Spelling fix: explicitly

From: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>

arch/cris/arch-v10/kernel/entry.S

@@ -97,7 +97,7 @@
  *
  *  Revision 1.36  2001/11/22 13:36:36  bjornw
  *  * In ret_from_intr, check regs->dccr for usermode reentrance instead of
- *    DCCR explicitely (because the latter might not reflect current reality)
+ *    DCCR explicitly (because the latter might not reflect current reality)
  *  * In mmu_bus_fault, set $r9 _after_ calling the C-code instead of before
  *    since $r9 is call-clobbered and is potentially needed afterwards
  *

arch/cris/arch-v10/kernel/kgdb.c

@@ -959,7 +959,7 @@ stub_is_stopped(int sigval)
 
 	/* Send register contents. We probably only need to send the
 	 * PC, frame pointer and stack pointer here. Other registers will be
-	 * explicitely asked for. But for now, send all. 
+	 * explicitly asked for. But for now, send all.
 	 */
 	
 	for (regno = R0; regno <= USP; regno++) {

arch/cris/arch-v10/lib/dram_init.S

@@ -40,7 +40,7 @@
  * Copy warning from head.S about r8 and r9
  *
  * Revision 1.7  2001/04/18 12:05:39  bjornw
- * Fixed comments, and explicitely include config.h to be sure its there
+ * Fixed comments, and explicitly include config.h to be sure its there
  *
  * Revision 1.6  2001/04/10 06:20:16  starvik
  * Delay should be 200us, not 200ns
@@ -66,7 +66,7 @@
  */
 
 /* Just to be certain the config file is included, we include it here
- * explicitely instead of depending on it being included in the file that
+ * explicitly instead of depending on it being included in the file that
  * uses this code.
  */
 

arch/cris/arch-v32/lib/dram_init.S

@@ -12,7 +12,7 @@
  */
 
 /* Just to be certain the config file is included, we include it here
- * explicitely instead of depending on it being included in the file that
+ * explicitly instead of depending on it being included in the file that
  * uses this code.
  */
 

arch/powerpc/kernel/cpu_setup_6xx.S

@@ -113,7 +113,7 @@ setup_604_hid0:
  * around #3 and with the same fix we use. We may want to
  * check if the CPU is using 60x bus mode in which case
  * the workaround for errata #4 is useless. Also, we may
- * want to explicitely clear HID0_NOPDST as this is not
+ * want to explicitly clear HID0_NOPDST as this is not
  * needed once we have applied workaround #5 (though it's
  * not set by Apple's firmware at least).
  */

arch/powerpc/kernel/irq.c

@@ -491,7 +491,7 @@ struct irq_host *irq_alloc_host(struct device_node *of_node,
 
 			/* Legacy flags are left to default at this point,
 			 * one can then use irq_create_mapping() to
-			 * explicitely change them
+			 * explicitly change them
 			 */
 			ops->map(host, i, i);
 		}