmwgfx: remove redundant return ret statement
drm/i915: Flush GPU relocs harder for gen3
...
This field is going to be used when the user wants to change the UUID
of the filesystem without having to rewrite all metadata blocks. This
field adds another level of indirection such that when the FSID is
changed what really happens is the current UUID (the one with which the
fs was created) is copied to the 'metadata_uuid' field in the superblock
as well as a new incompat flag is set METADATA_UUID. When the kernel
detects this flag is set it knows that the superblock in fact has 2
UUIDs:
1. Is the UUID which is user-visible, currently known as FSID.
2. Metadata UUID - this is the UUID which is stamped into all on-disk
datastructures belonging to this file system.
When the new incompat flag is present device scanning checks whether
both fsid/metadata_uuid of the scanned device match any of the
registered filesystems. When the flag is not set then both UUIDs are
equal and only the FSID is retained on disk, metadata_uuid is set only
in-memory during mount.
Additionally a new metadata_uuid field is also added to the fs_info
struct. It's initialised either with the FSID in case METADATA_UUID
incompat flag is not set or with the metdata_uuid of the superblock
otherwise.
This commit introduces the new fields as well as the new incompat flag
and switches all users of the fsid to the new logic.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor updates in comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
If we use it this way, people should know about it. Also, replace
true/false with nonzero/zero because the flag is not strictly a bool
anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the documentation in include/uapi/asm-generic/ioctl.h,
_IOW means userspace is writing and kernel is reading, and
_IOR means userspace is reading and kernel is writing.
In case of these two ioctls, kernel is writing and userspace is reading,
so they have to be _IOR instead of _IOW.
Fixes: 72cd87576d ("block: Introduce BLKGETZONESZ ioctl")
Fixes: 65e4e3eee8 ("block: Introduce BLKGETNRZONES ioctl")
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measuring particulate matter in ug / m3 (micro-grams per cubic meter)
is de facto standard. Existing air quality sensors usually follow
this convention and are capable of returning measurements using
this unit.
IIO currently does not offer suitable channel type for this
type of measurements hence this patch adds this.
In addition, extra modifiers are introduced used for distinguishing
between fine pm1, pm2p5 and coarse pm4, pm10 particle measurements, i.e
IIO_MOD_PM1, IIO_MOD_PM25 and IIO_MOD_PM4, IIO_MOD_PM10.
pmX consists of particles with aerodynamic diameter less or equal to
X micrometers.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.
While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETLINK_DUMP_STRICT_CHK can be used for all GET requests,
dumps as well as doit handlers. Replace the DUMP in the
name with GET make that clearer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With every new Hyper-V Enlightenment we implement we're forced to add a
KVM_CAP_HYPERV_* capability. While this approach works it is fairly
inconvenient: the majority of the enlightenments we do have corresponding
CPUID feature bit(s) and userspace has to know this anyways to be able to
expose the feature to the guest.
Add KVM_GET_SUPPORTED_HV_CPUID ioctl (backed by KVM_CAP_HYPERV_CPUID, "one
cap to rule them all!") returning all Hyper-V CPUID feature leaves.
Using the existing KVM_GET_SUPPORTED_CPUID doesn't seem to be possible:
Hyper-V CPUID feature leaves intersect with KVM's (e.g. 0x40000000,
0x40000001) and we would probably confuse userspace in case we decide to
return these twice.
KVM_CAP_HYPERV_CPUID's number is interim: we're intended to drop
KVM_CAP_HYPERV_STIMER_DIRECT and use its number instead.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are two problems with KVM_GET_DIRTY_LOG. First, and less important,
it can take kvm->mmu_lock for an extended period of time. Second, its user
can actually see many false positives in some cases. The latter is due
to a benign race like this:
1. KVM_GET_DIRTY_LOG returns a set of dirty pages and write protects
them.
2. The guest modifies the pages, causing them to be marked ditry.
3. Userspace actually copies the pages.
4. KVM_GET_DIRTY_LOG returns those pages as dirty again, even though
they were not written to since (3).
This is especially a problem for large guests, where the time between
(1) and (3) can be substantial. This patch introduces a new
capability which, when enabled, makes KVM_GET_DIRTY_LOG not
write-protect the pages it returns. Instead, userspace has to
explicitly clear the dirty log bits just before using the content
of the page. The new KVM_CLEAR_DIRTY_LOG ioctl can also operate on a
64-page granularity rather than requiring to sync a full memslot;
this way, the mmu_lock is taken for small amounts of time, and
only a small amount of time will pass between write protection
of pages and the sending of their content.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The V4L2_BUF_TYPE_META_OUTPUT mirrors the V4L2_BUF_TYPE_META_CAPTURE with
the exception that it is an OUTPUT type. The use case for this is to pass
buffers to the device that are not image data but metadata. The formats,
just as the metadata capture formats, are typically device specific and
highly structured.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Tian Shu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an arm64-specific prctl to allow a thread to reinitialize its
pointer authentication keys to random values. This can be useful when
exec() is not used for starting new processes, to ensure that different
processes still have different keys.
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When pointer authentication is in use, data/instruction pointers have a
number of PAC bits inserted into them. The number and position of these
bits depends on the configured TCR_ELx.TxSZ and whether tagging is
enabled. ARMv8.3 allows tagging to differ for instruction and data
pointers.
For userspace debuggers to unwind the stack and/or to follow pointer
chains, they need to be able to remove the PAC bits before attempting to
use a pointer.
This patch adds a new structure with masks describing the location of
the PAC bits in userspace instruction and data pointers (i.e. those
addressable via TTBR0), which userspace can query via PTRACE_GETREGSET.
By clearing these bits from pointers (and replacing them with the value
of bit 55), userspace can acquire the PAC-less versions.
This new regset is exposed when the kernel is built with (user) pointer
authentication support, and the address authentication feature is
enabled. Otherwise, the regset is hidden.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
[will: Fix to use vabits_user instead of VA_BITS and rename macro]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Changes v2 -> v3:
1. remove check for bpf_dump_raw_ok().
Changes v1 -> v2:
1. Fix error path as Martin suggested.
This patch adds nr_prog_tags and prog_tags to bpf_prog_info. This is a
reliable way for user space to get tags of all sub programs. Before this
patch, user space need to find sub program tags via kallsyms.
This feature will be used in BPF introspection, where user space queries
information about BPF programs via sys_bpf.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull media fixes from Mauro Carvalho Chehab:
- one regression at vsp1 driver
- some last time changes for the upcoming request API logic and for
stateless codec support. As the stateless codec "cedrus" driver is at
staging, don't apply the MPEG controls as part of the main V4L2 API,
as those may not be ready for production yet.
* tag 'media/v4.20-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: Add a Kconfig option for the Request API
media: extended-controls.rst: add note to the MPEG2 state controls
media: mpeg2-ctrls.h: move MPEG2 state controls to non-public header
media: vicodec: set state resolution from raw format
media: vivid: drop v4l2_ctrl_request_complete() from start_streaming
media: vb2: don't unbind/put the object when going to state QUEUED
media: vb2: keep a reference to the request until dqbuf
media: vb2: skip request checks for VIDIOC_PREPARE_BUF
media: vb2: don't call __vb2_queue_cancel if vb2_start_streaming failed
media: cedrus: Fix a NULL vs IS_ERR() check
media: vsp1: Fix LIF buffer thresholds
This time around, seeing some love for some older hw:
- a2xx gpu support for apq8060 (hp touchpad) and imx5 (headless
gpu-only mode)
- a2xx gpummu support (a2xx was pre-iommu)
- mdp4 display support for apq8060/touchpad
For display/dpu:
- a big pile of continuing dpu fixes and cleanups
On the gpu side of things:
- per-submit statistics and traceevents for better profiling
- a6xx crashdump support
- decouple get_iova() and page pinning.. so we can unpin from
physical memory inactive bo's while using softpin to lower
cpu overhead
- new interface to set debug names on GEM BOs and debugfs
output improvements
- additional submit flag to indicate buffers that are used
to dump (so $debugfs/rd cmdstream dumping is useful with
softpin + state-objects)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvVvLPD9_Z4kyfGe98Y--byj6HbxHivEYSgF7Rq7=bFnw@mail.gmail.com
[airlied: make etnaviv build again]
amdgpu:
- DC trace support
- More DC documentation
- XGMI hive reset support
- Rework IH interaction with KFD
- Misc fixes and cleanups
- Powerplay updates for newer polaris variants
- Add cursor plane update fast path
- Enable gpu reset by default on CI parts
- Fix config with KFD/HSA not enabled
amdkfd:
- Limit vram overcommit
- dmabuf support
- Support for doorbell BOs
ttm:
- Support for simultaneous submissions to multiple engines
scheduler:
- Add helpers for hw with preemption support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207233119.16861-1-alexander.deucher@amd.com
This patch introduces a means for syscalls matched in seccomp to notify
some other task that a particular filter has been triggered.
The motivation for this is primarily for use with containers. For example,
if a container does an init_module(), we obviously don't want to load this
untrusted code, which may be compiled for the wrong version of the kernel
anyway. Instead, we could parse the module image, figure out which module
the container is trying to load and load it on the host.
As another example, containers cannot mount() in general since various
filesystems assume a trusted image. However, if an orchestrator knows that
e.g. a particular block device has not been exposed to a container for
writing, it want to allow the container to mount that block device (that
is, handle the mount for it).
This patch adds functionality that is already possible via at least two
other means that I know about, both of which involve ptrace(): first, one
could ptrace attach, and then iterate through syscalls via PTRACE_SYSCALL.
Unfortunately this is slow, so a faster version would be to install a
filter that does SECCOMP_RET_TRACE, which triggers a PTRACE_EVENT_SECCOMP.
Since ptrace allows only one tracer, if the container runtime is that
tracer, users inside the container (or outside) trying to debug it will not
be able to use ptrace, which is annoying. It also means that older
distributions based on Upstart cannot boot inside containers using ptrace,
since upstart itself uses ptrace to monitor services while starting.
The actual implementation of this is fairly small, although getting the
synchronization right was/is slightly complex.
Finally, it's worth noting that the classic seccomp TOCTOU of reading
memory data from the task still applies here, but can be avoided with
careful design of the userspace handler: if the userspace handler reads all
of the task memory that is necessary before applying its security policy,
the tracee's subsequent memory edits will not be read by the tracer.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
