Merge git://www.linux-watchdog.org/linux-watchdog

Pull watchdog updates from Wim Van Sebroeck:
 "This adds the following new drivers:

   - ImgTec PDC Watchdog Timer Driver,
   - Mediatek SoC integrated watchdog

  Add support for BCM5301X, IT8783, NCT6791 and NCT6792 WDT's

  Add bcm47xx_wdt and da9063 restart handlers and contains overall
  improvements and fixes"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: bcm47xx_wdt.c: allow enabling on BCM5301X arch
  watchdog: jz4740: Add DT support
  dt: watchdog: Add DT binding documentation for jz4740 watchdog timer
  watchdog: dw_wdt: Try to get a 30 second watchdog by default
  watchdog: dw_wdt: pat the watchdog before enabling it
  watchdog: w83627hf_wdt: Add support for NCT6791 and NCT6792
  watchdog: bcm47xx_wdt.c: add restart handler support
  watchdog: gpio_wdt: Add "always_running" feature to GPIO watchdog
  watchdog: da9063: Add restart handler support
  ARM: mediatek: dts: Add bindings for watchdog
  watchdog: Add driver for Mediatek watchdog
  watchdog: Fix omap watchdogs to enable the magic close bit
  watchdog: rt2880_wdt: minor clean up
  watchdog: hpwdt: Fix initialization message in hpwdt.c
  watchdog: it87_wdt: add IT8783 ID
  watchdog: imx2: Constify struct regmap_config and watchdog_ops
  DT: watchdog: Add ImgTec PDC Watchdog Timer binding documentation
  watchdog: ImgTec PDC Watchdog Timer Driver

Documentation/devicetree/bindings/watchdog/gpio-wdt.txt

@@ -13,6 +13,11 @@ Required Properties:
     by the GPIO flags.
 - hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds).
 
+Optional Properties:
+- always-running: If the watchdog timer cannot be disabled, add this flag to
+  have the driver keep toggling the signal without a client. It will only cease
+  to toggle the signal when the device is open and the timeout elapsed.
+
 Example:
 	watchdog: watchdog {
 		/* ADM706 */

Documentation/devicetree/bindings/watchdog/imgpdc-wdt.txt

@@ -0,0 +1,19 @@
+*ImgTec PowerDown Controller (PDC) Watchdog Timer (WDT)
+
+Required properties:
+- compatible : Should be "img,pdc-wdt"
+- reg : Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdt" and "sys"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts : Should contain WDT interrupt
+
+Examples:
+
+watchdog@18102100 {
+	compatible = "img,pdc-wdt";
+	reg = <0x18102100 0x100>;
+	clocks = <&pdc_wdt_clk>, <&sys_clk>;
+	clock-names = "wdt", "sys";
+	interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+};

Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt

@@ -0,0 +1,12 @@
+Ingenic Watchdog Timer (WDT) Controller for JZ4740
+
+Required properties:
+compatible: "ingenic,jz4740-watchdog"
+reg: Register address and length for watchdog registers
+
+Example:
+
+watchdog: jz4740-watchdog@0x10002000 {
+	compatible = "ingenic,jz4740-watchdog";
+	reg = <0x10002000 0x100>;
+};

Documentation/devicetree/bindings/watchdog/mtk-wdt.txt

@@ -0,0 +1,13 @@
+Mediatek SoCs Watchdog timer
+
+Required properties:
+
+- compatible : should be "mediatek,mt6589-wdt"
+- reg : Specifies base physical address and size of the registers.
+
+Example:
+
+wdt: watchdog@010000000 {
+	compatible = "mediatek,mt6589-wdt";
+	reg = <0x10000000 0x18>;
+};