Merge tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6

MTD pull for 3.3

* tag 'for-linus-3.3' of git://git.infradead.org/mtd-2.6: (113 commits)
  mtd: Fix dependency for MTD_DOC200x
  mtd: do not use mtd->block_markbad directly
  logfs: do not use 'mtd->block_isbad' directly
  mtd: introduce mtd_can_have_bb helper
  mtd: do not use mtd->suspend and mtd->resume directly
  mtd: do not use mtd->lock, unlock and is_locked directly
  mtd: do not use mtd->sync directly
  mtd: harmonize mtd_writev usage
  mtd: do not use mtd->lock_user_prot_reg directly
  mtd: mtd->write_user_prot_reg directly
  mtd: do not use mtd->read_*_prot_reg directly
  mtd: do not use mtd->get_*_prot_info directly
  mtd: do not use mtd->read_oob directly
  mtd: mtdoops: do not use mtd->panic_write directly
  romfs: do not use mtd->get_unmapped_area directly
  mtd: do not use mtd->get_unmapped_area directly
  mtd: do use mtd->point directly
  mtd: introduce mtd_has_oob helper
  mtd: mtdcore: export symbols cleanup
  mtd: clean-up the default_mtd_writev function
  ...

Fix up trivial edit/remove conflict in drivers/staging/spectra/lld_mtd.c

Documentation/devicetree/bindings/mtd/gpio-control-nand.txt

@@ -0,0 +1,44 @@
+GPIO assisted NAND flash
+
+The GPIO assisted NAND flash uses a memory mapped interface to
+read/write the NAND commands and data and GPIO pins for the control
+signals.
+
+Required properties:
+- compatible : "gpio-control-nand"
+- reg : should specify localbus chip select and size used for the chip.  The
+  resource describes the data bus connected to the NAND flash and all accesses
+  are made in native endianness.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- gpios : specifies the gpio pins to control the NAND device.  nwp is an
+  optional gpio and may be set to 0 if not present.
+
+Optional properties:
+- bank-width : Width (in bytes) of the device.  If not present, the width
+  defaults to 1 byte.
+- chip-delay : chip dependent delay for transferring data from array to
+  read registers (tR).  If not present then a default of 20us is used.
+- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read
+  location used to guard against bus reordering with regards to accesses to
+  the GPIO's and the NAND flash data bus.  If present, then after changing
+  GPIO state and before and after command byte writes, this register will be
+  read to ensure that the GPIO accesses have completed.
+
+Examples:
+
+gpio-nand@1,0 {
+	compatible = "gpio-control-nand";
+	reg = <1 0x0000 0x2>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	gpios = <&banka 1 0	/* rdy */
+		 &banka 2 0 	/* nce */
+		 &banka 3 0 	/* ale */
+		 &banka 4 0 	/* cle */
+		 0		/* nwp */>;
+
+	partition@0 {
+	...
+	};
+};