Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'
Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The spinlock module's SYSCONFIG register does not support
smart wakeup, so remove this flag from the idle modes in
the spinlock hwmod definition.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just like IS_PM34XX_ERRATUM, IS_PM44XX_ERRATUM is valid only if
CONFIG_PM is enabled, else, disabling CONFIG_PM results in build
failure complaining about the following:
arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.text+0x8a70): undefined reference to `pm44xx_errata'
Fixes: c962184 (ARM: OMAP4: PM: add errata support)
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.ocm>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an interrupt has become active on the INTC it will stay active
until it is acked, even if masked or de-asserted. The
INTC_PENDING_IRQn registers are however updated and since these are
used by omap_intc_handle_irq to determine which interrupt to handle,
it will never see the active interrupt. This will result in a storm of
useless interrupts that is only stopped when another higher priority
interrupt is asserted.
Fix by sending the INTC an acknowledge if we find no interrupts to
handle.
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5 has the same iommus as OMAP4, so extend the OMAP4
iommu pdata quirks for OMAP5 as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A new MMU hwmod class and data structures are created
to represent the MMUs within the IPU and DSP processor
subsystems in OMAP5. The MMUs in OMAP5 are identical to
those in OMAP4.
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP iommu driver performs the reset management for the
iommu instances in processor sub-systems using the omap_device
API which are currently supplied as platform data ops. Use pdata
quirks to maintain the functionality as the OMAP iommu driver
gets converted to use DT nodes, until the reset portions are
decoupled from omap_hwmod/omap_device into a separate reset
driver.
This patch adds the pdata quirks for the reset management of
iommus within the DSP (OMAP3 & OMAP4) and IPU subsystems (OMAP4).
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IOMMU DT adaptation support uses the device name instead
of an iommu object name. Fixup the ISP device archdata MMU
name at runtime if using DT-boot. This allows the OMAP3 camera
to be functional in both legacy and DT boots. The iommu object
names should eventually vanish when all the IOMMU users have
been converted to DT nodes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA MMU is not functional when used through the hwmod and
omap_device layers. Add fixes to clockdomain and hwmod data
to have it functional. The hwmod changes are needed to enable
the clock, and the SWSUP change is needed to wakeup the domain
because the power domain is programmed to be in RET, and there
is no automatic power domain switching to ON.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_OMAP_IOMMU_IVA2 was defined originally to avoid conflicting
usage by tidspbridge and other iommu users. The same can be achieved
by marking the DT node disabled, so remove this obsolete flag and
the corresponding hwmod data can be enabled.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: revise commit log]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX SoC changes for 3.15 from Shawn Guo:
- Support suspend from ocram (DDR IO floating) for imx6 platforms
- Add cpuidle support for imx6sl
- Sparse warning fixes for imx6sl and vf610 clock code
- Remove PWM platform code
- Support ptp and rmii clock from pad
- Support WEIM CS GPR configuration
- Random cleanups and defconfig updates
* tag 'imx-soc-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (373 commits)
ARM: imx6: drop .text.head section annotation from headsmp.S
ARM: imx6: build suspend-imx6.o with CONFIG_SOC_IMX6
ARM: imx6: rename pm-imx6q.c to pm-imx6.c
ARM: imx6: introduce CONFIG_SOC_IMX6 for i.MX6 common stuff
ARM: imx6: do not call imx6q_suspend_init() with !CONFIG_SUSPEND
ARM: imx6: call suspend_set_ops() from suspend routine
ARM: imx6: build headsmp.o only on CONFIG_SMP
ARM: imx6: move v7_cpu_resume() into suspend-imx6.S
ARM i.MX6q: Mark VPU and IPU AXI transfers as cacheable, increase IPU priority
ARM: imx6q: Add GPR6 and GPR7 register definitions for iomuxc gpr
bus: imx-weim: support CS GPR configuration
ARM: mach-imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX2_WDT from SOC_IMX53
ARM: imx_v6_v7_defconfig: Select CONFIG_DEBUG_FS
ARM: mach-imx: Select CONFIG_SRAM at ARCH_MXC level
ARM: imx: add speed grading check for i.mx6 soc
ARM: imx: avoid calling clk APIs in idle thread which may cause schedule
ARM: imx6q: support ptp and rmii clock from pad
ARM: imx6q: remove unneeded clk lookups
ARM: imx_v6_v7_defconfig: Select CONFIG_MMC_UNSAFE_RESUME
ARM: imx_v4_v5_defconfig: Select CONFIG_MMC_UNSAFE_RESUME
...
Merge OMAP crossbar support from Tony Lindgren:
Add support for GIC crossbar that routes interrupts on newer omaps.
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
* tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA: Enable Crossbar IP support for DRA7XX
ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
Signed-off-by: Olof Johansson <olof@lixom.net>
Power, reset and clock related changes via Paul Walmsley <paul@pwsan.com>, via
Tony Lindgren:
Some low-level optimizations and fixes that don't belong in an -rc
series for various OMAP-family chips, targeted for v3.15.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/prcm-a-for-v3.15/20140228124518/
* tag 'omap-for-v3.15/prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: DPLL: stop reparenting to same parent if already done
ARM: OMAP2+: clock: fix rate prints
ARM: AM43x: hwmod data: register spinlock OCP interface
ARM: OMAP2+: clockdomain: Reintroduce SW_SLEEP Support
ARM: OMAP2+: AM43xx: implement support for machine restart
Signed-off-by: Olof Johansson <olof@lixom.net>
OMAP SoC changes from Tony Lindgren:
Few SoC related improvments for omaps.
* tag 'omap-for-v3.15/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: remove OMAP_PACKAGE_ZAC and OMAP_PACKAGE_ZAF
ARM: OMAP2+: AM43x: Use gptimer as clocksource
ARM: OMAP2+: AM43x: determine features
ARM: OMAP2+: AM43x: Add ID for ES1.1
ARM: OMAP2+: AM43x: enable in default config
Signed-off-by: Olof Johansson <olof@lixom.net>
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
Conflicts:
arch/arm/mach-omap2/Kconfig
The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.
Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As OMAP2+ is moving to a full DT boot for all SoC families, commit
7ce93f3 "ARM: OMAP2+: Fix more missing data for omap3.dtsi file"
adds basic DT bits for OMAP3. But the driver is not yet converted,
so this will not work and driver will not be probed. Convert it!
The legacy boot mode is still supported until OMAP3 is converted
to DT-boot only.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: dev_name adaptation and improved error checking]
Signed-off-by: Suman Anna <s-anna@ti.com>
[tony@atomide.com: Ack for arch/arm/*omap* parts]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This patch
- refactors gpmc_hwecc_bch_capable()
- add checks for new platforms like dra7xx, am43xx
- add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
commit ac65caf514
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Kconfig symbols OMAP_PACKAGE_ZAC and OMAP_PACKAGE_ZAF were added in
v2.6.36. They have never been used. Setting them has no effect. These
symbols can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[tony@atomide.com: updated to remove also the related mux.h entries]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SyncTimer in AM43x is clocked using the following two sources:
1) An inaccuarte 32k clock (CLK_32KHZ) derived from PER DPLL, causing system
time to go slowly (~10% deviation).
2) external 32KHz RTC clock, which may not always be available on board like
in the case of ePOS EVM
Use gptimer as clocksource instead, as is done in the case of AM335x
(which does not have a SyncTimer). With this, system time keeping works
accurately.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine AM43x device features by reusing AM335x helper as feature
register layout is similar.
And also exporting AM43xx family name.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.
sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.
Add quirks code to handle proper reset pulse signal.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_noncore_dpll_set_rate forces a reparent to the same clk_ref
for every call that takes place. This is an can be done only if a change
is detected.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Printing with unsigned long rates with %ld gives wrong result if the
rate is high enough. Fix this by using %lu.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM43xx has a spinlock module which is identical to the
one present on AM33xx. Register the spinlock ocp_if link
so that the spinlock hwmod and associated omap_device can
be instantiated, and the runtime pm API could be used by
the OMAP hwspinlock driver.
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since commit 65aa94b204 (ARM: OMAP4: clockdomain/CM code: Update supported
transition modes), on OMAP4, all CLKDMs support HW_AUTO so this is used
instead of SW_SLEEP for the idling of clockdomains. However, additional
SoCs now leverage the OMAP4 clockdomain code so update it to use SW_SLEEP
if the clockdomain data specifies that the CLKDM has the
CLKDM_CAN_FORCE_SLEEP flag set rather than using HW_AUTO for both cases.
Without this patch, clockdomain handling is broken on AM43xx and no
clockdomains are actually being put into idle on this platform. Any
attempt to idle them results in the HW_AUTO value (0x3) being written
to them with no apparent effect.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: added extra explanatory text from patch set intro]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add restart hook so that AM4372 builds can restart the platform.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251. Change the platform data built-in
block and board files accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge "kconfig clean-up and mach-virt removal for 3.15" from Rob Herring
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
* tag 'kconfig-cleanup-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
ARM: virt: select ARM_AMBA
ARM: virt: make mach-virt just a kconfig option
ARM: vt8500: enable V6K instead of plain V6
ARM: cns3xxx: enable V6K instead of plain V6
ARM: bcm2835: enable V6K instead of plain V6
ARM: Select V6K instead of V6 by default for multi-platform
ARM: select MIGHT_HAVE_CACHE_L2X0 for V6 and V7 multi-platform
ARM: select HAVE_SMP for V7 multi-platform
ARM: centralize common multi-platform kconfig options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Omap fixes from Tony Lindgren:
Fixes for omaps mostly to fix the 3430 display regression,
and random crashes if booting n900 with device tree and
thumb mode. Also few other regressions and fixes.
* tag 'omap-for-v3.14/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix pinctrl interrupts for core2
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omapdss driver no longer uses get_context_loss_count call, so we can
remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
After splitting padconf core into two parts to avoid exposing
unaccessable registers, the new padconf core2 domain was left
without a wake-up interrupt.
Fix the issue by passing the shared wake-up interrupt in
platform data like we do for padconf core and wkup domains
already.
Fixes: 3d49538364 (ARM: dts: Split omap3 pinmux core device)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Delete ARM's asm/system.h. It's the last holdout and should be got rid of.
This builds for defconfig, lpc32xx_defconfig, exynos_defconfig + XEN, the
previous changed to a Gemini system and an omap3 config with TI_DAVINCI_EMAC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The camera sensor will soon require regulators and clocks. Register
fixed regulators for its VAA and VDD power supplies and a fixed rate
clock for its master clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
for non SMP build, NR_CPUS is 1 and hence the code complains with below
warnings.
arch/arm/mach-omap2/cpuidle44xx.c:207:8: warning: array subscript is above array bounds [-Warray-bounds]
arch/arm/mach-omap2/cpuidle44xx.c:212:11: warning: array subscript is above array bounds [-Warray-bounds]
Kill it by making array size fixed.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
