SD specs version 4.x and 5.x have a dedicated slices in the SCR register.
Higher versions will rely on a combination of the existing fields.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The BCM2835 MMC host driver uses a pointer to get from the private
bcm2835_host structure to the generic mmc_host structure. However the
latter is always immediately preceding the former in memory, so compute
its address with a subtraction (which is cheaper than a dereference) and
drop the superfluous pointer.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly
complicated, go with a standard approach instead.
Whilst we're at it, move the comment to the right place.
v2:
- rebased
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce dev_change_proto_down_generic, a generic ndo_change_proto_down
implementation, which sets the netdev carrier state according to proto_down.
This adds the ability to set protodown on vxlan and macvlan devices in a
generic way for use by control protocols like VRRPD.
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A detail for mac_config() had been missed in the documentation for the
method - it is expected that the method will update the MAC to the
settings, rather than completely reprogram the MAC on each call.
Update the documentation for this method for this detail.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Store the request queue the last bio was submitted to in the iocb
private data in addition to the cookie so that we find the right block
device. Also refactor the common direct I/O bio submission code into a
nice little helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Modified to use bio_set_polled().
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For the upcoming async polled IO, we can't sleep allocating requests.
If we do, then we introduce a deadlock where the submitter already
has async polled IO in-flight, but can't wait for them to complete
since polled requests must be active found and reaped.
Utilize the helper in the blockdev DIRECT_IO code.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This new methods is used to explicitly poll for I/O completion for an
iocb. It must be called for any iocb submitted asynchronously (that
is with a non-null ki_complete) which has the IOCB_HIPRI flag set.
The method is assisted by a new ki_cookie field in struct iocb to store
the polling cookie.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A previous change allowed I2C client devices to discover new IRQs upon
reprobe by clearing the IRQ in i2c_device_remove. However, if an IRQ was
assigned in i2c_new_device, that information is lost.
For example, the touchscreen and trackpad devices on a Dell Inspiron laptop
are I2C devices whose IRQs are defined by ACPI extended IRQ types. The
client device structures are initialized during an ACPI walk. After
removing the i2c_hid device, modprobe fails.
This change caches the initial IRQ value in i2c_new_device and then resets
the client device IRQ to the initial value in i2c_device_remove.
Fixes: 6f108dd70d ("i2c: Clear client->irq in i2c_device_remove")
Signed-off-by: Jim Broadus <jbroadus@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
[wsa: this is an easy to backport fix for the regression. We will
refactor the code to handle irq assignments better in general.]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2019-02-21
This series adds some misc updates to mlx5 driver,
1) Eli Britstein, Introduces tunnel entropy control from PCMR register
and fixes GRE key by controlling port tunnel entropy calculation.
2) Eran Ben Elisha, provides some mlx5 fixes to the latest tx devlink health
reporting mechanism.
3) Huy Nguyen, Added the support for ndo bridge_setlink to allow
VEPA/VEB E-Switch legacy mode configurations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Tegra210 timer that runs at oscillator clock
(TMR10-TMR13). We need these timers to work as clock event device and to
replace the ARMv8 architected timer due to it can't survive across the
power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up
source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Pull irqchip updates from Marc Zyngier
- Core pseudo-NMI handling code
- Allow the default irq domain to be retrieved
- A new interrupt controller for the Loongson LS1X platform
- Affinity support for the SiFive PLIC
- Better support for the iMX irqsteer driver
- NUMA aware memory allocations for GICv3
- A handful of other fixes (i8259, GICv3, PLIC)
Flow entropy is calculated on the inner packet headers and used for
flow distribution in processing, routing etc. For GRE-type
encapsulations the entropy value is placed in the eight LSB of the key
field in the GRE header as defined in NVGRE RFC 7637. For UDP based
encapsulations the entropy value is placed in the source port of the
UDP header.
The hardware may support entropy calculation specifically for GRE and
for all tunneling protocols. With commit df2ef3bff1 ("net/mlx5e: Add
GRE protocol offloading") GRE is offloaded, but the hardware is
configured by default to calculate flow entropy so packets transmitted
on the wire have a wrong key. To support UDP based tunnels (i.e VXLAN),
GRE (i.e. no flow entropy) and NVGRE (i.e. with flow entropy) the
hardware behaviour must be controlled by the driver.
Ensure port entropy calculation is enabled for offloaded VXLAN tunnels
and disable port entropy calculation in the presence of offloaded GRE
tunnels by monitoring the presence of entropy enabling tunnels (i.e
VXLAN) and entropy disabing tunnels (i.e GRE).
Fixes: df2ef3bff1 ("net/mlx5e: Add GRE protocol offloading")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit introduced parse_protocol callback which should
extract the protocol number from the L2 header. Make all Ethernet
devices support it.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new optional header_ops callback called parse_protocol and a
wrapper function dev_parse_header_protocol, similar to dev_parse_header.
The new callback's purpose is to extract the protocol number from the L2
header, the format of which is known to the driver, but not to the upper
layers of the stack.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the socket was created with socket(AF_PACKET, SOCK_RAW, 0),
skb->protocol will be unset, __skb_flow_dissect() will fail, and
skb_probe_transport_header() will fall back to the offset_hint, making
the resulting skb_transport_offset incorrect.
If, however, there is no transport header in the packet,
transport_header shouldn't be set to an arbitrary value.
Fix it by leaving the transport offset unset if it couldn't be found, to
be explicit rather than to fill it with some wrong value. It changes the
behavior, but if some code relied on the old behavior, it would be
broken anyway, as the old one is incorrect.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the address range calculation for file-based filters works as
long as the vma that maps the matching part of the object file starts
from offset zero into the file (vm_pgoff==0). Otherwise, the resulting
filter range would be off by vm_pgoff pages. Another related problem is
that in case of a partially matching vma, that is, a vma that matches
part of a filter region, the filter range size wouldn't be adjusted.
Fix the arithmetics around address filter range calculations, taking
into account vma offset, so that the entire calculation is done before
the filter configuration is passed to the PMU drivers instead of having
those drivers do the final bit of arithmetics.
Based on the patch by Adrian Hunter <adrian.hunter.intel.com>.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: 375637bc52 ("perf/core: Introduce address range filtering")
Link: http://lkml.kernel.org/r/20190215115655.63469-3-alexander.shishkin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Re-use the "tps65218_pmic_*_current_limit()" functions of LS3
and calculate the different required bit-shift by counting the
trailing 0s in "struct regulator_desc.csel_mask"
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rhashtable_walk_init function has been obsolete for more than
two years. This patch finally converts its last users over to
rhashtable_walk_enter and removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.
This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).
The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Custom approximation of fractional-divider may not need parent clock
rate checking. For example Rockchip SoCs work fine using grand parent
clock rate even if target rate is greater than parent.
This patch checks parent clock rate only if CLK_SET_RATE_PARENT flag
is set.
For detailed example, clock tree of Rockchip I2S audio hardware.
- Clock rate of CPLL is 1.2GHz, GPLL is 491.52MHz.
- i2s1_div is integer divider can divide N (N is 1~128).
Input clock is CPLL or GPLL. Initial divider value is N = 1.
Ex) PLL = CPLL, N = 10, i2s1_div output rate is
CPLL / 10 = 1.2GHz / 10 = 120MHz
- i2s1_frac is fractional divider can divide input to x/y, x and
y are 16bit integer.
CPLL --> | selector | ---> i2s1_div -+--> | selector | --> I2S1 MCLK
GPLL --> | | ,--------------' | |
`--> i2s1_frac ---> | |
Clock mux system try to choose suitable one from i2s1_div and
i2s1_frac for master clock (MCLK) of I2S1.
Bad scenario as follows:
- Try to set MCLK to 8.192MHz (32kHz audio replay)
Candidate setting is
- i2s1_div: GPLL / 60 = 8.192MHz
i2s1_div candidate is exactly same as target clock rate, so mux
choose this clock source. i2s1_div output rate is changed
491.52MHz -> 8.192MHz
- After that try to set to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div = 8.192MHz
This is because clk_fd_round_rate() thinks target rate
(11.2896MHz) is higher than parent rate (i2s1_div = 8.192MHz)
and returns parent clock rate.
Above is current upstreamed behavior. Clock mux system choose
i2s1_div, but this clock rate is not acceptable for I2S driver, so
users cannot replay audio.
Expected behavior is:
- Try to set master clock to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div * 147/6400 = 11.2896MHz
Change i2s1_div to GPLL / 1 = 491.52MHz at same
time.
If apply this commit, clk_fd_round_rate() calls custom approximate
function of Rockchip even if target rate is higher than parent.
Custom function changes both grand parent (i2s1_div) and parent
(i2s_frac) settings at same time. Clock mux system can choose
i2s1_frac and audio works fine.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@kernel.org: Make function into a macro instead]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.
But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.
Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.
Exclude callers for which network header offset is not known.
Fixes: d5be7f632b ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Embedded Controller has an internal RTC that is exposed
as a standard RTC class driver with read/write functionality.
The driver is added to the drivers/rtc/ so that the maintainer of that
directory will be able to comment on this change, as that maintainer is
the expert on this system. In addition, the driver code is called
indirectly after a corresponding device is registered from core.c,
as opposed to core.c registering the driver callbacks directly.
To test:
> hwclock --show --rtc /dev/rtc1
2007-12-31 16:01:20.460959-08:00
> hwclock --systohc --rtc /dev/rtc1
> hwclock --show --rtc /dev/rtc1
2018-11-29 17:08:00.780793-08:00
> hwclock --show --rtc /dev/rtc1
2007-12-31 16:01:20.460959-08:00
> hwclock --systohc --rtc /dev/rtc1
> hwclock --show --rtc /dev/rtc1
2018-11-29 17:08:00.780793-08:00
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Nick Crews <ncrews@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[Fix the sparse warning: symbol 'wilco_ec_rtc_read/write' was not declared]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add a debugfs attribute that allows sending raw commands to the EC.
This is useful for development and debug but should not be enabled
in a production environment.
To test:
Get the EC firmware build date
First send the request command
> echo 00 f0 38 00 03 00 > raw
Then read the result. "12/21/18" is in the middle of the response
> cat raw
00 31 32 2f 32 31 2f 31 38 00 00 0f 01 00 01 00 .12/21/18.......
Get the EC firmware build date
First send the request command
> echo 00 f0 38 00 03 00 > raw
Then read the result. "12/21/18" is in the middle of the response
> cat raw
00 31 32 2f 32 31 2f 31 38 00 00 0f 01 00 01 00 .12/21/18.......
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Nick Crews <ncrews@chromium.org>
[Fix off-by-one error in wilco_ec/debugfs.c]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This EC is an incompatible variant of the typical Chrome OS embedded
controller. It uses the same low-level communication and a similar
protocol with some significant differences. The EC firmware does
not support the same mailbox commands so it is not registered as a
cros_ec device type. This commit exports the wilco_ec_mailbox()
function so that other modules can use it to communicate with the EC.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Nick Crews <ncrews@chromium.org>
[Fix the sparse warning: symbol 'wilco_ec_transfer' was not declared]
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[Fix Kconfig dependencies for wilco_ec]
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
From
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
To resolve conflicts with net-next and pick up the first patch.
* branch 'mlx5-next':
net/mlx5: Factor out HCA capabilities functions
IB/mlx5: Add support for 50Gbps per lane link modes
net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register
net/mlx5: Add new fields to Port Type and Speed register
net/mlx5: Refactor queries to speed fields in Port Type and Speed register
net/mlx5: E-Switch, Avoid magic numbers when initializing offloads mode
net/mlx5: Relocate vport macros to the vport header file
net/mlx5: E-Switch, Normalize the name of uplink vport number
net/mlx5: Provide an alternative VF upper bound for ECPF
net/mlx5: Add host params change event
net/mlx5: Add query host params command
net/mlx5: Update enable HCA dependency
net/mlx5: Introduce Mellanox SmartNIC and modify page management logic
IB/mlx5: Use unified register/load function for uplink and VF vports
net/mlx5: Use consistent vport num argument type
net/mlx5: Use void pointer as the type in address_of macro
net/mlx5: Align ODP capability function with netdev coding style
mlx5: use RCU lock in mlx5_eq_cq_get()
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Johan writes:
GNSS updates for 5.1-rc1
Here are the GNSS updates for 5.1-rc1, including:
- a new driver for Mediatek-based receivers
- support for SiRF receivers without a wakeup signal
- support for a separate LNA supply for SiRF receivers
Included are also various clean ups and minor fixes.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'gnss-5.1-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss:
gnss: add driver for mediatek receivers
gnss: add mtk receiver type support
dt-bindings: gnss: add mediatek binding
dt-bindings: Add vendor prefix for "GlobalTop Technology, Inc."
dt-bindings: gnss: add lna-supply property
gnss: sirf: add a separate supply for a lna
dt-bindings: gnss: add w2sg0004 compatible string
gnss: sirf: add support for configurations without wakeup signal
gnss: sirf: write data to gnss only when the gnss device is open
gnss: sirf: drop redundant double negation
gnss: sirf: force hibernate mode on probe
gnss: sirf: fix premature wakeup interrupt enable
Commit 36003d4cf5 ("driver core: Fix PM-runtime for links added
during consumer probe") forgot to add a kerneldoc decription for the
new struct device_link member added by it, so do that now.
Fixes: 36003d4cf5 ("driver core: Fix PM-runtime for links added during consumer probe")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are currently 1200+ instances of using platform_get_resource()
and devm_ioremap_resource() together in the kernel tree.
This patch wraps these two calls in a single helper. Thanks to that
we don't have to declare a local variable for struct resource * and can
omit the redundant argument for resource type. We also have one
function call less.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
