Move mt76x02_get_txpower utility routine in mt76x02-lib module
in order to be reused by mt76x0 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_sw_scan and mt76x02_sw_scan_complete utility routines
in mt76x02_util.c in order to be reused by mt76x0 and mt76x2u drivers
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable/disable pre_tbtt_tasklet in mt76x0 driver in order
to add AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx beacon utility routines in mt76x02_mmio.c
in order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_beacon mac routines in mt76x02_mac.c in
order to be reused by mt76x0 driver adding AP support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_init_device routine in mt76x02_util.c in order to be
reused by mt76x0 driver and remove duplicated code. Move interface
combo definition supported by the driver in mt76x02_init_device routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_set_short_preamble routine in mt76x02-lib module
since it is shared between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify firmware version used on mt76x0e and mt76x0u drivers.
Fallback to mt7610u fw if mt7610e one is not available
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove no longer used mt76x0_mac_set_ampdu_factor routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing firmware declaration for mt76x0e driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt76x0_init_mac_registers routine using mt76_set, mt76_clear
and mt76_rmw utility routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update mt76x0_phy_ant_select() to conform vendor driver, most notably
add dual antenna mode support, read configuration from EEPROM and
move ant select out of channel config to init phase. Plus small MT7630E
quirk for MT_CMB_CTRL register which vendor driver dedicated to this
chip do.
This make MT7630E workable with mt76x0e driver and do not cause any
problems on MT7610U for me.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add submit_urb and rx_urb static tracepoints in mt76-usb module.
Move trace_mac_txstat_fetch in mt76x02_mac_load_tx_status routine
in order to be available to usb drivers. Moreover remove
no longer used mt76x0/trace.{c,h}
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some RF registers need different values for various chips.
For at least mt76x0_rf_central_tab registers, overwriting them later does
not work, as the wrong values can cause the entire system to hang on some
devices with MT7610E
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make previously exported functions static where possible
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Driver works better for MT7630 without MCU calibration, which
looks like it can hangs the firmware. Vendor driver do not
perform it for MT7630 as well.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Align phy calibration logic between mt76x0u and mt76x0e drivers
This patch improves connection stability with low SNR
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mac workqueue support to mt76x2u driver in order
to compute device statistics and add mac stuck routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_mac_work utility routine as stats workqueue handler
and remove duplicated code. Moreover run mac stuck check in
mt76x02_mac_work for client interfaces.
Remove no longer used avg_ampdu_len and mt76x02_mac_stats data
structure in mt76x02_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02 debugfs implementation and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_debugfs in mt76x02-lib module in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_work routine in mt76x02_mac.c in order to be reused by
mt76x0 driver to read device statistics
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_update_channel routine in mt76x02-lib module in
order to be reused by mt76x0 driver adding get_survey support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve initvals_phy.h code readability (there are no actual changes
of original values)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify mt76x0_phy_vco_cal and mt76x0_phy_set_chan_rf_params
routines using mt76x0_rf_wr, mt76x0_rf_set and mt76x0_rf_clear
helper routines. Moreover over get rid of magic numbers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x0_phy as prefix for routines in mt76x0/phy.c
Moreover use mt76x0_rf_set to enable vco calibration in
mt76x0_phy_vco_cal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify firmware version used on mt76x2e and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When CONFIG_LEDS_CLASS is disabled, or it is a loadable module while
mt76 is built-in, we run into a link error:
drivers/net/wireless/mediatek/mt76/mac80211.o: In function `mt76_register_device':
mac80211.c:(.text+0xb78): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_of_led_classdev_register'
We don't really need a hard dependency here as the driver can presumably
work just fine without LEDs, so this follows the iwlwifi example and
adds a separate Kconfig option for the LED support, this will be available
whenever it will link, and otherwise the respective code gets left out from
the driver object.
Fixes: 17f1de56df ("mt76: add common code shared between multiple chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not perform phy/vga calibration during channel switch.
Moreover remove mt76x0_agc_save and mt76x0_agc_restore routines
since they are no longer necessary. Furthermore run mt76_set_channel
in order to check if there are pending frames during channel switch
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_init_agc_gain routine in mt76x02-lib moudule in
order to be reused by mt76x0 for vga initalization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_adjust_vga_gain routine in mt76x02-lib module
in order to be reused by mt76x0 driver for vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_get_rssi_gain_thresh and mt76x2_get_low_rssi_gain_thresh
routines in mt76x02-lib module in order to be reused by mt76x0 driver
for dynamic vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce phy/vco temperature calibration.
Moreover fix configuration of register 67 on bank0
during temperature reading and use mt76_poll utility routine
to poll core34 register.
Furthermore temperature compensation needs to be disabled
if the device supports tssi compensation.
This issue has never been hit since temperature reading is not
actually used by usb code.
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_tssi_enabled in order to check if tssi compensation
is enabled since mt76x0 condition differs from mt76x2 one.
Moreover move back mt76x02_temp_tx_alc_enabled and mt76x02_tssi_enabled
routines in mt76x2/eeprom.h since they are mt76x2 specific
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not run mt76x0_vco_cal and mt76x0_bbp_set_bw routines and
configure MT_TX_SW_CFG0 register for pcie devices in
mt76x0_phy_set_channel function.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_phy_calirate routine in order to perform
phy calibration for mt76x0e devices.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename mt76x0_phy_calibrate routine in mt76x0_phy_calibration_work
in order to not collide with calibration routine for mt76x0e
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_set_band routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_set_bw routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix restore value configured in MT_BBP(IBI, 9) register in
mt76x0_phy_recalibrate_after_assoc routine.
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Use the register number define instead of a magic value
- Fix inverted bit test (override needs to be applied if the bit is not set)
Fixes: 2b2cb40bcd ("mt76x0: pci: add hw initialization at bootstrap")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c: In function 'mt76x0e_register_device':
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c:107:8: warning:
variable 'data' set but not used [-Wunused-but-set-variable]
It seems correct value to write is 'data'
Fixes: 2b2cb40bcd ("mt76x0: pci: add hw initialization at bootstrap")
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reserve enough room for USB skb, so we don not need to check
the room every time we send frame.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x0_register_device routine in mt76x0e_register_device
in order to register the device to the mac80211 layer.
Moreover init mt76_driver_ops data structure and register
interrupt line
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
