Merge 5.10.53 into android12-5.10-lts

Changes in 5.10.53 ARM: dts: gemini: rename mdio to the right name ARM: dts: gemini: add device_type on pci ARM: dts: rockchip: Fix thermal sensor cells o rk322x ARM: dts: rockchip: fix pinctrl sleep nodename for rk3036-kylin and rk3288 arm64: dts: rockchip: fix pinctrl sleep nodename for rk3399.dtsi ARM: dts: rockchip: Fix the timer clocks order ARM: dts: rockchip: Fix IOMMU nodes properties on rk322x ARM: dts: rockchip: Fix power-controller node names for rk3066a ARM: dts: rockchip: Fix power-controller node names for rk3188 ARM: dts: rockchip: Fix power-controller node names for rk3288 arm64: dts: rockchip: Fix power-controller node names for px30 arm64: dts: rockchip: Fix power-controller node names for rk3328 arm64: dts: rockchip: Fix power-controller node names for rk3399 reset: ti-syscon: fix to_ti_syscon_reset_data macro ARM: brcmstb: dts: fix NAND nodes names ARM: Cygnus: dts: fix NAND nodes names ARM: NSP: dts: fix NAND nodes names ARM: dts: BCM63xx: Fix NAND nodes names ARM: dts: Hurricane 2: Fix NAND nodes names ARM: dts: imx6: phyFLEX: Fix UART hardware flow control ARM: imx: pm-imx5: Fix references to imx5_cpu_suspend_info arm64: dts: rockchip: fix regulator-gpio states array ARM: dts: ux500: Fix interrupt cells ARM: dts: ux500: Rename gpio-controller node ARM: dts: ux500: Fix orientation of accelerometer ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value rtc: mxc_v2: add missing MODULE_DEVICE_TABLE kbuild: sink stdout from cmd for silent build ARM: dts: am57xx-cl-som-am57x: fix ti,no-reset-on-init flag for gpios ARM: dts: am437x-gp-evm: fix ti,no-reset-on-init flag for gpios ARM: dts: am335x: fix ti,no-reset-on-init flag for gpios ARM: dts: OMAP2+: Replace underscores in sub-mailbox node names arm64: dts: ti: k3-am654x/j721e/j7200-common-proc-board: Fix MCU_RGMII1_TXC direction ARM: tegra: wm8903: Fix polarity of headphones-detection GPIO in device-trees ARM: tegra: nexus7: Correct 3v3 regulator GPIO of PM269 variant arm64: dts: qcom: sc7180: Move rmtfs memory region ARM: dts: stm32: Remove extra size-cells on dhcom-pdk2 ARM: dts: stm32: Fix touchscreen node on dhcom-pdk2 ARM: dts: stm32: fix stm32mp157c-odyssey card detect pin ARM: dts: stm32: fix gpio-keys node on STM32 MCU boards ARM: dts: stm32: fix RCC node name on stm32f429 MCU ARM: dts: stm32: fix timer nodes on STM32 MCU to prevent warnings memory: tegra: Fix compilation warnings on 64bit platforms firmware: arm_scmi: Add SMCCC discovery dependency in Kconfig firmware: arm_scmi: Fix the build when CONFIG_MAILBOX is not selected ARM: dts: bcm283x: Fix up MMC node names ARM: dts: bcm283x: Fix up GPIO LED node names arm64: dts: juno: Update SCPI nodes as per the YAML schema ARM: dts: rockchip: fix supply properties in io-domains nodes ARM: dts: stm32: fix i2c node name on stm32f746 to prevent warnings ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15 ARM: dts: stm32: fix the Odyssey SoM eMMC VQMMC supply ARM: dts: stm32: Drop unused linux,wakeup from touchscreen node on DHCOM SoM ARM: dts: stm32: Rename spi-flash/mx66l51235l@N to flash@N on DHCOM SoM ARM: dts: stm32: fix stpmic node for stm32mp1 boards ARM: OMAP2+: Block suspend for am3 and am4 if PM is not configured soc/tegra: fuse: Fix Tegra234-only builds firmware: tegra: bpmp: Fix Tegra234-only builds arm64: dts: ls208xa: remove bus-num from dspi node arm64: dts: imx8mq: assign PCIe clocks thermal/core: Correct function name thermal_zone_device_unregister() thermal/drivers/rcar_gen3_thermal: Do not shadow rcar_gen3_ths_tj_1 thermal/drivers/imx_sc: Add missing of_node_put for loop iteration thermal/drivers/sprd: Add missing of_node_put for loop iteration kbuild: mkcompile_h: consider timestamp if KBUILD_BUILD_TIMESTAMP is set arch/arm64/boot/dts/marvell: fix NAND partitioning scheme rtc: max77686: Do not enforce (incorrect) interrupt trigger type scsi: aic7xxx: Fix unintentional sign extension issue on left shift of u8 scsi: libsas: Add LUN number check in .slave_alloc callback scsi: libfc: Fix array index out of bound exception scsi: qedf: Add check to synchronize abort and flush sched/fair: Fix CFS bandwidth hrtimer expiry type perf/x86/intel/uncore: Clean up error handling path of iio mapping thermal/core/thermal_of: Stop zone device before unregistering it s390/traps: do not test MONITOR CALL without CONFIG_BUG s390: introduce proper type handling call_on_stack() macro cifs: prevent NULL deref in cifs_compose_mount_options() firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string arm64: dts: marvell: armada-37xx: move firmware node to generic dtsi file Revert "swap: fix do_swap_page() race with swapoff" f2fs: Show casefolding support only when supported mm/thp: simplify copying of huge zero page pmd when fork mm/userfaultfd: fix uffd-wp special cases for fork() mm/page_alloc: fix memory map initialization for descending nodes usb: cdns3: Enable TDL_CHK only for OUT ep net: bcmgenet: ensure EXT_ENERGY_DET_MASK is clear net: dsa: mv88e6xxx: enable .port_set_policy() on Topaz net: dsa: mv88e6xxx: use correct .stats_set_histogram() on Topaz net: dsa: mv88e6xxx: enable .rmu_disable() on Topaz net: dsa: mv88e6xxx: enable devlink ATU hash param for Topaz net: ipv6: fix return value of ip6_skb_dst_mtu netfilter: ctnetlink: suspicious RCU usage in ctnetlink_dump_helpinfo net/sched: act_ct: fix err check for nf_conntrack_confirm vmxnet3: fix cksum offload issues for tunnels with non-default udp ports net/sched: act_ct: remove and free nf_table callbacks net: bridge: sync fdb to new unicast-filtering ports net: netdevsim: use xso.real_dev instead of xso.dev in callback functions of struct xfrmdev_ops net: bcmgenet: Ensure all TX/RX queues DMAs are disabled net: ip_tunnel: fix mtu calculation for ETHER tunnel devices net: moxa: fix UAF in moxart_mac_probe net: qcom/emac: fix UAF in emac_remove net: ti: fix UAF in tlan_remove_one net: send SYNACK packet with accepted fwmark net: validate lwtstate->data before returning from skb_tunnel_info() Revert "mm/shmem: fix shmem_swapin() race with swapoff" net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave() net: fddi: fix UAF in fza_probe dma-buf/sync_file: Don't leak fences on merge failure kbuild: do not suppress Kconfig prompts for silent build ARM: dts: aspeed: Fix AST2600 machines line names ARM: dts: tacoma: Add phase corrections for eMMC tcp: consistently disable header prediction for mptcp tcp: annotate data races around tp->mtu_info tcp: fix tcp_init_transfer() to not reset icsk_ca_initialized ipv6: tcp: drop silly ICMPv6 packet too big messages tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path tools: bpf: Fix error in 'make -C tools/ bpf_install' bpftool: Properly close va_list 'ap' by va_end() on error bpf: Track subprog poke descriptors correctly and fix use-after-free perf test bpf: Free obj_buf drm/panel: nt35510: Do not fail if DSI read fails udp: annotate data races around unix_sk(sk)->gso_size Linux 5.10.53 Signed-off-by: Greg Kroah-Hartman <gregkh@google.com> Change-Id: Iac8fe9cd2abb2d8dd993967205a97c89f01f3647
2021-07-25 15:37:14 +02:00
parent 90a010f605 71046eac2d
commit afe9ed0e13
199 changed files with 819 additions and 565 deletions
--- a/11
+++ b/11
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 10
-SUBLEVEL = 52
+SUBLEVEL = 53
 EXTRAVERSION =
 NAME = Dare mighty things

@@ -720,11 +720,12 @@ $(KCONFIG_CONFIG):
 # This exploits the 'multi-target pattern rule' trick.
 # The syncconfig should be executed only once to make all the targets.
 # (Note: use the grouped target '&:' when we bump to GNU Make 4.3)
-quiet_cmd_syncconfig = SYNC    $@
-      cmd_syncconfig = $(MAKE) -f $(srctree)/Makefile syncconfig
-
+#
+# Do not use $(call cmd,...) here. That would suppress prompts from syncconfig,
+# so you cannot notice that Kconfig is waiting for the user input.
 %/config/auto.conf %/config/auto.conf.cmd %/generated/autoconf.h: $(KCONFIG_CONFIG)
-	+$(call cmd,syncconfig)
+	$(Q)$(kecho) "  SYNC    $@"
+	$(Q)$(MAKE) -f $(srctree)/Makefile syncconfig
 else # !may-sync-config
 # External modules and some install targets need include/generated/autoconf.h
 # and include/config/auto.conf but do not care if they are up-to-date.
--- a/arch/arm/boot/dts/am335x-baltos.dtsi
+++ b/arch/arm/boot/dts/am335x-baltos.dtsi
@@ -393,10 +393,10 @@
 	status = "okay";
 };

-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };

-&gpio3 {
+&gpio3_target {
 	ti,no-reset-on-init;
 };
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -648,7 +648,7 @@
 	status = "okay";
 };

-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };

--- a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
+++ b/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
@@ -150,7 +150,7 @@
 	status = "okay";
 };

-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };

--- a/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi
+++ b/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi
@@ -353,7 +353,7 @@
 	status = "okay";
 };

-&gpio0 {
+&gpio0_target {
 	ti,no-reset-on-init;
 };

--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@@ -1723,7 +1723,7 @@
 			};
 		};

-		target-module@ae000 {			/* 0x481ae000, ap 56 3a.0 */
+		gpio3_target: target-module@ae000 {		/* 0x481ae000, ap 56 3a.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0xae000 0x4>,
 			      <0xae010 0x4>,
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -813,11 +813,14 @@
 	status = "okay";
 };

+&gpio5_target {
+	ti,no-reset-on-init;
+};
+
 &gpio5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&display_mux_pins>;
 	status = "okay";
-	ti,no-reset-on-init;

 	p8 {
 		/*
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/am437x-l4.dtsi
@@ -2033,7 +2033,7 @@
 			};
 		};

-		target-module@22000 {			/* 0x48322000, ap 116 64.0 */
+		gpio5_target: target-module@22000 {		/* 0x48322000, ap 116 64.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x22000 0x4>,
 			      <0x22010 0x4>,
--- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
@@ -454,20 +454,20 @@

 &mailbox5 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
 		status = "okay";
 	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
 		status = "okay";
 	};
 };

 &mailbox6 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
 		status = "okay";
 	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
 		status = "okay";
 	};
 };
@@ -610,12 +610,11 @@
 	>;
 };

-&gpio3 {
-	status = "okay";
+&gpio3_target {
 	ti,no-reset-on-init;
 };

-&gpio2 {
+&gpio2_target {
 	status = "okay";
 	ti,no-reset-on-init;
 };
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -156,10 +156,7 @@
 	/*W0-W7*/	"","","","","","","","",
 	/*X0-X7*/	"","","","","","","","",
 	/*Y0-Y7*/	"","","","","","","","",
-	/*Z0-Z7*/	"","","","","","","","",
-	/*AA0-AA7*/	"","","","","","","","",
-	/*AB0-AB7*/	"","","","","","","","",
-	/*AC0-AC7*/	"","","","","","","","";
+	/*Z0-Z7*/	"","","","","","","","";

 	pin_mclr_vpp {
 		gpio-hog;
--- a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
@@ -127,10 +127,7 @@
 	/*W0-W7*/	"","","","","","","","",
 	/*X0-X7*/	"","","","","","","","",
 	/*Y0-Y7*/	"","","","","","","","",
-	/*Z0-Z7*/	"","","","","","","","",
-	/*AA0-AA7*/	"","","","","","","","",
-	/*AB0-AB7*/	"","","","","","","","",
-	/*AC0-AC7*/	"","","","","","","","";
+	/*Z0-Z7*/	"","","","","","","","";
 };

 &fmc {
@@ -180,6 +177,7 @@

 &emmc {
 	status = "okay";
+	clk-phase-mmc-hs200 = <36>, <270>;
 };

 &fsim0 {
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -460,7 +460,7 @@
 			status = "disabled";
 		};

-		nand: nand@18046000 {
+		nand_controller: nand-controller@18046000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
 			      <0x18046f00 0x20>;
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/bcm-hr2.dtsi
@@ -179,7 +179,7 @@
 			status = "disabled";
 		};

-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x26000 0x600>,
 			      <0x11b408 0x600>,
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -269,7 +269,7 @@
 			dma-coherent;
 		};

-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x026000 0x600>,
 			      <0x11b408 0x600>,
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -28,11 +28,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -395,7 +395,7 @@
 		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
 		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;

-		emmc2: emmc2@7e340000 {
+		emmc2: mmc@7e340000 {
 			compatible = "brcm,bcm2711-emmc2";
 			reg = <0x0 0x7e340000 0x100>;
 			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -14,11 +14,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -14,7 +14,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -15,11 +15,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -15,7 +15,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -15,7 +15,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
@@ -5,7 +5,7 @@

 / {
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@@ -23,7 +23,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@@ -18,7 +18,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -4,7 +4,7 @@
 	leds {
 		compatible = "gpio-leds";

-		act {
+		led-act {
 			label = "ACT";
 			default-state = "keep";
 			linux,default-trigger = "heartbeat";
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -15,11 +15,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@@ -19,11 +19,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -20,11 +20,11 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};

-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -20,7 +20,7 @@
 	};

 	leds {
-		act {
+		led-act {
 			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
@@ -14,7 +14,7 @@
 		 * Since there is no upstream GPIO driver yet,
 		 * remove the incomplete node.
 		 */
-		/delete-node/ act;
+		/delete-node/ led-act;
 	};

 	reg_3v3: fixed-regulator {
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -420,7 +420,7 @@
 			status = "disabled";
 		};

-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
--- a/arch/arm/boot/dts/bcm63138.dtsi
+++ b/arch/arm/boot/dts/bcm63138.dtsi
@@ -203,7 +203,7 @@
 			status = "disabled";
 		};

-		nand: nand@2000 {
+		nand_controller: nand-controller@2000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.0", "brcm,brcmnand";
--- a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
+++ b/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
@@ -14,10 +14,10 @@
 	};
 };

-&nand {
+&nand_controller {
 	status = "okay";

-	nandcs@1 {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <1>;
 		nand-ecc-step-size = <512>;
--- a/arch/arm/boot/dts/bcm7445.dtsi
+++ b/arch/arm/boot/dts/bcm7445.dtsi
@@ -148,7 +148,7 @@
 			reg-names = "aon-ctrl", "aon-sram";
 		};

-		nand: nand@3e2800 {
+		nand_controller: nand-controller@3e2800 {
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -82,8 +82,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -60,8 +60,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -68,8 +68,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -74,8 +74,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -74,8 +74,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -90,8 +90,8 @@
 	};
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -78,8 +78,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -78,8 +78,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -89,8 +89,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -68,8 +68,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/bcm963138dvt.dts
+++ b/arch/arm/boot/dts/bcm963138dvt.dts
@@ -31,10 +31,10 @@
 	status = "okay";
 };

-&nand {
+&nand_controller {
 	status = "okay";

-	nandcs@0 {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-ecc-strength = <4>;
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -74,8 +74,8 @@
 	status = "okay";
 };

-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -351,7 +351,7 @@
 			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <12>;
-			mbox_dsp: mbox_dsp {
+			mbox_dsp: mbox-dsp {
 				ti,mbox-tx = <3 0 0>;
 				ti,mbox-rx = <0 0 0>;
 			};
--- a/arch/arm/boot/dts/dra7-ipu-dsp-common.dtsi
+++ b/arch/arm/boot/dts/dra7-ipu-dsp-common.dtsi
@@ -5,17 +5,17 @@

 &mailbox5 {
 	status = "okay";
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
 		status = "okay";
 	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
 		status = "okay";
 	};
 };

 &mailbox6 {
 	status = "okay";
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
 		status = "okay";
 	};
 };
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/dra7-l4.dtsi
@@ -1315,7 +1315,7 @@
 			};
 		};

-		target-module@55000 {			/* 0x48055000, ap 13 0e.0 */
+		gpio2_target: target-module@55000 {		/* 0x48055000, ap 13 0e.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x55000 0x4>,
 			      <0x55010 0x4>,
@@ -1348,7 +1348,7 @@
 			};
 		};

-		target-module@57000 {			/* 0x48057000, ap 15 06.0 */
+		gpio3_target: target-module@57000 {		/* 0x48057000, ap 15 06.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x57000 0x4>,
 			      <0x57010 0x4>,
--- a/arch/arm/boot/dts/dra72x.dtsi
+++ b/arch/arm/boot/dts/dra72x.dtsi
@@ -77,12 +77,12 @@
 };

 &mailbox5 {
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
 		ti,mbox-tx = <6 2 2>;
 		ti,mbox-rx = <4 2 2>;
 		status = "disabled";
 	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
 		ti,mbox-tx = <5 2 2>;
 		ti,mbox-rx = <1 2 2>;
 		status = "disabled";
@@ -90,7 +90,7 @@
 };

 &mailbox6 {
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
 		ti,mbox-tx = <6 2 2>;
 		ti,mbox-rx = <4 2 2>;
 		status = "disabled";
--- a/arch/arm/boot/dts/dra74-ipu-dsp-common.dtsi
+++ b/arch/arm/boot/dts/dra74-ipu-dsp-common.dtsi
@@ -6,7 +6,7 @@
 #include "dra7-ipu-dsp-common.dtsi"

 &mailbox6 {
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
 		status = "okay";
 	};
 };
--- a/arch/arm/boot/dts/dra74x.dtsi
+++ b/arch/arm/boot/dts/dra74x.dtsi
@@ -145,12 +145,12 @@
 };

 &mailbox5 {
-	mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
+	mbox_ipu1_ipc3x: mbox-ipu1-ipc3x {
 		ti,mbox-tx = <6 2 2>;
 		ti,mbox-rx = <4 2 2>;
 		status = "disabled";
 	};
-	mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
+	mbox_dsp1_ipc3x: mbox-dsp1-ipc3x {
 		ti,mbox-tx = <5 2 2>;
 		ti,mbox-rx = <1 2 2>;
 		status = "disabled";
@@ -158,12 +158,12 @@
 };

 &mailbox6 {
-	mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
+	mbox_ipu2_ipc3x: mbox-ipu2-ipc3x {
 		ti,mbox-tx = <6 2 2>;
 		ti,mbox-rx = <4 2 2>;
 		status = "disabled";
 	};
-	mbox_dsp2_ipc3x: mbox_dsp2_ipc3x {
+	mbox_dsp2_ipc3x: mbox-dsp2-ipc3x {
 		ti,mbox-tx = <5 2 2>;
 		ti,mbox-rx = <1 2 2>;
 		status = "disabled";
--- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts
+++ b/arch/arm/boot/dts/gemini-dlink-dns-313.dts
@@ -140,7 +140,7 @@
 		};
 	};

-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		/* Uses MDC and MDIO */
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -62,7 +62,7 @@
 		};
 	};

-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
--- a/arch/arm/boot/dts/gemini-rut1xx.dts
+++ b/arch/arm/boot/dts/gemini-rut1xx.dts
@@ -56,7 +56,7 @@
 		};
 	};

-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini-wbd111.dts
@@ -68,7 +68,7 @@
 		};
 	};

-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini-wbd222.dts
@@ -67,7 +67,7 @@
 		};
 	};

-	mdio0: ethernet-phy {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
 			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
--- a/arch/arm/boot/dts/gemini.dtsi
+++ b/arch/arm/boot/dts/gemini.dtsi
@@ -286,6 +286,7 @@
 			clock-names = "PCLK", "PCICLK";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pci_default_pins>;
+			device_type = "pci";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			#interrupt-cells = <1>;
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -106,6 +106,8 @@
 			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -315,8 +315,8 @@
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
 			>;
 		};

@@ -403,6 +403,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
 	status = "disabled";
 };

--- a/arch/arm/boot/dts/omap4-l4.dtsi
+++ b/arch/arm/boot/dts/omap4-l4.dtsi
@@ -597,11 +597,11 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <3>;
 				ti,mbox-num-fifos = <8>;
-				mbox_ipu: mbox_ipu {
+				mbox_ipu: mbox-ipu {
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <1 0 0>;
 				};
-				mbox_dsp: mbox_dsp {
+				mbox_dsp: mbox-dsp {
 					ti,mbox-tx = <3 0 0>;
 					ti,mbox-rx = <2 0 0>;
 				};
--- a/arch/arm/boot/dts/omap5-l4.dtsi
+++ b/arch/arm/boot/dts/omap5-l4.dtsi
@@ -613,11 +613,11 @@
 				#mbox-cells = <1>;
 				ti,mbox-num-users = <3>;
 				ti,mbox-num-fifos = <8>;
-				mbox_ipu: mbox_ipu {
+				mbox_ipu: mbox-ipu {
 					ti,mbox-tx = <0 0 0>;
 					ti,mbox-rx = <1 0 0>;
 				};
-				mbox_dsp: mbox_dsp {
+				mbox_dsp: mbox-dsp {
 					ti,mbox-tx = <3 0 0>;
 					ti,mbox-rx = <2 0 0>;
 				};
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rk3036-kylin.dts
@@ -390,7 +390,7 @@
 		};
 	};

-	sleep {
+	suspend {
 		global_pwroff: global-pwroff {
 			rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
 		};
--- a/arch/arm/boot/dts/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rk3066a.dtsi
@@ -755,7 +755,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;

-		pd_vio@RK3066_PD_VIO {
+		power-domain@RK3066_PD_VIO {
 			reg = <RK3066_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -782,7 +782,7 @@
 				 <&qos_rga>;
 		};

-		pd_video@RK3066_PD_VIDEO {
+		power-domain@RK3066_PD_VIDEO {
 			reg = <RK3066_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -791,7 +791,7 @@
 			pm_qos = <&qos_vpu>;
 		};

-		pd_gpu@RK3066_PD_GPU {
+		power-domain@RK3066_PD_GPU {
 			reg = <RK3066_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -150,16 +150,16 @@
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x2000e000 0x20>;
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER3>, <&cru PCLK_TIMER3>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER3>, <&cru SCLK_TIMER3>;
+		clock-names = "pclk", "timer";
 	};

 	timer6: timer@200380a0 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x200380a0 0x20>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER6>, <&cru PCLK_TIMER0>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER6>;
+		clock-names = "pclk", "timer";
 	};

 	i2s0: i2s@1011a000 {
@@ -699,7 +699,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;

-		pd_vio@RK3188_PD_VIO {
+		power-domain@RK3188_PD_VIO {
 			reg = <RK3188_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -721,7 +721,7 @@
 				 <&qos_rga>;
 		};

-		pd_video@RK3188_PD_VIDEO {
+		power-domain@RK3188_PD_VIDEO {
 			reg = <RK3188_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -730,7 +730,7 @@
 			pm_qos = <&qos_vpu>;
 		};

-		pd_gpu@RK3188_PD_GPU {
+		power-domain@RK3188_PD_GPU {
 			reg = <RK3188_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -524,7 +524,7 @@
 		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
 		pinctrl-2 = <&otp_pin>;
-		#thermal-sensor-cells = <0>;
+		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
 	};
@@ -565,10 +565,9 @@
 		compatible = "rockchip,iommu";
 		reg = <0x20020800 0x100>;
 		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};

@@ -576,10 +575,9 @@
 		compatible = "rockchip,iommu";
 		reg = <0x20030480 0x40>, <0x200304c0 0x40>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vdec_mmu";
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};

@@ -609,7 +607,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x20053f00 0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -630,10 +627,9 @@
 		compatible = "rockchip,iommu";
 		reg = <0x20070800 0x100>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};

--- a/arch/arm/boot/dts/rk3288-rock2-som.dtsi
+++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
@@ -218,7 +218,7 @@
 	flash0-supply = <&vcc_flash>;
 	flash1-supply = <&vccio_pmu>;
 	gpio30-supply = <&vccio_pmu>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
--- a/arch/arm/boot/dts/rk3288-vyasa.dts
+++ b/arch/arm/boot/dts/rk3288-vyasa.dts
@@ -379,10 +379,10 @@
 	audio-supply = <&vcc_18>;
 	bb-supply = <&vcc_io>;
 	dvp-supply = <&vcc_io>;
-	flash0-suuply = <&vcc_18>;
+	flash0-supply = <&vcc_18>;
 	flash1-supply = <&vcc_lan>;
 	gpio30-supply = <&vcc_io>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -240,8 +240,8 @@
 		compatible = "rockchip,rk3288-timer";
 		reg = <0x0 0xff810000 0x0 0x20>;
 		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};

 	display-subsystem {
@@ -788,7 +788,7 @@
 			 *	*_HDMI		HDMI
 			 *	*_MIPI_*	MIPI
 			 */
-			pd_vio@RK3288_PD_VIO {
+			power-domain@RK3288_PD_VIO {
 				reg = <RK3288_PD_VIO>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru ACLK_ISP>,
@@ -830,7 +830,7 @@
 			 * Note: The following 3 are HEVC(H.265) clocks,
 			 * and on the ACLK_HEVC_NIU (NOC).
 			 */
-			pd_hevc@RK3288_PD_HEVC {
+			power-domain@RK3288_PD_HEVC {
 				reg = <RK3288_PD_HEVC>;
 				clocks = <&cru ACLK_HEVC>,
 					 <&cru SCLK_HEVC_CABAC>,
@@ -844,7 +844,7 @@
 			 * (video endecoder & decoder) clocks that on the
 			 * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
 			 */
-			pd_video@RK3288_PD_VIDEO {
+			power-domain@RK3288_PD_VIDEO {
 				reg = <RK3288_PD_VIDEO>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
@@ -855,7 +855,7 @@
 			 * Note: ACLK_GPU is the GPU clock,
 			 * and on the ACLK_GPU_NIU (NOC).
 			 */
-			pd_gpu@RK3288_PD_GPU {
+			power-domain@RK3288_PD_GPU {
 				reg = <RK3288_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu_r>,
@@ -1593,7 +1593,7 @@
 			drive-strength = <12>;
 		};

-		sleep {
+		suspend {
 			global_pwroff: global-pwroff {
 				rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>;
 			};
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -34,7 +34,7 @@
 					#clock-cells = <1>;
 				};

-				ab8500_gpio: ab8500-gpio {
+				ab8500_gpio: ab8500-gpiocontroller {
 					compatible = "stericsson,ab8500-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
@@ -42,15 +42,15 @@

 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};

 				gpadc: ab8500-gpadc {
 					compatible = "stericsson,ab8500-gpadc";
-					interrupts = <32 IRQ_TYPE_LEVEL_HIGH
-						      39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
+						     <39 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "HW_CONV_END", "SW_CONV_END";
 					vddadc-supply = <&ab8500_ldo_tvout_reg>;
 					#address-cells = <1>;
@@ -169,13 +169,13 @@

 				ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -192,8 +192,8 @@

 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};

--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -30,7 +30,7 @@
 					#clock-cells = <1>;
 				};

-				ab8505_gpio: ab8505-gpio {
+				ab8505_gpio: ab8505-gpiocontroller {
 					compatible = "stericsson,ab8505-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
@@ -38,8 +38,8 @@

 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};

@@ -131,13 +131,13 @@

 				ab8500_usb: ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -154,8 +154,8 @@

 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};

--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi
@@ -9,7 +9,7 @@
 	soc {
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/* Hog a few default settings */
 					pinctrl-names = "default";
 					pinctrl-0 = <&gpio2_default_mode>,
--- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
@@ -19,6 +19,9 @@
 					     <19 IRQ_TYPE_EDGE_RISING>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
 			};
 			magnetometer@1e {
 				compatible = "st,lsm303dlm-magn";
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -224,7 +224,7 @@

 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 				};

 				ab8500_usb {
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -376,7 +376,7 @@

 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/*
 					 * AB8500 GPIOs are numbered starting from 1, so the first
 					 * index 0 is what in the datasheet is called "GPIO1", and
--- a/arch/arm/boot/dts/stm32429i-eval.dts
+++ b/arch/arm/boot/dts/stm32429i-eval.dts
@@ -119,17 +119,15 @@
 		};
 	};

-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 0>;
 		};
-		button@1 {
+		button-1 {
 			label = "Tamper";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioc 13 0>;
--- a/arch/arm/boot/dts/stm32746g-eval.dts
+++ b/arch/arm/boot/dts/stm32746g-eval.dts
@@ -81,12 +81,10 @@
 		};
 	};

-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioc 13 0>;
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -81,12 +81,10 @@
 		};
 	};

-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 0>;
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -283,8 +283,6 @@
 		};

 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>;
@@ -299,8 +297,6 @@
 		};

 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>;
@@ -633,8 +629,6 @@
 		};

 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>;
@@ -649,8 +643,6 @@
 		};

 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>;
@@ -709,7 +701,7 @@
 			status = "disabled";
 		};

-		rcc: rcc@40023810 {
+		rcc: rcc@40023800 {
 			#reset-cells = <1>;
 			#clock-cells = <2>;
 			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -104,12 +104,10 @@
 		};
 	};

-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -265,8 +265,6 @@
 		};

 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>;
@@ -281,8 +279,6 @@
 		};

 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>;
@@ -364,9 +360,9 @@
 			status = "disabled";
 		};

-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
-			reg = <0x40005C00 0x400>;
+			reg = <0x40005c00 0x400>;
 			interrupts = <72>,
 				     <73>;
 			resets = <&rcc STM32F7_APB1_RESET(I2C3)>;
@@ -531,8 +527,6 @@
 		};

 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>;
@@ -547,8 +541,6 @@
 		};

 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>;
--- a/arch/arm/boot/dts/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/stm32f769-disco.dts
@@ -75,12 +75,10 @@
 		};
 	};

-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -454,8 +454,6 @@
 		};

 		lptimer4: timer@58002c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58002c00 0x400>;
 			clocks = <&rcc LPTIM4_CK>;
@@ -470,8 +468,6 @@
 		};

 		lptimer5: timer@58003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58003000 0x400>;
 			clocks = <&rcc LPTIM5_CK>;
--- a/arch/arm/boot/dts/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/stm32mp151.dtsi
@@ -1395,12 +1395,6 @@
 			status = "disabled";
 		};

-		stmmac_axi_config_0: stmmac-axi-config {
-			snps,wr_osr_lmt = <0x7>;
-			snps,rd_osr_lmt = <0x7>;
-			snps,blen = <0 0 0 0 16 8 4>;
-		};
-
 		ethernet0: ethernet@5800a000 {
 			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
 			reg = <0x5800a000 0x2000>;
@@ -1424,6 +1418,12 @@
 			snps,axi-config = <&stmmac_axi_config_0>;
 			snps,tso;
 			status = "disabled";
+
+			stmmac_axi_config_0: stmmac-axi-config {
+				snps,wr_osr_lmt = <0x7>;
+				snps,rd_osr_lmt = <0x7>;
+				snps,blen = <0 0 0 0 16 8 4>;
+			};
 		};

 		usbh_ohci: usbh-ohci@5800c000 {
--- a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
@@ -184,8 +184,6 @@

 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};

@@ -208,7 +206,6 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};

 			bst_out: boost {
@@ -219,13 +216,13 @@
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};

 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};

--- a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -173,8 +173,6 @@

 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};

@@ -197,7 +195,6 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};

 			 bst_out: boost {
@@ -213,7 +210,7 @@
 			 vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			 };
 		};

@@ -269,7 +266,7 @@
 	st,neg-edge;
 	bus-width = <8>;
 	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
 	mmc-ddr-3_3v;
 	status = "okay";
 };
--- a/arch/arm/boot/dts/stm32mp157c-odyssey.dts
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -64,7 +64,7 @@
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	disable-wp;
 	st,neg-edge;
 	bus-width = <4>;
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -34,7 +34,6 @@

 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#size-cells = <0>;
 		poll-interval = <20>;

 		/*
@@ -60,7 +59,6 @@

 	gpio-keys {
 		compatible = "gpio-keys";
-		#size-cells = <0>;

 		button-1 {
 			label = "TA2-GPIO-B";
@@ -184,12 +182,11 @@

 	};

-	polytouch@38 {
-		compatible = "edt,edt-ft5x06";
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
 		reg = <0x38>;
 		interrupt-parent = <&gpiog>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-		linux,wakeup;
 	};
 };

--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -234,8 +234,6 @@

 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};

@@ -257,7 +255,6 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};

 			bst_out: boost {
@@ -273,7 +270,7 @@
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};

@@ -338,7 +335,7 @@
 	#size-cells = <0>;
 	status = "okay";

-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -194,7 +194,7 @@
 	#size-cells = <0>;
 	status = "okay";

-	flash0: spi-flash@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
--- a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
@@ -146,8 +146,6 @@

 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};

@@ -171,7 +169,6 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};

 			bst_out: boost {
@@ -182,13 +179,13 @@
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};

 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};

--- a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
+++ b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
@@ -1009,7 +1009,7 @@
 		nvidia,audio-codec = <&wm8903>;

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
 		nvidia,int-mic-en-gpios = <&wm8903 1 GPIO_ACTIVE_HIGH>;
 		nvidia,headset;

--- a/arch/arm/boot/dts/tegra20-harmony.dts
+++ b/arch/arm/boot/dts/tegra20-harmony.dts
@@ -748,7 +748,7 @@

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;
 		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(X, 0)
 			GPIO_ACTIVE_HIGH>;
 		nvidia,ext-mic-en-gpios = <&gpio TEGRA_GPIO(X, 1)
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -84,7 +84,7 @@
 		nvidia,audio-codec = <&wm8903>;

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;

 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/tegra20-plutux.dts
@@ -52,7 +52,7 @@
 		nvidia,audio-codec = <&wm8903>;

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;

 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
--- a/arch/arm/boot/dts/tegra20-seaboard.dts
+++ b/arch/arm/boot/dts/tegra20-seaboard.dts
@@ -911,7 +911,7 @@
 		nvidia,audio-codec = <&wm8903>;

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_LOW>;

 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/tegra20-tec.dts
@@ -61,7 +61,7 @@

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;

 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
--- a/arch/arm/boot/dts/tegra20-ventana.dts
+++ b/arch/arm/boot/dts/tegra20-ventana.dts
@@ -686,7 +686,7 @@
 		nvidia,audio-codec = <&wm8903>;

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
 		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(X, 0)
 			GPIO_ACTIVE_HIGH>;
 		nvidia,ext-mic-en-gpios = <&gpio TEGRA_GPIO(X, 1)
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
@@ -143,7 +143,7 @@
 	};

 	vdd_3v3_sys: regulator@1 {
-		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
 };
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -589,7 +589,7 @@

 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
-			GPIO_ACTIVE_HIGH>;
+			GPIO_ACTIVE_LOW>;

 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
--- a/Show More
+++ b/Show More