Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Most notable:

   - introducing the i2c_quirk infrastructure.  Now, flaws of I2C
     controllers can be described and the core will check if the flaws
     collide with the messages to be sent

   - wait_for_completion return type cleanup series

   - new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780

   - updates to the I2C slave framework which include API changes.  Its
     only user was updated, too.  Documentation was finally added

   - changed dynamic bus numbering for the DT case.  This could change
     bus numbers for users.  However, it fixes a collision where dynamic
     and static busses request the same id.

   - driver bugfixes, cleanups"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
  i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
  of: Add vendor prefix 'netlogic'
  i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
  i2c: davinci: use bus recovery infrastructure
  i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
  i2c: i2c-mux-gpio: remove error messages for probe deferrals
  i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
  i2c: dln2: set the device tree node of the adapter
  i2c: davinci: fixup wait_for_completion_timeout handling
  i2c: mpc: Fix ISR return value
  i2c: slave-eeprom: add more info when to increase the pointer
  i2c: slave: add documentation for i2c-slave-eeprom
  Documentation: i2c: describe the new slave mode
  i2c: slave: rework the slave API
  i2c: add support for the Digicolor I2C controller
  i2c: busses with dynamic ids should start after fixed ids for DT
  of: base: add function to get highest id of an alias stem
  i2c: designware: Suppress error message if platform_get_irq() < 0
  i2c: mpc: assign the correct prescaler from SVR
  i2c: img-scb: fixup of wait_for_completion_timeout return handling
  ...

Documentation/devicetree/bindings/i2c/i2c-davinci.txt

@@ -10,6 +10,9 @@ Required properties:
 Recommended properties :
 - interrupts : standard interrupt property.
 - clock-frequency : desired I2C bus clock frequency in Hz.
+- ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC
+	registers. PFUNC registers allow to switch I2C pins to function as
+	GPIOs, so they can by toggled manually.
 
 Example (enbw_cmc board):
 	i2c@1c22000 {

Documentation/devicetree/bindings/i2c/i2c-digicolor.txt

@@ -0,0 +1,25 @@
+Conexant Digicolor I2C controller
+
+Required properties:
+ - compatible: must be "cnxt,cx92755-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Example:
+
+	i2c: i2c@f0000120 {
+		compatible = "cnxt,cx92755-i2c";
+		reg = <0xf0000120 0x10>;
+		interrupts = <28>;
+		clocks = <&main_clk>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};

Documentation/devicetree/bindings/i2c/i2c-jz4780.txt

@@ -0,0 +1,35 @@
+* Ingenic JZ4780 I2C Bus controller
+
+Required properties:
+- compatible: should be "ingenic,jz4780-i2c"
+- reg: Should contain the address & size of the I2C controller registers.
+- interrupts: Should specify the interrupt provided by parent.
+- clocks: Should contain a single clock specifier for the JZ4780 I2C clock.
+- clock-frequency: desired I2C bus clock frequency in Hz.
+
+Recommended properties:
+- pinctrl-names: should be "default";
+- pinctrl-0: phandle to pinctrl function
+
+Optional properties:
+- interrupt-parent: Should be the phandle of the interrupt controller that
+  delivers interrupts to the I2C block.
+
+Example
+
+/ {
+	i2c4: i2c4@0x10054000 {
+		compatible = "ingenic,jz4780-i2c";
+		reg = <0x10054000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <56>;
+
+		clocks = <&cgu JZ4780_CLK_SMB4>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c4_data>;
+
+	};
+};
+

Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt

@@ -0,0 +1,22 @@
+Device tree configuration for the I2C controller on the XLP9xx/5xx SoC
+
+Required properties:
+- compatible      : should be "netlogic,xlp980-i2c"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+
+Optional properties:
+- clock-frequency : frequency of bus clock in Hz
+                    Defaults to 100 KHz when the property is not specified
+
+Example:
+
+i2c0: i2c@113100 {
+	compatible = "netlogic,xlp980-i2c";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0 0x113100 0x100>;
+	clock-frequency = <400000>;
+	interrupts = <30>;
+	interrupt-parent = <&pic>;
+};