Also spur channel count and range is different for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper function would be used for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Have it in ah->caps. This will be used during various
calibrations.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 is a single chain and single band (2.4 Ghz) chip.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9300RateSize is not necessarily a power of 4.
Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.
ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ath_printk and ath_<level> similar to
dev_printk and dev_<level> from device.h
This allows a more gradual rename of ath_print
to to ath_dbg or perhaps ath_debug.
This basically removes debug.h leaving
only an #define ath_printk ath_dbg
there and moving all the ATH_DBG_<foo>
enums to ath.h
I do not think there's much purpose for struct
ath_common * being passed to the ath_printk
functions, but perhaps there might be.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The card doesn't support MFP, so silently accept DISABLED and OPTIONAL
settings.
This avoids the following failure in wpa_supplicant logs:
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
wpa_driver_wext_associate: assoc failed because set_auth_param(IW_AUTH_MFP) failed
Association request to the driver failed
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call netif_napi_{add,del}() on the NAPI contexts in the new and
old channels, respectively.
Since efx_init_napi() cannot fail, make its return type void.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are using a legacy interrupt, our IRQ may be shared and our
interrupt handler may be called even though interrupts are disabled on
the NIC. When we change ring sizes, we reallocate the event queue and
the interrupt handler may use an invalid pointer when called for
another device's interrupt.
Maintain a legacy_irq_enabled flag and test that at the top of the
interrupt handler. Note that this problem results from the need to
work around broken INT_ISR0 reads, and does not affect the legacy
interrupt handler for Falcon A1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move search_depth arrays into per-table state.
Define initialisation function efx_filter_init_rx() which sets
everything apart from the match fields.
Define efx_filter_set_{ipv4_local,ipv4_full,eth_local}() to set the
match fields. This allows some simplification of callers and later
support for additional protocols and more flexible matching using
multiple calls to these functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The separation between filter tables is largely an internal detail
and it may be removed in future hardware. To prepare for that:
- Merge table ID with filter index to make an opaque filter ID
- Wrap efx_filter_table_clear() with a function that clears filters
from both RX tables, which is all that the current caller requires
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add message at start of self-test and increase log level of message at
end of self-test, so that any other messages produced during the
test are clearly associated with it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Whenever we add DMA descriptors to a TX ring and update the ring
pointer, the TX DMA engine must first read the new DMA descriptors and
then start reading packet data. However, all released Solarflare 10G
controllers have a 'TX push' feature that allows us to reduce latency
by writing the first new DMA descriptor along with the pointer update.
This is only useful when the queue is empty. The hardware should
ignore the pushed descriptor if the queue is not empty, but this check
is buggy, so we must do it in software.
In order to tell whether a TX queue is empty, we need to compare the
previous transmission count (write_count) and completion count
(read_count). However, if we do that every time we update the ring
pointer then read_count may ping-pong between the caches of two CPUs
running the transmission and completion paths for the queue.
Therefore, we split the check for an empty queue between the
completion path and the transmission path:
- Add an empty_read_count field representing a point at which the
completion path saw the TX queue as empty.
- Add an old_write_count field for use on the completion path.
- On the completion path, whenever read_count reaches or passes
old_write_count the TX queue may be empty. We then read
write_count, set empty_read_count if read_count == write_count,
and update old_write_count.
- On the transmission path, we read empty_read_count. If it's set, we
compare it with the value of write_count before the current set of
descriptors was added. If they match, the queue really is empty and
we can use TX push.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
It is not necessary to serialise writes to the paged 128-bit
registers. However, if we don't then we must always write the last
dword separately, not as part of a qword write.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Document exactly which registers and functions have special behaviour,
and why races on writes to descriptor pointers are safe.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Place the regularly updated fields (locks, MAC stats, etc.) on a
separate cache-line from fields which are mostly constant. This
should reduce cache misses for access to the latter on the data path.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
struct net_device has its own struct net_device_stats member, so use
this one instead of a private copy in struct net_local.
Note: This patch was not even compile tested.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
xemaclite_get_stats() just returns dev->stats so we can leave it out
alltogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
am79c961_getstats() just returns dev->stats so we can leave it out
alltogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch helps prevent FW/SW semaphore collision from leading
to link establishment failure. The collision might mess up the
PHY registers so we reset the PHY. However there are SFI/KR areas
in the PHY that are not reset with a Reset_AN so we need to change
LMS to reset it. Also wait until AN state machine is AN_GOOD
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.
Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.
Tested on 3945, 4965, 5300, 6300.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similarly like on iwlagn, initialize reset duration on iwl3945 to prevent
too frequent firmware resets.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we report tx acks to the protocol stack, add the needed
flag to hw_flags. This way we'll also use the new AP probing mechanism.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
