MIPS: TXx9: Make spi_eeprom.c more generic

Helper routines in txx9/rbtx4938/spi_eeprom.c is not TX4938 specific.
Move it to txx9/generic/ directory and make it works with SPI bus
number other than 0.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/txx9/generic/spi_eeprom.c
 delete mode 100644 arch/mips/txx9/rbtx4938/spi_eeprom.c

arch/mips/txx9/generic/Makefile

@@ -8,5 +8,6 @@ obj-$(CONFIG_SOC_TX3927)	+= setup_tx3927.o irq_tx3927.o
 obj-$(CONFIG_SOC_TX4927)	+= mem_tx4927.o setup_tx4927.o irq_tx4927.o
 obj-$(CONFIG_SOC_TX4938)	+= mem_tx4927.o setup_tx4938.o irq_tx4938.o
 obj-$(CONFIG_TOSHIBA_FPCIB0)	+= smsc_fdc37m81x.o
+obj-$(CONFIG_SPI)		+= spi_eeprom.o
 
 EXTRA_CFLAGS += -Werror

arch/mips/txx9/generic/spi_eeprom.c

@@ -0,0 +1,103 @@
+/*
+ * spi_eeprom.c
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * 2003-2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Support for TX4938 in 2.6 - Manish Lachwani (mlachwani@mvista.com)
+ */
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/eeprom.h>
+#include <asm/txx9/spi.h>
+
+#define AT250X0_PAGE_SIZE	8
+
+/* register board information for at25 driver */
+int __init spi_eeprom_register(int busid, int chipid, int size)
+{
+	struct spi_board_info info = {
+		.modalias = "at25",
+		.max_speed_hz = 1500000,	/* 1.5Mbps */
+		.bus_num = busid,
+		.chip_select = chipid,
+		/* Mode 0: High-Active, Sample-Then-Shift */
+	};
+	struct spi_eeprom *eeprom;
+	eeprom = kzalloc(sizeof(*eeprom), GFP_KERNEL);
+	if (!eeprom)
+		return -ENOMEM;
+	strcpy(eeprom->name, "at250x0");
+	eeprom->byte_len = size;
+	eeprom->page_size = AT250X0_PAGE_SIZE;
+	eeprom->flags = EE_ADDR1;
+	info.platform_data = eeprom;
+	return spi_register_board_info(&info, 1);
+}
+
+/* simple temporary spi driver to provide early access to seeprom. */
+
+static struct read_param {
+	int busid;
+	int chipid;
+	int address;
+	unsigned char *buf;
+	int len;
+} *read_param;
+
+static int __init early_seeprom_probe(struct spi_device *spi)
+{
+	int stat = 0;
+	u8 cmd[2];
+	int len = read_param->len;
+	char *buf = read_param->buf;
+	int address = read_param->address;
+
+	dev_info(&spi->dev, "spiclk %u KHz.\n",
+		 (spi->max_speed_hz + 500) / 1000);
+	if (read_param->busid != spi->master->bus_num ||
+	    read_param->chipid != spi->chip_select)
+		return -ENODEV;
+	while (len > 0) {
+		/* spi_write_then_read can only work with small chunk */
+		int c = len < AT250X0_PAGE_SIZE ? len : AT250X0_PAGE_SIZE;
+		cmd[0] = 0x03;	/* AT25_READ */
+		cmd[1] = address;
+		stat = spi_write_then_read(spi, cmd, sizeof(cmd), buf, c);
+		buf += c;
+		len -= c;
+		address += c;
+	}
+	return stat;
+}
+
+static struct spi_driver early_seeprom_driver __initdata = {
+	.driver = {
+		.name	= "at25",
+		.owner	= THIS_MODULE,
+	},
+	.probe	= early_seeprom_probe,
+};
+
+int __init spi_eeprom_read(int busid, int chipid, int address,
+			   unsigned char *buf, int len)
+{
+	int ret;
+	struct read_param param = {
+		.busid = busid,
+		.chipid = chipid,
+		.address = address,
+		.buf = buf,
+		.len = len
+	};
+
+	read_param = &param;
+	ret = spi_register_driver(&early_seeprom_driver);
+	if (!ret)
+		spi_unregister_driver(&early_seeprom_driver);
+	return ret;
+}