This adds the basic M10V SoC support under arch/arm.
Since all cores are activated in the custom bootloader before booting
linux, it is necessary to wait for the secondary-cores using cpu-enable-
method and special sram.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The maximum voltage value for buck8 regulator on Odroid XU3/XU4 boards is
set too low. Increase it to the 2000mV as specified on the board schematic.
So far the board worked fine, because of the bug in the PMIC driver, which
used incorrect step value for that regulator. It interpreted the voltage
value set by the bootloader as 1225mV and kept it unchanged. The regulator
driver has been however fixed recently in the commit 56b5d4ea77
("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35"), what results
in reading the proper buck8 value and forcing it to 1500mV on boot. This
is not enough for proper board operation and results in eMMC errors during
heavy IO traffic. Increasing maximum voltage value for buck8 restores
original driver behavior and fixes eMMC issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 86a2d2ac5e ("ARM: dts: Add dts file for Odroid XU3 board")
Fixes: 56b5d4ea77 ("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This disables the old FBDEV driver and enables the PL111
DRM driver on the SPEAr3xx.
There are some device trees in the kernel that switches
the DT node for the PL110 to "okay" but none of these
have any display defined, so we can safely switch to this
driver before we get any users starting to define
displays. Let them do it on top of the new driver
infrastructure instead.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This updates the NHK8815 defconfig to reflect the recent
structural changes in Kconfigs all over the kernel:
- PREEMPT option was moved around
- MODULES options were moved around
- MTD_NAND options were moved around
- INPUT_MOUSEDEV doesn't have to be explicitly unselected
anymore (not on by default)
- DEBUG_GPIO should really not be in any default config
- MMC_BLOCK_BOUNCE is gone from Kconfig
- CRYPTO options were moved around
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The CONFIG_SND_PXA2XX_AC97 driver is for the old AC97 bus implementation,
and conflicts with all the new-style AC97 drivers after the conversion,
so the drivers we want all get turned off.
Not disabling the symbol however does the right thing, and we get
the drivers that are selectively enabled here.
Fixes: 25540f68c8 ("ASoC: pxa: change ac97 dependencies")
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull crypto fixes from Herbert Xu:
"This fixes a compiler warning introduced by a previous fix, as well as
two crash bugs on ARM"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha512/arm - fix crash bug in Thumb2 build
crypto: sha256/arm - fix crash bug in Thumb2 build
crypto: ccree - add missing inline qualifier
Pull additional syscall ABI cleanup for y2038 from Arnd Bergmann:
This is a follow-up to the y2038 syscall patches already merged in the tip
tree. As the final 32-bit RISC-V syscall ABI is still being decided on,
this is the last chance to make a few corrections to leave out interfaces
based on 32-bit time_t along with the old off_t and rlimit types.
The series achieves this in a few steps:
- A couple of bug fixes for minor regressions I introduced
in the original series
- A couple of older patches from Yury Norov that I had never
merged in the past, these fix up the openat/open_by_handle_at and
getrlimit/setrlimit syscalls to disallow the old versions of off_t
and rlimit.
- Hiding the deprecated system calls behind an #ifdef in
include/uapi/asm-generic/unistd.h
- Change arch/riscv to drop all these ABIs.
Originally, the plan was to also leave these out on C-Sky, but that now
has a glibc port that uses the older interfaces, so we need to leave
them in place.
To access PRBARn, where n is referenced as a binary number:
MRC p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0] ; Read PRBARn into Rt
MCR p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0] ; Write Rt into PRBARn
To access PRLARn, where n is referenced as a binary number:
MRC p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0]+1 ; Read PRLARn into Rt
MCR p15, 0, <Rt>, c6, c8+n[3:1], 4*n[0]+1 ; Write Rt into PRLARn
For PR{B,L}AR4, n is 4, n[0] is 0, n[3:1] is 2, while current encoding
done with n[0] set to 1 which is wrong. Use proper encoding instead.
Fixes: 046835b4aa ("ARM: 8757/1: NOMMU: Support PMSAv8 MPU")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
arm64 has got relaxation on GIC version check at early boot stage due
to update of the GIC architecture let's align ARM with that.
To help backports (even though the code was correct at the time of writing)
Fixes: e59941b9b3 ("ARM: 8527/1: virt: enable GICv3 system registers")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
MCPM does a soft reset of the CPUs and uses common cpu_resume() routine to
perform low-level platform initialization. This results in a try to install
HYP stubs for the second time for each CPU and results in false HYP/SVC
mode mismatch detection. The HYP stubs are already installed at the
beginning of the kernel initialization on the boot CPU (head.S) or in the
secondary_startup() for other CPUs. To fix this issue MCPM code should use
a cpu_resume() routine without HYP stubs installation.
This change fixes HYP/SVC mode mismatch on Samsung Exynos5422-based Odroid
XU3/XU4/HC1 boards.
Fixes: 3721924c81 ("ARM: 8081/1: MCPM: provide infrastructure to allow for MCPM loopback")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use unified assembler syntax (UAL) in inline assembler. Divided
syntax is considered deprecated. This will also allow to build
the kernel using LLVM's integrated assembler.
When compiling non-Thumb2 GCC always emits a ".syntax divided"
at the beginning of the inline assembly which makes the
assembler fail. Since GCC 5 there is the -masm-syntax-unified
GCC option which make GCC assume unified syntax asm and hence
emits ".syntax unified" even in ARM mode. However, the option
is broken since GCC version 6 (see GCC PR88648 [1]). Work
around by adding ".syntax unified" as part of the inline
assembly.
[0] https://gcc.gnu.org/onlinedocs/gcc/ARM-Options.html#index-masm-syntax-unified
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=88648
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use unified assembler syntax (UAL) in assembly files. Divided
syntax is considered deprecated. This will also allow to build
the kernel using LLVM's integrated assembler.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use unified assembler syntax (UAL) in headers. Divided syntax is
considered deprecated. This will also allow to build the kernel
using LLVM's integrated assembler.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use unified assembler syntax (UAL) in macros. Divided syntax is
considered deprecated. This will also allow to build the kernel
using LLVM's integrated assembler.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Mostly unwind is done with irqs enabled however SLUB may call it with
irqs disabled while creating a new SLUB cache.
I had system freeze while loading a module which called
kmem_cache_create() on init. That means SLUB's __slab_alloc() disabled
interrupts and then
->new_slab_objects()
->new_slab()
->setup_object()
->setup_object_debug()
->init_tracking()
->set_track()
->save_stack_trace()
->save_stack_trace_tsk()
->walk_stackframe()
->unwind_frame()
->unwind_find_idx()
=>spin_lock_irqsave(&unwind_lock);
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When running kprobe on -rt kernel, the below bug is caught:
|BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:931
|in_atomic(): 1, irqs_disabled(): 128, pid: 14, name: migration/0
|Preemption disabled at:[<802f2b98>] cpu_stopper_thread+0xc0/0x140
|CPU: 0 PID: 14 Comm: migration/0 Tainted: G O 4.8.3-rt2 #1
|Hardware name: Freescale LS1021A
|[<8025a43c>] (___might_sleep)
|[<80b5b324>] (rt_spin_lock)
|[<80b5c31c>] (__patch_text_real)
|[<80b5c3ac>] (patch_text_stop_machine)
|[<802f2920>] (multi_cpu_stop)
Since patch_text_stop_machine() is called in stop_machine() which
disables IRQ, sleepable lock should be not used in this atomic context,
so replace patch_lock to raw lock.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
commit 137cd7100e
"ARM: dts: Enable Gemini flash access" contained a bug
by disabling the display controller, while the whole
idea with the patch was to enable flash access AND
the display controller, simultaneously. Fix it up.
Fixes: 137cd7100e ("ARM: dts: Enable Gemini flash access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
One change to deprecate old CPSW Ethernet PHY mode selection driver
With the device tree changes configuring CPSW with a proper PHY driver,
we want to deprecate the old driver to avoid new users for it.
Note that this driver is based on the related dts changes.
* tag 'omap-for-v5.1/cpsw-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
net: ethernet: ti: cpsw: deprecate cpsw-phy-sel driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This switches the ARM Integrator to use the new PL11x DRM
driver. We need CMA enabled to get coherent allocations
at all times. The dumb VGA DAC bridge is needed for
the VGA output on the reference designs, and backlight
is needed when using an external display.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
KVM/arm updates for Linux v5.1
- A number of pre-nested code rework
- Direct physical timer assignment on VHE systems
- kvm_call_hyp type safety enforcement
- Set/Way cache sanitisation for 32bit guests
- Build system cleanups
- A bunch of janitorial fixes
mvebu fixes for 5.0 (part 2)
Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release
* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Device tree changes to make CPSW Ethernet use proper phy driver
We now have a proper PHY driver with drivers/phy/ti/phy-gmii-sel.c to
configure the CPSW PHY. These changes update all CPSW users to use the
new driver that already got merged during v5.0 merge window.
* tag 'omap-for-v5.1/dt-cpsw-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Two am335x ethernet phy mode fixes for v5.0-rc cycle
Recent changes with commit cd28d1d6e5: ("net: phy: at803x: Disable phy
delay for RGMII mode") broke Ethernet on am335x-evmsk, and turns out some
device driver fixes are needed.
Even without the driver fixes, am335x needs to run in rgmii-id mode instead
rgmii-txid mode. Things have been working based on luck as the broken driver
has been configuring rgmii-id mode. Let's fix that as that way things work
as they're supposed to work from hardware wiring point of view.
* tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make the arm ctr-aes-ce algorithm update the IV buffer to contain the
next counter after processing a partial final block, rather than leave
it as the last counter. This makes ctr-aes-ce pass the updated AES-CTR
tests. This change also makes the code match the arm64 version in
arch/arm64/crypto/aes-modes.S more closely.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SHA512 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SHA256 code we adopted from the OpenSSL project uses a rather
peculiar way to take the address of the round constant table: it
takes the address of the sha256_block_data_order() routine, and
substracts a constant known quantity to arrive at the base of the
table, which is emitted by the same assembler code right before
the routine's entry point.
However, recent versions of binutils have helpfully changed the
behavior of references emitted via an ADR instruction when running
in Thumb2 mode: it now takes the Thumb execution mode bit into
account, which is bit 0 af the address. This means the produced
table address also has bit 0 set, and so we end up with an address
value pointing 1 byte past the start of the table, which results
in crashes such as
Unable to handle kernel paging request at virtual address bf825000
pgd = 42f44b11
[bf825000] *pgd=80000040206003, *pmd=5f1bd003, *pte=00000000
Internal error: Oops: 207 [#1] PREEMPT SMP THUMB2
Modules linked in: sha256_arm(+) sha1_arm_ce sha1_arm ...
CPU: 7 PID: 396 Comm: cryptomgr_test Not tainted 5.0.0-rc6+ #144
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
PC is at sha256_block_data_order+0xaaa/0xb30 [sha256_arm]
LR is at __this_module+0x17fd/0xffffe800 [sha256_arm]
pc : [<bf820bca>] lr : [<bf824ffd>] psr: 800b0033
sp : ebc8bbe8 ip : faaabe1c fp : 2fdd3433
r10: 4c5f1692 r9 : e43037df r8 : b04b0a5a
r7 : c369d722 r6 : 39c3693e r5 : 7a013189 r4 : 1580d26b
r3 : 8762a9b0 r2 : eea9c2cd r1 : 3e9ab536 r0 : 1dea4ae7
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment user
Control: 70c5383d Table: 6b8467c0 DAC: dbadc0de
Process cryptomgr_test (pid: 396, stack limit = 0x69e1fe23)
Stack: (0xebc8bbe8 to 0xebc8c000)
...
unwind: Unknown symbol address bf820bca
unwind: Index not found bf820bca
Code: 441a ea80 40f9 440a (f85e) 3b04
---[ end trace e560cce92700ef8a ]---
Given that this affects older kernels as well, in case they are built
with a recent toolchain, apply a minimal backportable fix, which is
to emit another non-code label at the start of the routine, and
reference that instead. (This is similar to the current upstream state
of this file in OpenSSL)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Switch to use phy-gmii-sel PHY instead of cpsw-phy-sel.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use phy-gmii-sel PHY instead of cpsw-phy-sel.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use phy-gmii-sel PHY instead of cpsw-phy-sel.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use phy-gmii-sel PHY instead of cpsw-phy-sel.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DaVinci SoC updates for v5.1 (part 3)
-------------------------------------
This pull request gets rid of mach-davinci private interrupt controller
implmentations (aintc and cp_initc) and moves them to drivers/irqchip.
mach/irqs.h usage outside of mach-davinci has been rid of.
The driver changes (input and irqchip) have been acked by respective
maintainers.
* tag 'davinci-for-v5.1/soc-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci: (57 commits)
ARM: davinci: remove intc related fields from davinci_soc_info
irqchip: davinci-cp-intc: move the driver to drivers/irqchip
ARM: davinci: cp-intc: remove redundant comments
ARM: davinci: cp-intc: drop GPL license boilerplate
ARM: davinci: cp-intc: use readl/writel_relaxed()
ARM: davinci: cp-intc: unify error handling
ARM: davinci: cp-intc: improve coding style
ARM: davinci: cp-intc: request the memory region before remapping it
ARM: davinci: cp-intc: use the new-style config structure
ARM: davinci: cp-intc: convert all hex numbers to lowercase
ARM: davinci: cp-intc: use a common prefix for all symbols
ARM: davinci: cp-intc: add the new config structures for da8xx SoCs
irqchip: davinci-cp-intc: add a new config structure
ARM: davinci: cp-intc: add a wrapper around cp_intc_init()
ARM: davinci: cp-intc: remove cp_intc.h
irqchip: davinci-aintc: move the driver to drivers/irqchip
ARM: davinci: aintc: remove unnecessary includes
ARM: davinci: aintc: remove the timer-specific irq_set_handler()
ARM: davinci: aintc: request memory region before remapping it
ARM: davinci: aintc: unify error handling
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Samsung DTS ARM changes for v5.1, part 2
1. Enable ADC on Odroid HC1 board.
2. Fix clkout register failure on Exynos3250.
3. Allow using earlycon on Arndale board.
4. Disable ARM PMU on Odroid XU3 Lite because it is locked by Trusted
Firmware.
5. Add support for secondary DAI to Odroid XU3 and XU4 boards.
* tag 'samsung-dt-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 482997699e ("ARM: tegra: Fix unit_address_vs_reg DTC warnings
for /memory") inadventently broke device tree ABI by adding a unit-
address to the "/memory" node because the device tree compiler flagged
the missing unit-address as a warning.
Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the
full name of the memory node in device tree being exactly "/memory". It
can be argued whether this was a good decision or not, and some other
bootloaders (such as U-Boot) do accept a unit-address in the name of the
node, but the device tree is an ABI and we can't break existing setups
just because the device tree compiler considers it bad practice to omit
the unit-address nowadays.
This partially reverts the offending commit and restores device tree ABI
compatibility.
Fixes: 482997699e ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory")
Reported-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is primarily used through DT entries, but two architectures
and two drivers call it directly. So instead of selecting the config
symbol for random architectures pull it in implicitly for the actual
users. Also rename the Kconfig option to describe the feature better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
marvell,dsa properties has been removed from kirkwood-rd88f6281.dtsi
while cleanuping the dsa binding, but the dsa reference in
kirkwood-rd88f6281-z0.dts has been missed causing the following errors:
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:21.4-16: Warning (reg_format): /dsa/switch@0:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:23.5-15: Warning (reg_format): /dsa/switch@0/port@4:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:20.12-26.5: Warning (avoid_default_addr_size): /dsa/switch@0: Relying on default #address-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:20.12-26.5: Warning (avoid_default_addr_size): /dsa/switch@0: Relying on default #size-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:22.11-25.6: Warning (avoid_default_addr_size): /dsa/switch@0/port@4: Relying on default #address-cells value
arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts:22.11-25.6: Warning (avoid_default_addr_size): /dsa/switch@0/port@4: Relying on default #size-cells value
So remove the dsa reference too in order to fix this issue.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The header search path -I. in kernel Makefiles is very suspicious;
it allows the compiler to search for headers in the top of $(srctree),
where obviously no header file exists.
I was able to build without these extra header search paths.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Move this little function to the header files for arm/arm64 so other
code can make use of it directly.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VHE systems don't have to emulate the physical timer, we can simply
assign the EL1 physical timer directly to the VM as the host always
uses the EL2 timers.
In order to minimize the amount of cruft, AArch32 gets definitions for
the physical timer too, but is should be generally unused on this
architecture.
Co-written with Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
