xiaomi-sm8450/android_kernel_xiaomi_sm8450
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Browse Source 
Pull ARM SoC driver updates from Arnd Bergmann:
 "Driver updates for ARM SoCs, including a couple of newly added
  drivers:

   - A new driver for the power management controller on TI Keystone

   - Support for the prerelease "SCPI" firmware protocol that ended up
     being shipped by Amlogic in their GXBB SoC.

   - A soc_device can now be matched using a glob from inside the
     kernel, when another driver wants to know the specific chip it is
     running on and cannot find out from DT, firmware or hardware.

   - Renesas SoCs now support identification through the soc_device
     interface, both in user space and kernel.

   - Renesas r8a7743 and r8a7745 gain support for their system
     controller

   - A new checking module for the ARM "PSCI" (not to be confused with
     "SCPI" mentioned above) firmware interface.

   - A new driver for the Tegra GMI memory interface

   - Support for the Tegra firmware interfaces with their power
     management controllers

  As usual, the updates for the reset controller framework are merged
  here, as they tend to touch multiple SoCs as well, including a new
  driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
  interface.

  The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
  Rockchips SoCs see some further updates"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
  misc: sram: remove useless #ifdef
  drivers: psci: Allow PSCI node to be disabled
  drivers: psci: PSCI checker module
  soc: renesas: Identify SoC and register with the SoC bus
  firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
  firmware: qcom: scm: Remove core, iface and bus clocks dependency
  dt-bindings: firmware: scm: Add MSM8996 DT bindings
  memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
  bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
  ARM: shmobile: Document DT bindings for Product Register
  soc: renesas: rcar-sysc: add R8A7745 support
  reset: Add Tegra BPMP reset driver
  dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
  dt-bindings: Add power domains to Tegra BPMP firmware
  firmware: tegra: Add BPMP support
  firmware: tegra: Add IVC library
  dt-bindings: firmware: Add bindings for Tegra BPMP
  mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
  mailbox: Add Tegra HSP driver
  firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
  ...
This commit is contained in:
Linus Torvalds
2016-12-15 16:03:25 -08:00
parent 482c3e8835 2ada959322
commit 991688bfc6
86 changed files with 11443 additions and 737 deletions
Download Patch File Download Diff File Expand all files Collapse all files

20
Documentation/devicetree/bindings/arm/amlogic,scpi.txt Normal file
View File

@@ -0,0 +1,20 @@
System Control and Power Interface (SCPI) Message Protocol
(in addition to the standard binding in [0])
----------------------------------------------------------
Required properties
- compatible : should be "amlogic,meson-gxbb-scpi"
AMLOGIC SRAM and Shared Memory for SCPI
------------------------------------
Required properties:
- compatible : should be "amlogic,meson-gxbb-sram"
Each sub-node represents the reserved area for SCPI.
Required sub-node properties:
- compatible : should be "amlogic,meson-gxbb-scp-shmem" for SRAM based shared
memory on Amlogic GXBB SoC.
[0] Documentation/devicetree/bindings/arm/arm,scpi.txt

25
Documentation/devicetree/bindings/arm/arm,scpi.txt
View File

@@ -7,7 +7,10 @@ by Linux to initiate various system control and power operations.
Required properties:
- compatible : should be "arm,scpi"
- compatible : should be
* "arm,scpi" : For implementations complying to SCPI v1.0 or above
* "arm,scpi-pre-1.0" : For implementations complying to all
unversioned releases prior to SCPI v1.0
- mboxes: List of phandle and mailbox channel specifiers
All the channels reserved by remote SCP firmware for use by
SCPI message protocol should be specified in any order
@@ -59,18 +62,14 @@ SRAM and Shared Memory for SCPI
A small area of SRAM is reserved for SCPI communication between application
processors and SCP.
Required properties:
- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno
The rest of the properties should follow the generic mmio-sram description
found in ../../sram/sram.txt
The properties should follow the generic mmio-sram description found in [3]
Each sub-node represents the reserved area for SCPI.
Required sub-node properties:
- reg : The base offset and size of the reserved area with the SRAM
- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based
shared memory on Juno platforms
- compatible : should be "arm,scp-shmem" for Non-secure SRAM based
shared memory
Sensor bindings for the sensors based on SCPI Message Protocol
--------------------------------------------------------------
@@ -81,11 +80,9 @@ Required properties:
- #thermal-sensor-cells: should be set to 1. This property follows the
thermal device tree bindings[2].
Valid cell values are raw identifiers (Sensor
ID) as used by the firmware. Refer to
platform documentation for your
implementation for the IDs to use. For Juno
R0 and Juno R1 refer to [3].
Valid cell values are raw identifiers (Sensor ID)
as used by the firmware. Refer to platform details
for your implementation for the IDs to use.
Power domain bindings for the power domains based on SCPI Message Protocol
------------------------------------------------------------
@@ -112,7 +109,7 @@ Required properties:
[0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/thermal/thermal.txt
[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
[3] Documentation/devicetree/bindings/sram/sram.txt
[4] Documentation/devicetree/bindings/power/power_domain.txt
Example:

16
Documentation/devicetree/bindings/arm/atmel-at91.txt
View File

@@ -225,3 +225,19 @@ required properties:
compatible = "atmel,sama5d3-sfr", "syscon";
reg = <0xf0038000 0x60>;
};
Security Module (SECUMOD)
The Security Module macrocell provides all necessary secure functions to avoid
voltage, temperature, frequency and mechanical attacks on the chip. It also
embeds secure memories that can be scrambled
required properties:
- compatible: Should be "atmel,<chip>-secumod", "syscon".
<chip> can be "sama5d2".
- reg: Should contain registers location and length
secumod@fc040000 {
compatible = "atmel,sama5d2-secumod", "syscon";
reg = <0xfc040000 0x100>;
};

26
Documentation/devicetree/bindings/arm/juno,scpi.txt Normal file
View File

@@ -0,0 +1,26 @@
System Control and Power Interface (SCPI) Message Protocol
(in addition to the standard binding in [0])
Juno SRAM and Shared Memory for SCPI
------------------------------------
Required properties:
- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM
Each sub-node represents the reserved area for SCPI.
Required sub-node properties:
- reg : The base offset and size of the reserved area with the SRAM
- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based
shared memory on Juno platforms
Sensor bindings for the sensors based on SCPI Message Protocol
--------------------------------------------------------------
Required properties:
- compatible : should be "arm,scpi-sensors".
- #thermal-sensor-cells: should be set to 1.
For Juno R0 and Juno R1 refer to [1] for the
sensor identifiers
[0] Documentation/devicetree/bindings/arm/arm,scpi.txt
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html

81
Documentation/devicetree/bindings/arm/keystone/ti,sci.txt Normal file
View File

@@ -0,0 +1,81 @@
Texas Instruments System Control Interface (TI-SCI) Message Protocol
--------------------------------------------------------------------
Texas Instrument's processors including those belonging to Keystone generation
of processors have separate hardware entity which is now responsible for the
management of the System on Chip (SoC) system. These include various system
level functions as well.
An example of such an SoC is K2G, which contains the system control hardware
block called Power Management Micro Controller (PMMC). This hardware block is
initialized early into boot process and provides services to Operating Systems
on multiple processors including ones running Linux.
See http://processors.wiki.ti.com/index.php/TISCI for protocol definition.
TI-SCI controller Device Node:
=============================
The TI-SCI node describes the Texas Instrument's System Controller entity node.
This parent node may optionally have additional children nodes which describe
specific functionality such as clocks, power domain, reset or additional
functionality as may be required for the SoC. This hierarchy also describes the
relationship between the TI-SCI parent node to the child node.
Required properties:
-------------------
- compatible: should be "ti,k2g-sci"
- mbox-names:
"rx" - Mailbox corresponding to receive path
"tx" - Mailbox corresponding to transmit path
- mboxes: Mailboxes corresponding to the mbox-names. Each value of the mboxes
property should contain a phandle to the mailbox controller device
node and an args specifier that will be the phandle to the intended
sub-mailbox child node to be used for communication.
See Documentation/devicetree/bindings/mailbox/mailbox.txt for more details
about the generic mailbox controller and client driver bindings. Also see
Documentation/devicetree/bindings/mailbox/ti,message-manager.txt for typical
controller that is used to communicate with this System controllers.
Optional Properties:
-------------------
- reg-names:
debug_messages - Map the Debug message region
- reg: register space corresponding to the debug_messages
- ti,system-reboot-controller: If system reboot can be triggered by SoC reboot
Example (K2G):
-------------
pmmc: pmmc {
compatible = "ti,k2g-sci";
mbox-names = "rx", "tx";
mboxes= <&msgmgr &msgmgr_proxy_pmmc_rx>,
<&msgmgr &msgmgr_proxy_pmmc_tx>;
reg-names = "debug_messages";
reg = <0x02921800 0x800>;
};
TI-SCI Client Device Node:
=========================
Client nodes are maintained as children of the relevant TI-SCI device node.
Example (K2G):
-------------
pmmc: pmmc {
compatible = "ti,k2g-sci";
...
my_clk_node: clk_node {
...
...
};
my_pd_node: pd_node {
...
...
};
};

18
Documentation/devicetree/bindings/arm/shmobile.txt
View File

@@ -85,3 +85,21 @@ Boards:
compatible = "renesas,sk-rzg1m", "renesas,r8a7743"
- Wheat
compatible = "renesas,wheat", "renesas,r8a7792"
Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC
product and revision information. If present, a device node for this register
should be added.
Required properties:
- compatible: Must be "renesas,prr".
- reg: Base address and length of the register block.
Examples
--------
prr: chipid@ff000044 {
compatible = "renesas,prr";
reg = <0 0xff000044 0 4>;
};

132
Documentation/devicetree/bindings/bus/nvidia,tegra20-gmi.txt Normal file
View File

@@ -0,0 +1,132 @@
Device tree bindings for NVIDIA Tegra Generic Memory Interface bus
The Generic Memory Interface bus enables memory transfers between internal and
external memory. Can be used to attach various high speed devices such as
synchronous/asynchronous NOR, FPGA, UARTS and more.
The actual devices are instantiated from the child nodes of a GMI node.
Required properties:
- compatible : Should contain one of the following:
For Tegra20 must contain "nvidia,tegra20-gmi".
For Tegra30 must contain "nvidia,tegra30-gmi".
- reg: Should contain GMI controller registers location and length.
- clocks: Must contain an entry for each entry in clock-names.
- clock-names: Must include the following entries: "gmi"
- resets : Must contain an entry for each entry in reset-names.
- reset-names : Must include the following entries: "gmi"
- #address-cells: The number of cells used to represent physical base
addresses in the GMI address space. Should be 2.
- #size-cells: The number of cells used to represent the size of an address
range in the GMI address space. Should be 1.
- ranges: Must be set up to reflect the memory layout with three integer values
for each chip-select line in use (only one entry is supported, see below
comments):
<cs-number> <offset> <physical address of mapping> <size>
Note that the GMI controller does not have any internal chip-select address
decoding, because of that chip-selects either need to be managed via software
or by employing external chip-select decoding logic.
If external chip-select logic is used to support multiple devices it is assumed
that the devices use the same timing and so are probably the same type. It also
assumes that they can fit in the 256MB address range. In this case only one
child device is supported which represents the active chip-select line, see
examples for more insight.
The chip-select number is decoded from the child nodes second address cell of
'ranges' property, if 'ranges' property is not present or empty chip-select will
then be decoded from the first cell of the 'reg' property.
Optional child cs node properties:
- nvidia,snor-data-width-32bit: Use 32bit data-bus, default is 16bit.
- nvidia,snor-mux-mode: Enable address/data MUX mode.
- nvidia,snor-rdy-active-before-data: Assert RDY signal one cycle before data.
If omitted it will be asserted with data.
- nvidia,snor-rdy-active-high: RDY signal is active high
- nvidia,snor-adv-active-high: ADV signal is active high
- nvidia,snor-oe-active-high: WE/OE signal is active high
- nvidia,snor-cs-active-high: CS signal is active high
Note that there is some special handling for the timing values.
From Tegra TRM:
Programming 0 means 1 clock cycle: actual cycle = programmed cycle + 1
- nvidia,snor-muxed-width: Number of cycles MUX address/data asserted on the
bus. Valid values are 0-15, default is 1
- nvidia,snor-hold-width: Number of cycles CE stays asserted after the
de-assertion of WR_N (in case of SLAVE/MASTER Request) or OE_N
(in case of MASTER Request). Valid values are 0-15, default is 1
- nvidia,snor-adv-width: Number of cycles during which ADV stays asserted.
Valid values are 0-15, default is 1.
- nvidia,snor-ce-width: Number of cycles before CE is asserted.
Valid values are 0-15, default is 4
- nvidia,snor-we-width: Number of cycles during which WE stays asserted.
Valid values are 0-15, default is 1
- nvidia,snor-oe-width: Number of cycles during which OE stays asserted.
Valid values are 0-255, default is 1
- nvidia,snor-wait-width: Number of cycles before READY is asserted.
Valid values are 0-255, default is 3
Example with two SJA1000 CAN controllers connected to the GMI bus. We wrap the
controllers with a simple-bus node since they are all connected to the same
chip-select (CS4), in this example external address decoding is provided:
gmi@70090000 {
compatible = "nvidia,tegra20-gmi";
reg = <0x70009000 0x1000>;
#address-cells = <2>;
#size-cells = <1>;
clocks = <&tegra_car TEGRA20_CLK_NOR>;
clock-names = "gmi";
resets = <&tegra_car 42>;
reset-names = "gmi";
ranges = <4 0 0xd0000000 0xfffffff>;
status = "okay";
bus@4,0 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 4 0 0x40100>;
nvidia,snor-mux-mode;
nvidia,snor-adv-active-high;
can@0 {
reg = <0 0x100>;
...
};
can@40000 {
reg = <0x40000 0x100>;
...
};
};
};
Example with one SJA1000 CAN controller connected to the GMI bus
on CS4:
gmi@70090000 {
compatible = "nvidia,tegra20-gmi";
reg = <0x70009000 0x1000>;
#address-cells = <2>;
#size-cells = <1>;
clocks = <&tegra_car TEGRA20_CLK_NOR>;
clock-names = "gmi";
resets = <&tegra_car 42>;
reset-names = "gmi";
ranges = <4 0 0xd0000000 0xfffffff>;
status = "okay";
can@4,0 {
reg = <4 0 0x100>;
nvidia,snor-mux-mode;
nvidia,snor-adv-active-high;
...
};
};

20
Documentation/devicetree/bindings/bus/ti,da850-mstpri.txt Normal file
View File

@@ -0,0 +1,20 @@
* Device tree bindings for Texas Instruments da8xx master peripheral
priority driver
DA8XX SoCs feature a set of registers allowing to change the priority of all
peripherals classified as masters.
Documentation:
OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
Required properties:
- compatible: "ti,da850-mstpri" - for da850 based boards
- reg: offset and length of the mstpri registers
Example for da850-lcdk is shown below.
mstpri {
compatible = "ti,da850-mstpri";
reg = <0x14110 0x0c>;
};

108
Documentation/devicetree/bindings/firmware/nvidia,tegra186-bpmp.txt Normal file
View File

@@ -0,0 +1,108 @@
NVIDIA Tegra Boot and Power Management Processor (BPMP)
The BPMP is a specific processor in Tegra chip, which is designed for
booting process handling and offloading the power management, clock
management, and reset control tasks from the CPU. The binding document
defines the resources that would be used by the BPMP firmware driver,
which can create the interprocessor communication (IPC) between the CPU
and BPMP.
Required properties:
- name : Should be bpmp
- compatible
Array of strings
One of:
- "nvidia,tegra186-bpmp"
- mboxes : The phandle of mailbox controller and the mailbox specifier.
- shmem : List of the phandle of the TX and RX shared memory area that
the IPC between CPU and BPMP is based on.
- #clock-cells : Should be 1.
- #power-domain-cells : Should be 1.
- #reset-cells : Should be 1.
This node is a mailbox consumer. See the following files for details of
the mailbox subsystem, and the specifiers implemented by the relevant
provider(s):
- .../mailbox/mailbox.txt
- .../mailbox/nvidia,tegra186-hsp.txt
This node is a clock, power domain, and reset provider. See the following
files for general documentation of those features, and the specifiers
implemented by this node:
- .../clock/clock-bindings.txt
- <dt-bindings/clock/tegra186-clock.h>
- ../power/power_domain.txt
- <dt-bindings/power/tegra186-powergate.h>
- .../reset/reset.txt
- <dt-bindings/reset/tegra186-reset.h>
The BPMP implements some services which must be represented by separate nodes.
For example, it can provide access to certain I2C controllers, and the I2C
bindings represent each I2C controller as a device tree node. Such nodes should
be nested directly inside the main BPMP node.
Software can determine whether a child node of the BPMP node represents a device
by checking for a compatible property. Any node with a compatible property
represents a device that can be instantiated. Nodes without a compatible
property may be used to provide configuration information regarding the BPMP
itself, although no such configuration nodes are currently defined by this
binding.
The BPMP firmware defines no single global name-/numbering-space for such
services. Put another way, the numbering scheme for I2C buses is distinct from
the numbering scheme for any other service the BPMP may provide (e.g. a future
hypothetical SPI bus service). As such, child device nodes will have no reg
property, and the BPMP node will have no #address-cells or #size-cells property.
The shared memory bindings for BPMP
-----------------------------------
The shared memory area for the IPC TX and RX between CPU and BPMP are
predefined and work on top of sysram, which is an SRAM inside the chip.
See ".../sram/sram.txt" for the bindings.
Example:
hsp_top0: hsp@03c00000 {
...
#mbox-cells = <2>;
};
sysram@30000000 {
compatible = "nvidia,tegra186-sysram", "mmio-sram";
reg = <0x0 0x30000000 0x0 0x50000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0 0x0 0x0 0x30000000 0x0 0x50000>;
cpu_bpmp_tx: shmem@4e000 {
compatible = "nvidia,tegra186-bpmp-shmem";
reg = <0x0 0x4e000 0x0 0x1000>;
label = "cpu-bpmp-tx";
pool;
};
cpu_bpmp_rx: shmem@4f000 {
compatible = "nvidia,tegra186-bpmp-shmem";
reg = <0x0 0x4f000 0x0 0x1000>;
label = "cpu-bpmp-rx";
pool;
};
};
bpmp {
compatible = "nvidia,tegra186-bpmp";
mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_BPMP>;
shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
#clock-cells = <1>;
#power-domain-cells = <1>;
#reset-cells = <1>;
i2c {
compatible = "...";
...
};
};

2
Documentation/devicetree/bindings/firmware/qcom,scm.txt
View File

@@ -10,8 +10,10 @@ Required properties:
* "qcom,scm-apq8064" for APQ8064 platforms
* "qcom,scm-msm8660" for MSM8660 platforms
* "qcom,scm-msm8690" for MSM8690 platforms
* "qcom,scm-msm8996" for MSM8996 platforms
* "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc)
- clocks: One to three clocks may be required based on compatible.
* No clock required for "qcom,scm-msm8996"
* Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960"
* Core, iface, and bus clocks required for "qcom,scm"
- clock-names: Must contain "core" for the core clock, "iface" for the interface

52
Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt Normal file
View File

@@ -0,0 +1,52 @@
NVIDIA Tegra Hardware Synchronization Primitives (HSP)
The HSP modules are used for the processors to share resources and communicate
together. It provides a set of hardware synchronization primitives for
interprocessor communication. So the interprocessor communication (IPC)
protocols can use hardware synchronization primitives, when operating between
two processors not in an SMP relationship.
The features that HSP supported are shared mailboxes, shared semaphores,
arbitrated semaphores and doorbells.
Required properties:
- name : Should be hsp
- compatible
Array of strings.
one of:
- "nvidia,tegra186-hsp"
- reg : Offset and length of the register set for the device.
- interrupt-names
Array of strings.
Contains a list of names for the interrupts described by the interrupt
property. May contain the following entries, in any order:
- "doorbell"
Users of this binding MUST look up entries in the interrupt property
by name, using this interrupt-names property to do so.
- interrupts
Array of interrupt specifiers.
Must contain one entry per entry in the interrupt-names property,
in a matching order.
- #mbox-cells : Should be 2.
The mbox specifier of the "mboxes" property in the client node should
contain two data. The first one should be the HSP type and the second
one should be the ID that the client is going to use. Those information
can be found in the following file.
- <dt-bindings/mailbox/tegra186-hsp.h>.
Example:
hsp_top0: hsp@3c00000 {
compatible = "nvidia,tegra186-hsp";
reg = <0x0 0x03c00000 0x0 0xa0000>;
interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "doorbell";
#mbox-cells = <2>;
};
client {
...
mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB TEGRA_HSP_DB_MASTER_XXX>;
};

20
Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt Normal file
View File

@@ -0,0 +1,20 @@
* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller
The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features
a set of registers which allow to tweak the controller's behavior.
Documentation:
OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
Required properties:
- compatible: "ti,da850-ddr-controller" - for da850 SoC based boards
- reg: a tuple containing the base address of the memory
controller and the size of the memory area to map
Example for da850 shown below.
ddrctl {
compatible = "ti,da850-ddr-controller";
reg = <0xb0000000 0xe8>;
};

8
Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
View File

@@ -1,12 +1,14 @@
DT bindings for the Renesas R-Car System Controller
DT bindings for the Renesas R-Car (RZ/G) System Controller
== System Controller Node ==
The R-Car System Controller provides power management for the CPU cores and
various coprocessors.
The R-Car (RZ/G) System Controller provides power management for the CPU cores
and various coprocessors.
Required properties:
- compatible: Must contain exactly one of the following:
- "renesas,r8a7743-sysc" (RZ/G1M)
- "renesas,r8a7745-sysc" (RZ/G1E)
- "renesas,r8a7779-sysc" (R-Car H1)
- "renesas,r8a7790-sysc" (R-Car H2)
- "renesas,r8a7791-sysc" (R-Car M2-W)

44
Documentation/devicetree/bindings/reset/oxnas,reset.txt
View File

@@ -5,45 +5,19 @@ Please also refer to reset.txt in this directory for common reset
controller binding usage.
Required properties:
- compatible: Should be "oxsemi,ox810se-reset"
- compatible: For OX810SE, should be "oxsemi,ox810se-reset"
For OX820, should be "oxsemi,ox820-reset"
- #reset-cells: 1, see below
Parent node should have the following properties :
- compatible: Should be "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"
- compatible: For OX810SE, should be :
"oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"
For OX820, should be :
"oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd"
For OX810SE, the indices are :
- 0 : ARM
- 1 : COPRO
- 2 : Reserved
- 3 : Reserved
- 4 : USBHS
- 5 : USBHSPHY
- 6 : MAC
- 7 : PCI
- 8 : DMA
- 9 : DPE
- 10 : DDR
- 11 : SATA
- 12 : SATA_LINK
- 13 : SATA_PHY
- 14 : Reserved
- 15 : NAND
- 16 : GPIO
- 17 : UART1
- 18 : UART2
- 19 : MISC
- 20 : I2S
- 21 : AHB_MON
- 22 : UART3
- 23 : UART4
- 24 : SGDMA
- 25 : Reserved
- 26 : Reserved
- 27 : Reserved
- 28 : Reserved
- 29 : Reserved
- 30 : Reserved
- 31 : BUS
Reset indices are in dt-bindings include files :
- For OX810SE: include/dt-bindings/reset/oxsemi,ox810se.h
- For OX820: include/dt-bindings/reset/oxsemi,ox820.h
example:

2
Documentation/devicetree/bindings/sram/sram.txt
View File

@@ -4,7 +4,7 @@ Simple IO memory regions to be managed by the genalloc API.
Required properties:
- compatible : mmio-sram
- compatible : mmio-sram or atmel,sama5d2-securam
- reg : SRAM iomem address range