Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Decrease polling rate for erase/trim/discard
   - Allow non-sleeping GPIOs for card detect
   - Improve mmc block removal path
   - Enable support for mmc_sw_reset() for SDIO cards
   - Add mmc_sw_reset() to allow users to do a soft reset of the card
   - Allow power delay to be tunable via DT
   - Allow card detect debounce delay to be tunable via DT
   - Enable new quirk to limit clock rate for Marvell 8887 chip
   - Don't show eMMC RPMB and BOOT areas in /proc/partitions
   - Add capability to avoid 3.3V signaling for fragile HWs

  MMC host:
   - Improve/fixup support for handle highmem pages
   - Remove depends on HAS_DMA in case of platform dependency
   - mvsdio: Enable support for erase/trim/discard
   - rtsx_usb: Enable support for erase/trim/discard
   - renesas_sdhi: Fix WP logic regressions
   - renesas_sdhi: Add r8a77965 support
   - renesas_sdhi: Add R8A77980 to whitelist
   - meson: Add optional support for device reset
   - meson: Add support for the Meson-AXG platform
   - dw_mmc: Add new driver for BlueField DW variant
   - mediatek: Add support for 64G DRAM DMA
   - sunxi: Deploy runtime PM support
   - jz4740: Add support for JZ4780
   - jz4740: Enable support for DT based platforms
   - sdhci: Various improvement to timeout handling
   - sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
   - sdhci-omap: Add support for controller in k2g SoC
   - sdhci-omap: Add workarounds for a couple of Erratas
   - sdhci-omap: Enable support for generic sdhci DT properties
   - sdhci-cadence: Re-send tune request to deal with errata
   - sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
   - sdhci-pci: Avoid 3.3V signaling on some NI 904x
   - sdhci-esdhc-imx: Use watermark levels for PIO access
   - sdhci-msm: Improve card detection handling
   - sdhci-msm: Add support voltage pad switching"

* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
  mmc: renesas_sdhi: really fix WP logic regressions
  mmc: mvsdio: Enable MMC_CAP_ERASE
  mmc: mvsdio: Respect card busy time out from mmc core
  mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
  mmc: sunxi: Use ifdef rather than __maybe_unused
  mmc: mxmmc: Use ifdef rather than __maybe_unused
  mmc: mxmmc: include linux/highmem.h
  mmc: sunxi: mark PM functions as __maybe_unused
  mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
  mmc: au1xmmc: handle highmem pages
  mmc: Allow non-sleeping GPIO cd
  mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
  mmc: sd: Define name for default speed dtr
  mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
  mmc: sdhci-xenon: use match_string() helper
  mmc: wbsd: handle highmem pages
  mmc: ushc: handle highmem pages
  mmc: mxcmmc: handle highmem pages
  mmc: atmel-mci: use sg_copy_{from,to}_buffer
  mmc: android-goldfish: use sg_copy_{from,to}_buffer
  ...

arch/mips/boot/dts/ingenic/ci20.dts

@@ -36,6 +36,28 @@
 	clock-frequency = <48000000>;
 };
 
+&mmc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc0>;
+
+	cd-gpios = <&gpf 20 GPIO_ACTIVE_LOW>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+};
+
 &uart0 {
 	status = "okay";
 
@@ -203,4 +225,16 @@
 		groups = "nemc-cs6";
 		bias-disable;
 	};
+
+	pins_mmc0: mmc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit-e", "mmc0-4bit-e";
+		bias-disable;
+	};
+
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit-d", "mmc1-4bit-d";
+		bias-disable;
+	};
 };

arch/mips/boot/dts/ingenic/jz4780.dtsi

@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/clock/jz4780-cgu.h>
+#include <dt-bindings/dma/jz4780-dma.h>
 
 / {
 	#address-cells = <1>;
@@ -241,6 +242,57 @@
 		status = "disabled";
 	};
 
+	dma: dma@13420000 {
+		compatible = "ingenic,jz4780-dma";
+		reg = <0x13420000 0x10000>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu JZ4780_CLK_PDMA>;
+	};
+
+	mmc0: mmc@13450000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu JZ4780_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mmc1: mmc@13460000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu JZ4780_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC1_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
 	bch: bch@134d0000 {
 		compatible = "ingenic,jz4780-bch";
 		reg = <0x134d0000 0x10000>;