Access point require this API to check peer alive status.
Assume peer is alive when it is connected, because
firmware implements keep alive checks and will disconnect
peer if it is not alive.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.
The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.
The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the foreign page flag in netback to get the domid and grant ref
needed for the grant copy. This signficiantly simplifies the netback
code and makes netback work with foreign pages from other backends
(e.g., blkback).
This allows blkback to use iSCSI disks provided by domUs running on
the same host.
Signed-off-by: Jennifer Herbert <jennifer.herbert@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add gnttab_alloc_pages() and gnttab_free_pages() to allocate/free pages
suitable to for granted maps.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Ballooned pages are always used for grant maps which means the
original frame does not need to be saved in page->index nor restored
after the grant unmap.
This allows the workaround in netback for the conflicting use of the
(unionized) page->index and page->pfmemalloc to be removed.
Signed-off-by: Jennifer Herbert <jennifer.herbert@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add a common function that pushes the skb in the network queue with adding
timestamps information, converted from time values read from the
PEAK USB adapters.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for the following new PEAK-System technik CANFD USB adapters:
PCAN-USB FD single CANFD channel USB adapter
PCAN-USB Pro FD dual CANFD channels USB adapter
The communication protocol has been developed using some mechanisms that
did exist in the PCAN-USB Pro, thus, this patch also changes some
previously static functions and data into global ones.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
includes changes that deal with the new struct canfd_frame.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
does the mandatory changes to support new data bittiming specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add the definition of a new callback that enable any PEAK-System CAN USB
adapter to grant read access to its Bus Error Counters value. This ability is
not supported by all the PEAK-System adapters, thus, for those, the callback
pointer will be initiaized to NULL, which is correct regarding the linux-can
device driver specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Export the ctrlmode_supported value from the core file to each adapter specific
file. This has been mandatory for supporting the new CANFD extension.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A "struct peak_usb_adapter" describes a certain USB adapter, as this doesn't
change during runtime, this patch marks all USB adapter definitions as const.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the list "static struct peak_usb_adapter
*peak_usb_adapters_list[]" to be used with ARRAY_SIZE not with a NULL
termination, as the size is known during compile time.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'USBcanII'. From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.
This patch adds support for the USBcanII family of devices to the
current Kvaser Leaf-only driver.
CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.
List of new devices supported by this driver update:
- Kvaser USBcan II HS/HS
- Kvaser USBcan II HS/LS
- Kvaser USBcan Rugged ("USBcan Rev B")
- Kvaser Memorator HS/HS
- Kvaser Memorator HS/LS
- Scania VCI2 (if you have the Kvaser logo on top)
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update all of the can interface's state and error counters before
trying any skb allocation that can actually fail with -ENOMEM.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In Intel Quark SoC X1000, both of the Ethernet controllers support
MSI interrupt handling. This patch enables them to use MSI interrupt
servicing in stmmac_pci for Intel Quark X1000.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces run-time board detection through DMI and MAC-PHY
configuration function used by quark_default_data() during initialization. It
fills up the phy_addr for Galileo and Galileo Gen2 boards to indicate that the
Ethernet MAC controller is or is not connected to any PHY.
The implementation takes into consideration for future expansion in Quark
series boards that may have different PHY address that is linked to its MAC
controllers.
This piece of work is derived from Bryan O'Donoghue's initial work for Quark
X1000 enabling.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel Quark SoC X1000 provides two 10/100 Mbps Ethernet MAC
controllers which may or may not be connected to PHY on board.
This MAC controller only supports RMII PHY. This patch add Quark
PCI ID as well as Quark default platform data info to this driver.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently CPTS is built into the netcp driver even though there is no
call out to the CPTS driver. This patch removes the dependency in Kconfig
and remove cpts.o from the Makefile for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move firmware version MACRO to a new t4fw_version.h file so that csiostor driver
can also use it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware might change the hca core clock frequency after the driver
issues the INIT_PORT command. Therefore we need to query the new
value again and save in to the cached dev caps.
Fixes: ddd8a6c1 ('net/mlx4_core: Read HCA frequency and map internal clock')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are dumping device capabilities which are supported both by the
firmware and the driver. Align the array that holds the capability
strings with this practice.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory corruption at mlx4_MAD_IFC_wrapper.
A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).
Fixes: 0a9a018 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback.
When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise,
set according to ethtool->speed.
Usage:
- ethtool -s eth<x> speed 56000 autoneg off
- ethtool -s eth<x> advertise 0x800000 autoneg on
While we're here:
- Move proto_admin masking outcome check to be adjacent to the operation.
- Move en_warn("port reset..") print to "port reset" block.
Fixes: 312df74 ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.
Reported by the Mellanox Beijing team.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.
This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.
This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).
However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).
Reported-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.
The reserved L_key value for a VF is:
VF_lkey = base_lkey + (VF_number << 8).
This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.
To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.
When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).
These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).
Note also that vxlan_nlmsg_size() was not updated.
Fixes: 193523bf93 ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warning about non-static function
drivers/net/bonding/bond_main.c:3737:5: warning: symbol
'bond_3ad_xor_xmit' was not declared. Should it be static?
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to fix the following problems when an actor or
partner's aggregator is not active:
1. a slave's lacp port state is marked as AD_STATE_SYNCHRONIZATION
even if it is attached to an inactive aggregator. LACP advertises
this state to the partner, making the partner think he can move
into COLLECTING_DISTRIBUTING state even though this link will not
pass traffic on the local side
2. a slave goes into COLLECTING_DISTRIBUTING state without checking
if the aggregator is actually active
3. when in COLLECTING_DISTRIBUTING state, the partner parameters may
change, e.g. the partner_oper_port_state.SYNCHRONIZATION. The
local mux machine is not reacting to the change and continue to
keep the slave and bond up
4. When bond slave leaves an inactive aggregator and joins an active
aggregator, the actor oper port state need to update to SYNC state.
v2:
* fix style issues in bond_3ad.c
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mode 802.3ad, fix incorrect bond slave active state when slave is not in
active aggregator. During bond_open(), the bonding driver always sets
the slave active flag to true if the bond is not in active-backup, alb,
or tlb modes. Bonding should let the aggregator selection logic set the
active flag when in 802.3ad mode.
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
return type of wait_for_completion_timeout is unsigned long not int, this
patch just fixes up the declarations.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
