Merge tag 'nand/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next

Core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection

Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion

Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC

Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt

@@ -7,14 +7,16 @@ Required properties:
 - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
 
 Optional properties:
-- fsl,upm-wait-flags : add chip-dependent short delays after running the
-	UPM pattern (0x1), after writing a data byte (0x2) or after
-	writing out a buffer (0x4).
 - fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
 	The corresponding address lines are used to select the chip.
 - gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
 	(R/B#). For multi-chip devices, "n" GPIO definitions are required
 	according to the number of chips.
+
+Deprecated properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+	UPM pattern (0x1), after writing a data byte (0x2) or after
+	writing out a buffer (0x4).
 - chip-delay : chip dependent delay for transferring data from array to
 	read registers (tR). Required if property "gpios" is not used
 	(R/B# pins not connected).
@@ -52,8 +54,6 @@ upm@3,0 {
 	fsl,upm-cmd-offset = <0x08>;
 	/* Multi-chip NAND device */
 	fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
-	fsl,upm-wait-flags = <0x5>;
-	chip-delay = <25>; // in micro-seconds
 
 	nand@0 {
 		#address-cells = <1>;

Documentation/devicetree/bindings/mtd/nand-controller.yaml

@@ -114,6 +114,13 @@ patternProperties:
         description:
           Contains the native Ready/Busy IDs.
 
+      rb-gpios:
+        description:
+          Contains one or more GPIO descriptor (the numper of descriptor
+          depends on the number of R/B pins exposed by the flash) for the
+          Ready/Busy pins. Active state refers to the NAND ready state and
+          should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted.
+
     required:
       - reg