dt-bindings: consolidate various misc bindings
Move various bindings in misc to appropriate subsystem directories. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org>
This commit is contained in:
Rob Herring
@@ -1,24 +0,0 @@
|
||||
BMP085/BMP18x digital pressure sensors
|
||||
|
||||
Required properties:
|
||||
- compatible: bosch,bmp085
|
||||
|
||||
Optional properties:
|
||||
- chip-id: configurable chip id for non-default chip revisions
|
||||
- temp-measurement-period: temperature measurement period (milliseconds)
|
||||
- default-oversampling: default oversampling value to be used at startup,
|
||||
value range is 0-3 with rising sensitivity.
|
||||
- interrupt-parent: should be the phandle for the interrupt controller
|
||||
- interrupts: interrupt mapping for IRQ
|
||||
|
||||
Example:
|
||||
|
||||
pressure@77 {
|
||||
compatible = "bosch,bmp085";
|
||||
reg = <0x77>;
|
||||
chip-id = <10>;
|
||||
temp-measurement-period = <100>;
|
||||
default-oversampling = <2>;
|
||||
interrupt-parent = <&gpio0>;
|
||||
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
|
Before Width: | Height: | Size: 701 B |
@@ -1,119 +0,0 @@
|
||||
LIS302 accelerometer devicetree bindings
|
||||
|
||||
This device is matched via its bus drivers, and has a number of properties
|
||||
that apply in on the generic device (independent from the bus).
|
||||
|
||||
|
||||
Required properties for the SPI bindings:
|
||||
- compatible: should be set to "st,lis3lv02d_spi"
|
||||
- reg: the chipselect index
|
||||
- spi-max-frequency: maximal bus speed, should be set to 1000000 unless
|
||||
constrained by external circuitry
|
||||
- interrupts: the interrupt generated by the device
|
||||
|
||||
Required properties for the I2C bindings:
|
||||
- compatible: should be set to "st,lis3lv02d"
|
||||
- reg: i2c slave address
|
||||
- Vdd-supply: The input supply for Vdd
|
||||
- Vdd_IO-supply: The input supply for Vdd_IO
|
||||
|
||||
|
||||
Optional properties for all bus drivers:
|
||||
|
||||
- st,click-single-{x,y,z}: if present, tells the device to issue an
|
||||
interrupt on single click events on the
|
||||
x/y/z axis.
|
||||
- st,click-double-{x,y,z}: if present, tells the device to issue an
|
||||
interrupt on double click events on the
|
||||
x/y/z axis.
|
||||
- st,click-thresh-{x,y,z}: set the x/y/z axis threshold
|
||||
- st,click-click-time-limit: click time limit, from 0 to 127.5msec
|
||||
with step of 0.5 msec
|
||||
- st,click-latency: click latency, from 0 to 255 msec with
|
||||
step of 1 msec.
|
||||
- st,click-window: click window, from 0 to 255 msec with
|
||||
step of 1 msec.
|
||||
- st,irq{1,2}-disable: disable IRQ 1/2
|
||||
- st,irq{1,2}-ff-wu-1: raise IRQ 1/2 on FF_WU_1 condition
|
||||
- st,irq{1,2}-ff-wu-2: raise IRQ 1/2 on FF_WU_2 condition
|
||||
- st,irq{1,2}-data-ready: raise IRQ 1/2 on data ready contition
|
||||
- st,irq{1,2}-click: raise IRQ 1/2 on click condition
|
||||
- st,irq-open-drain: consider IRQ lines open-drain
|
||||
- st,irq-active-low: make IRQ lines active low
|
||||
- st,wu-duration-1: duration register for Free-Fall/Wake-Up
|
||||
interrupt 1
|
||||
- st,wu-duration-2: duration register for Free-Fall/Wake-Up
|
||||
interrupt 2
|
||||
- st,wakeup-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
|
||||
upper/lower limit
|
||||
- st,wakeup-threshold: set wakeup threshold
|
||||
- st,wakeup2-{x,y,z}-{lo,hi}: set wakeup condition on x/y/z axis for
|
||||
upper/lower limit for second wakeup
|
||||
engine.
|
||||
- st,wakeup2-threshold: set wakeup threshold for second wakeup
|
||||
engine.
|
||||
- st,highpass-cutoff-hz=: 1, 2, 4 or 8 for 1Hz, 2Hz, 4Hz or 8Hz of
|
||||
highpass cut-off frequency
|
||||
- st,hipass{1,2}-disable: disable highpass 1/2.
|
||||
- st,default-rate=: set the default rate
|
||||
- st,axis-{x,y,z}=: set the axis to map to the three coordinates.
|
||||
Negative values can be used for inverted axis.
|
||||
- st,{min,max}-limit-{x,y,z} set the min/max limits for x/y/z axis
|
||||
(used by self-test)
|
||||
|
||||
|
||||
Example for a SPI device node:
|
||||
|
||||
lis302@0 {
|
||||
compatible = "st,lis302dl-spi";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <1000000>;
|
||||
interrupt-parent = <&gpio>;
|
||||
interrupts = <104 0>;
|
||||
|
||||
st,click-single-x;
|
||||
st,click-single-y;
|
||||
st,click-single-z;
|
||||
st,click-thresh-x = <10>;
|
||||
st,click-thresh-y = <10>;
|
||||
st,click-thresh-z = <10>;
|
||||
st,irq1-click;
|
||||
st,irq2-click;
|
||||
st,wakeup-x-lo;
|
||||
st,wakeup-x-hi;
|
||||
st,wakeup-y-lo;
|
||||
st,wakeup-y-hi;
|
||||
st,wakeup-z-lo;
|
||||
st,wakeup-z-hi;
|
||||
};
|
||||
|
||||
Example for a I2C device node:
|
||||
|
||||
lis331dlh: lis331dlh@18 {
|
||||
compatible = "st,lis331dlh", "st,lis3lv02d";
|
||||
reg = <0x18>;
|
||||
Vdd-supply = <&lis3_reg>;
|
||||
Vdd_IO-supply = <&lis3_reg>;
|
||||
|
||||
st,click-single-x;
|
||||
st,click-single-y;
|
||||
st,click-single-z;
|
||||
st,click-thresh-x = <10>;
|
||||
st,click-thresh-y = <10>;
|
||||
st,click-thresh-z = <10>;
|
||||
st,irq1-click;
|
||||
st,irq2-click;
|
||||
st,wakeup-x-lo;
|
||||
st,wakeup-x-hi;
|
||||
st,wakeup-y-lo;
|
||||
st,wakeup-y-hi;
|
||||
st,wakeup-z-lo;
|
||||
st,wakeup-z-hi;
|
||||
st,min-limit-x = <120>;
|
||||
st,min-limit-y = <120>;
|
||||
st,min-limit-z = <140>;
|
||||
st,max-limit-x = <550>;
|
||||
st,max-limit-y = <550>;
|
||||
st,max-limit-z = <750>;
|
||||
};
|
||||
|
||||
@@ -1,20 +0,0 @@
|
||||
TI DAC7512 DEVICETREE BINDINGS
|
||||
|
||||
Required properties:
|
||||
|
||||
- "compatible" Must be set to "ti,dac7512"
|
||||
|
||||
Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
|
||||
apply. In particular, "reg" and "spi-max-frequency" properties must be given.
|
||||
|
||||
|
||||
Example:
|
||||
|
||||
spi_master {
|
||||
dac7512: dac7512@0 {
|
||||
compatible = "ti,dac7512";
|
||||
reg = <0>; /* CS0 */
|
||||
spi-max-frequency = <1000000>;
|
||||
};
|
||||
};
|
||||
|
||||
Reference in New Issue
Block a user