Merge branches 'clk-spreadtrum', 'clk-stm32f', 'clk-stm32mp1', 'clk-hi655x' and 'clk-gpio' into clk-next

* clk-spreadtrum:
  clk: sprd: add RTC gate for SC9860
  dt-bindings: clocks: add APB RTC gate for SC9860

* clk-stm32f:
  clk: stm32: Add clk entry for SDMMC2 on stm32F769
  clk: stm32: Add DSI clock for STM32F469 Board
  clk: stm32: END_PRIMARY_CLK should be declare after CLK_SYSCLK

* clk-stm32mp1:
  clk: stm32: add configuration flags for each of the stm32 drivers
  clk: stm32mp1: add Debug clocks
  clk: stm32mp1: add MCO clocks
  clk: stm32mp1: add RTC clock
  clk: stm32mp1: add Peripheral & Kernel Clocks
  clk: stm32mp1: add Kernel timers
  clk: stm32mp1: add Sub System clocks
  clk: stm32mp1: add Post-dividers for PLL
  clk: stm32mp1: add PLL clocks
  clk: stm32mp1: add Source Clocks for PLLs
  clk: stm32mp1: add MP1 gate for hse/hsi/csi oscillators
  clk: stm32mp1: Introduce STM32MP1 clock driver
  dt-bindings: Document STM32MP1 Reset Clock Controller (RCC) bindings

* clk-hi655x:
  clk: enable hi655x common clk automatically

* clk-gpio:
  clk: clk-gpio: Allow GPIO to sleep in set/get_parent

Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt

@@ -0,0 +1,60 @@
+STMicroelectronics STM32 Peripheral Reset Clock Controller
+==========================================================
+
+The RCC IP is both a reset and a clock controller.
+
+RCC makes also power management (resume/supend and wakeup interrupt).
+
+Please also refer to reset.txt for common reset controller binding usage.
+
+Please also refer to clock-bindings.txt for common clock controller
+binding usage.
+
+
+Required properties:
+- compatible: "st,stm32mp1-rcc", "syscon"
+- reg: should be register base and length as documented in the datasheet
+- #clock-cells: 1, device nodes should specify the clock in their
+  "clocks" property, containing a phandle to the clock device node,
+  an index specifying the clock to use.
+- #reset-cells: Shall be 1
+- interrupts: Should contain a general interrupt line and a interrupt line
+  to the wake-up of processor (CSTOP).
+
+Example:
+	rcc: rcc@50000000 {
+		compatible = "st,stm32mp1-rcc", "syscon";
+		reg = <0x50000000 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>,
+			     <GIC_SPI 145 IRQ_TYPE_NONE>;
+	};
+
+Specifying clocks
+=================
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/stm32mp1-clks.h header and can be used in device
+tree sources.
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the reset device node and an index specifying
+which channel to use.
+The index is the bit number within the RCC registers bank, starting from RCC
+base address.
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register.
+
+For example on STM32MP1, for LTDC reset:
+ ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset
+      = 0x180 / 4 * 32 + 0 = 3072
+
+The list of valid indices for STM32MP1 is available in:
+include/dt-bindings/reset-controller/stm32mp1-resets.h
+
+This file implements defines like:
+#define LTDC_R	3072