Merge 5.6-rc5 into char-misc-next

We need the binder and other fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/admin-guide/acpi/fan_performance_states.rst

@@ -18,7 +18,7 @@ may look as follows::
 
  $ ls -l /sys/bus/acpi/devices/INT3404:00/
  total 0
-...
+ ...
  -r--r--r-- 1 root root 4096 Dec 13 20:38 state0
  -r--r--r-- 1 root root 4096 Dec 13 20:38 state1
  -r--r--r-- 1 root root 4096 Dec 13 20:38 state10
@@ -38,7 +38,7 @@ where each of the "state*" files represents one performance state of the fan
 and contains a colon-separated list of 5 integer numbers (fields) with the
 following interpretation::
 
-control_percent:trip_point_index:speed_rpm:noise_level_mdb:power_mw
+  control_percent:trip_point_index:speed_rpm:noise_level_mdb:power_mw
 
 * ``control_percent``: The percent value to be used to set the fan speed to a
   specific level using the _FSL object (0-100).

Documentation/admin-guide/bootconfig.rst

@@ -62,6 +62,30 @@ Or more shorter, written as following::
 In both styles, same key words are automatically merged when parsing it
 at boot time. So you can append similar trees or key-values.
 
+Same-key Values
+---------------
+
+It is prohibited that two or more values or arrays share a same-key.
+For example,::
+
+ foo = bar, baz
+ foo = qux  # !ERROR! we can not re-define same key
+
+If you want to append the value to existing key as an array member,
+you can use ``+=`` operator. For example::
+
+ foo = bar, baz
+ foo += qux
+
+In this case, the key ``foo`` has ``bar``, ``baz`` and ``qux``.
+
+However, a sub-key and a value can not co-exist under a parent key.
+For example, following config is NOT allowed.::
+
+ foo = value1
+ foo.bar = value2 # !ERROR! subkey "bar" and value "value1" can NOT co-exist
+
+
 Comments
 --------
 
@@ -102,9 +126,13 @@ Boot Kernel With a Boot Config
 ==============================
 
 Since the boot configuration file is loaded with initrd, it will be added
-to the end of the initrd (initramfs) image file. The Linux kernel decodes
-the last part of the initrd image in memory to get the boot configuration
-data.
+to the end of the initrd (initramfs) image file with size, checksum and
+12-byte magic word as below.
+
+[initrd][bootconfig][size(u32)][checksum(u32)][#BOOTCONFIG\n]
+
+The Linux kernel decodes the last part of the initrd image in memory to
+get the boot configuration data.
 Because of this "piggyback" method, there is no need to change or
 update the boot loader and the kernel image itself.
 

Documentation/admin-guide/kernel-parameters.txt

@@ -136,6 +136,10 @@
 			dynamic table installation which will install SSDT
 			tables to /sys/firmware/acpi/tables/dynamic.
 
+	acpi_no_watchdog	[HW,ACPI,WDT]
+			Ignore the ACPI-based watchdog interface (WDAT) and let
+			a native driver control the watchdog device instead.
+
 	acpi_rsdp=	[ACPI,EFI,KEXEC]
 			Pass the RSDP address to the kernel, mostly used
 			on machines running EFI runtime service to boot the