Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
This driver has supported passing a LDO enable GPIO for years,
yet this facility has never been put to use in the upstream kernel.
If someone desires to put in place GPIO control for the LDOs,
this can be done by adding a GPIO descriptor table in the MFD
nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
MFD children, or using a board file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When AXP806 support was added, POK was incorrectly expanded to PWROK.
However, the datasheet lists them as POK[LSNP], which is the same as
on the AXP288. Furthermore, the registers associated with POK functions
are the same as the PEK on the other AXP PMICs. This suggests that
"POK" means "Power On Key", much like "PEK" means "Power Enable Key",
instead of "Power OK".
This patch changes the "PWROK" prefix to "POK" for these interrupts.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x driver has lots of mfd_cell and resource structs.
These can all be const-ified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now GPIOD has support for both pdata systems and for non-standard DT
bindings the Arizona reset GPIO can be converted to use it. Worth
noting gpiod_set_raw_value_cansleep is used to match the behaviour
of the old GPIOs. This is because the part is fairly widely used and
it is unknown how many DTs are correctly setting active low through
device tree, so to avoid breaking any existing users it is best to
match the previous behaviour.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit e04653a9dc.
It is no longer needed to install Chrome EC GPE handler to have
GPE enabled in suspend to idle path. It is found that with this
handler installed, EC wake up doesn't work because default EC
event handler that can wake up system is not getting called.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the GPL v2 license boilerplate and update with
the SPDX license identifier.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
changes the probe function of drivers/regulator/tps65218-regulator.c so
that it iterates through all available regulators and assumes that the
regulator IDs are sequential and match the order present in the enum
tps65218_regulator_id. However, for some reason the much older commit
c0ea88b890 ("regulator: tps65218: add support for LS3 current
regulator") updated all arrays with LS3 at the end but added it second
to last for the enum.
Because of this long standing mismatch in order between the
tps65218_regulator_id enum and the regulator_desc array in the tps65218
regulator driver, the new probe function causes the strobe values to be
associated with the wrong regulator ID. This causes LDO1 to fail to
suspend in tps65218_pmic_set_suspend_disable due to not having anything
probes for its strobe value. Fix the order in the enum so the probe
function works as the update intended.
Fixes: 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 5812f0106c ("phy: exynos4: Remove duplicated defines of
PHY register defines") and commit 7a66647b25 ("phy: exynos: Use one
define for enable bit") all users of syscon Exynos PMU headers (for PHY
drivers) are converted to use different headers so these can be removed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable branch between MFD and HWMON due for the v4.18 merge window
Immutable branch between MFD, Input and RTC due for the v4.18 merge window
Immutable branch between MFD and PWM due for the v4.18 merge window
Using input prescaler, capture unit will trigger DMA once every
configurable /2, /4 or /8 events (rising edge). This helps improve
period (only) capture accuracy at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for PMW input mode on pwm-stm32. STM32 timers support
period and duty cycle capture as long as they have at least two PWM
channels. One capture channel is used for period (rising-edge), one
for duty-cycle (falling-edge).
When there's only one channel available, only period can be captured.
Duty-cycle is simply zero'ed in such a case.
Capture requires exclusive access (e.g. no pwm output running at the
same time, to protect common prescaler).
Timer DMA burst mode (from MFD core) is being used, to take two
snapshots of capture registers (upon each period rising edge).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Timers can support up to 7 DMA requests:
- 4 channels, update, compare and trigger.
Optionally request part, or all DMAs from stm32-timers MFD core.
Also add routine to implement burst reads using DMA from timer registers.
This is exported. So, it can be used by child drivers, PWM capture
for instance (but not limited to).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add definitions for the KEEPON_* bits in the "BKUP Mode Cnt" register,
which control the DDR rails to be kept powered when backup mode is
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This version is exists in the Samsung Galaxy Tab 10.1 which is based on the
Nvidia Tegra 2 board. The TPS658624 has the same SM2 voltage table as
TPS658623.
Signed-off-by: ryang <decatf@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
This adds a sysfs attribute (/sys/class/chromeos/cros_ec/kb_wake_angle)
used to set and get the keyboard wake lid angle. This attribute is
present only if 2 accelerometers are controlled by the EC.
This patch also moves the cros_ec features check before the device is
added so the features map obtained from the EC is ready on time.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull RTC updates from Alexandre Belloni:
"This contains a few series that have been in preparation for a while
and that will help systems with RTCs that will fail in 2038, 2069 or
2100.
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct
nvmem_config after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC
time, modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of
letting drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to
use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient
drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support"
* tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (128 commits)
rtc: snvs: Fix usage of snvs_rtc_enable
rtc: mt7622: fix module autoloading for OF platform drivers
rtc: isl12022: use true and false for boolean values
rtc: ab8500: Drop AB8540 support
rtc: remove a warning during scripts/kernel-doc step
rtc: 88pm860x: remove artificial limitation
rtc: 88pm80x: remove artificial limitation
rtc: st-lpc: remove artificial limitation
rtc: mrst: remove artificial limitation
rtc: mv: remove artificial limitation
rtc: hctosys: Ensure system time doesn't overflow time_t
parisc: time: stop validating rtc_time in .read_time
rtc: pcf85063: fix clearing bits in pcf85063_start_clock
rtc: at91sam9: Set name of regmap_config
rtc: s5m: Remove VLA usage
rtc: s5m: Move enum from rtc.h to rtc-s5m.c
rtc: remove VLA usage
rtc: Add useful timestamp definitions
rtc: Add one offset seconds to expand RTC range
rtc: Factor out the RTC range validation into rtc_valid_range()
...
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
Pull libata updates from Tejun Heo:
"Nothing too interesting.
The biggest change is refcnting fix for ata_host - the bug is recent
and can only be triggered on controller hotplug, so very few are
hitting it.
There also are a number of trivial license / error message changes and
some hardware specific changes"
* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
ahci: imx: add the imx8qm ahci sata support
libata: ensure host is free'd on error exit paths
ata: ahci-platform: add reset control support
ahci: imx: fix the build warning
ata: add Amiga Gayle PATA controller driver
ahci: imx: add the imx6qp ahci sata support
ata: change Tegra124 to Tegra
ata: ahci_tegra: Add AHCI support for Tegra210
ata: ahci_tegra: disable DIPM
ata: ahci_tegra: disable devslp for Tegra124
ata: ahci_tegra: initialize regulators from soc struct
ata: ahci_tegra: Update initialization sequence
dt-bindings: Tegra210: add binding documentation
libata: add refcounting to ata_host
pata_bk3710: clarify license version and use SPDX header
pata_falcon: clarify license version and use SPDX header
pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command()
pata_macio: Delete an error message for a failed memory allocation in two functions
pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe()
sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start()
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
- Regarding to imx6q ahci sata, imx6qp ahci sata
has the reset mechanism. Add the imx6qp ahci sata
support in this commit.
- Use the specific reset callback for imx53 sata,
and use the default ahci_ops.softreset for the others.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jonathan writes:
First round of new devices, features and cleanups for IIO in the 4.17 cycle.
Outside of IIO
* Strongly typed 64bit int_sqrt function needed by the mlx90632
New device support
* adc081s
- New driver supporting adc081s, adc101s and adc121s TI ADCs.
* ad5272
- New driver supproting the ad5272 and ad5274 ADI digital potentiometers
with DT bindings.
* axp20x_adc
- support the AXP813 ADC - includes rework patches to prepare for this.
* mlx90632
- New driver with dt bindings for this IR temperature sensor.
Features
* axp20x_adc
- Add DT bindings and probing.
* dht11
- The sensor has a wider range than advertised in the datasheet - support it.
* st_lsm6dsx
- Add hardware timestamp su9pport.
Cleanups
* ABI docs
- Update email contact for Matt Ranostay
* SPDX changes
- Matt Ranostay has moved his drivers over to SPDX. Currently we are making
this an author choice in IIO.
* ad7192
- Disable burnout current on misconfiguration. No actually effect as
they simply won't work otherwise.
* ad7476
- Drop a license definition that was replicating information in SPDX tag.
* ade7758
- Expand buf_lock to cover both buffer and state protection allowing
unintented uses of mlock in the core to be removed.
* ade7759
- Align parameters to opening parenthesis.
* at91_adc
- Depend on sysfs instead of selecting it - for try wide consistency.
* ccs811
- trivial naming type for a define.
* ep93xx
- Drop a redundant return as a result checking platform_get_resource.
* hts221
- Regmap conversion which simplifies the driver somewhat.
- Clean up some restricted endian cast warnings.
- Drop a trailing whitespace from a comment
- Drop an unnecessary get_unaligned by changing to the right 16bit data type.
* ms5611
- Fix coding style in the probe function (whitespace)
* st_accel
- Use strlcpy instead of strncpy to avoid potentially truncating a string.
When setting up a fixed regulator on the DA9055, pass a descriptor
instead of a global GPIO number. This facility is not used in the
kernel so we can easily just say that this should be a descriptor
if/when put to use.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull RTC updates from Alexandre Belloni:
"Not much this cycle. I've pushed the at32ap700x removal late but it is
unlikely to cause any issues.
Summary:
Subsystem:
- Move ABI documentation to Documentation/ABI
New driver:
- NXP i.MX53 SRTC
- Chrome OS EC RTC
Drivers:
- Remove at32ap700x
- Many fixes in various error paths"
* tag 'rtc-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: remove rtc-at32ap700x
Documentation: rtc: move iotcl interface documentation to ABI
Documentation: rtc: add sysfs file permissions
Documentation: rtc: move sysfs documentation to ABI
rtc: mxc_v2: remove __exit annotation
rtc: mxc_v2: Remove unnecessary platform_get_resource() error check
rtc: add mxc driver for i.MX53 SRTC
dt-bindings: rtc: add bindings for i.MX53 SRTC
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_set_time
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_read_time
rtc: omap: fix unbalanced clk_prepare_enable/clk_disable_unprepare
rtc: ac100: Fix multiple race conditions
rtc: sun6i: ensure rtc is kfree'd on error
rtc: cros-ec: add cros-ec-rtc driver.
mfd: cros_ec: Introduce RTC commands and events definitions.
rtc: stm32: Fix copyright
rtc: Remove unused RTC_DEVICE_NAME_SIZE
rtc: r9701: Remove r9701_remove function
rtc: brcmstb-waketimer: fix error handling in brcmstb_waketmr_probe()
The X-Powers AXP813 PMIC is really close to what is already done for
AXP20X/AXP22X.
There are two pairs of bits to set the rate (one for Voltage and Current
measurements and one for TS/GPIO0 voltage measurements) instead of one.
The register to set the ADC rates is different from the one for
AXP20X/AXP22X.
GPIO0 can be used as an ADC (measuring Volts) unlike for AXP22X.
The scales to apply to the different inputs are unlike the ones from
AXP20X and AXP22X.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The powerhold mask for TPS65917 is different when comapred to
the other palmas versions. Hence assign the right mask that enables
power off of tps65917 pmic correctly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver for RAVE Supervisory Processor, an MCU implementing
various bits of housekeeping functionality (watchdoging, backlight
control, LED control, etc) on RAVE family of products by Zodiac
Inflight Innovations.
This driver implementes core MFD/serdev device as well as
communication subroutines necessary for commanding the device.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros_ec_dev module is responsible for registering the MFD devices
attached to the ChromeOS EC. This patch moves this module to drivers/mfd
so calls to mfd_add_devices() are not done from outside the MFD subtree
anymore.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power
saving") adds powersaving support for device-ids 5249 524a and 525a.
But as a side effect it breaks ASPM support for all the other device-ids,
causing e.g. the Haswell CPU on a Lenovo T440s to not go into a higher
c-state then PC3, while previously it would go to PC7, causing the
machine to idle at 7.4W instead of 6.6W!
The problem here is the new option.dev_aspm_mode field, which only gets
explicitly initialized in the new code for the device-ids 5249 524a and
525a. Leaving the dev_aspm_mode 0 for the other device-ids.
The default dev_aspm_mode 0 is mapped to DEV_ASPM_DISABLE, but the
old behavior of calling rtsx_pci_enable_aspm() when idle and
rtsx_pci_disable_aspm() when busy happens when dev_aspm_mode ==
DEV_ASPM_DYNAMIC.
This commit changes the enum so that 0 = DEV_ASPM_DYNAMIC matching the
old default behavior, fixing the pm regression with the other device-ids.
Fixes: 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power saving")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull sound updates from Takashi Iwai:
"There are no big surprising changes in this cycle, yet not too boring,
either. The biggest change from diffstat POV is the removal of the
legacy OSS driver codes that have been already disabled for a long
time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the
malicious device accesses with a new helper code for endpoint
sanity check
- Lots of cleanups for ASoC Intel platform code, including support
for their open source audio firmware
- Continued ASoC core componentization works
- Support for scaling MCLK with sample rate in ASoC simple-card
- Stabler PCM hot-unplug capability, especially for ASoC usages"
* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
Documentation: sound: hd-audio: notes.rst
ASoC: bcm2835: Support left/right justified and DSP modes
ASoC: bcm2835: Enforce full symmetry
ASoC: bcm2835: Support additional samplerates up to 384kHz
ASoC: bcm2835: Add support for TDM modes
ASoC: add mclk-fs support to audio graph card
ASoC: add mclk-fs to audio graph card binding
ASoC: rt5514: work around link error
ASoC: rt5514: mark PM functions as __maybe_unused
ASoC: rt5663: Check the JD status in the button pushing
ASoC: amd: Modified DMA transfer Mechanism for Playback
ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
ASoC: da7213: add support for DSP modes
ASoC: sun8i-codec: Add a comment on the LRCK inversion
ASoC: sun8i-codec: Set the BCLK divider
ASoC: rt5663: Delay and retry reading rt5663 ID register
ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
ASoC: cs42l56: Fix reset GPIO name in example DT binding
ASoC: rt5514-spi: check irq status to schedule data copy in resume function
...
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...