arm: at91: move board header to arch/arm/mach-at91

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

arch/arm/mach-at91/gsia18s.h

@@ -0,0 +1,33 @@
+/* Buttons */
+#define GPIO_TRIG_NET_IN		AT91_PIN_PB21
+#define GPIO_CARD_UNMOUNT_0		AT91_PIN_PB13
+#define GPIO_CARD_UNMOUNT_1		AT91_PIN_PB12
+#define GPIO_KEY_POWER			AT91_PIN_PA25
+
+/* PCF8574 0x20 GPIO - U1 on the GS_IA18-CB_V3 board */
+#define GS_IA18_S_PCF_GPIO_BASE0	NR_BUILTIN_GPIO
+#define PCF_GPIO_HDC_POWER		(GS_IA18_S_PCF_GPIO_BASE0 + 0)
+#define PCF_GPIO_WIFI_SETUP		(GS_IA18_S_PCF_GPIO_BASE0 + 1)
+#define PCF_GPIO_WIFI_ENABLE		(GS_IA18_S_PCF_GPIO_BASE0 + 2)
+#define PCF_GPIO_WIFI_RESET		(GS_IA18_S_PCF_GPIO_BASE0 + 3)
+#define PCF_GPIO_ETH_DETECT		4 /* this is a GPI */
+#define PCF_GPIO_GPS_SETUP		(GS_IA18_S_PCF_GPIO_BASE0 + 5)
+#define PCF_GPIO_GPS_STANDBY		(GS_IA18_S_PCF_GPIO_BASE0 + 6)
+#define PCF_GPIO_GPS_POWER		(GS_IA18_S_PCF_GPIO_BASE0 + 7)
+
+/* PCF8574 0x22 GPIO - U1 on the GS_2G_OPT1-A_V0 board (Alarm) */
+#define GS_IA18_S_PCF_GPIO_BASE1	(GS_IA18_S_PCF_GPIO_BASE0 + 8)
+#define PCF_GPIO_ALARM1			(GS_IA18_S_PCF_GPIO_BASE1 + 0)
+#define PCF_GPIO_ALARM2			(GS_IA18_S_PCF_GPIO_BASE1 + 1)
+#define PCF_GPIO_ALARM3			(GS_IA18_S_PCF_GPIO_BASE1 + 2)
+#define PCF_GPIO_ALARM4			(GS_IA18_S_PCF_GPIO_BASE1 + 3)
+/* bits 4, 5, 6 not used */
+#define PCF_GPIO_ALARM_V_RELAY_ON	(GS_IA18_S_PCF_GPIO_BASE1 + 7)
+
+/* PCF8574 0x24 GPIO U1 on the GS_2G-OPT23-A_V0 board (Modem) */
+#define GS_IA18_S_PCF_GPIO_BASE2	(GS_IA18_S_PCF_GPIO_BASE1 + 8)
+#define PCF_GPIO_MODEM_POWER		(GS_IA18_S_PCF_GPIO_BASE2 + 0)
+#define PCF_GPIO_MODEM_RESET		(GS_IA18_S_PCF_GPIO_BASE2 + 3)
+/* bits 1, 2, 4, 5 not used */
+#define PCF_GPIO_TRX_RESET		(GS_IA18_S_PCF_GPIO_BASE2 + 6)
+/* bit 7 not used */