Merge branch 'imx/dt' into next/dt

Documentation/devicetree/bindings/arm/sirf.txt

@@ -0,0 +1,3 @@
+prima2 "cb" evalutation board
+Required root node properties:
+    - compatible = "sirf,prima2-cb", "sirf,prima2";

Documentation/devicetree/bindings/arm/xilinx.txt

@@ -0,0 +1,7 @@
+Xilinx Zynq EP107 Emulation Platform board
+
+This board is an emulation platform for the Zynq product which is
+based on an ARM Cortex A9 processor.
+
+Required root node properties:
+    - compatible = "xlnx,zynq-ep107";

Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt

@@ -0,0 +1,17 @@
+* Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<chip>-sdma"
+- reg : Should contain SDMA registers location and length
+- interrupts : Should contain SDMA interrupt
+- fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM
+  scripts firmware
+
+Examples:
+
+sdma@83fb0000 {
+	compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
+	reg = <0x83fb0000 0x4000>;
+	interrupts = <6>;
+	fsl,sdma-ram-script-name = "sdma-imx51.bin";
+};

Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt

@@ -0,0 +1,34 @@
+* Freescale Enhanced Secure Digital Host Controller (eSDHC) for i.MX
+
+The Enhanced Secure Digital Host Controller on Freescale i.MX family
+provides an interface for MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible : Should be "fsl,<chip>-esdhc"
+- reg : Should contain eSDHC registers location and length
+- interrupts : Should contain eSDHC interrupt
+
+Optional properties:
+- fsl,card-wired : Indicate the card is wired to host permanently
+- fsl,cd-internal : Indicate to use controller internal card detection
+- fsl,wp-internal : Indicate to use controller internal write protection
+- cd-gpios : Specify GPIOs for card detection
+- wp-gpios : Specify GPIOs for write protection
+
+Examples:
+
+esdhc@70004000 {
+	compatible = "fsl,imx51-esdhc";
+	reg = <0x70004000 0x4000>;
+	interrupts = <1>;
+	fsl,cd-internal;
+	fsl,wp-internal;
+};
+
+esdhc@70008000 {
+	compatible = "fsl,imx51-esdhc";
+	reg = <0x70008000 0x4000>;
+	interrupts = <2>;
+	cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */
+	wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */
+};

Documentation/devicetree/bindings/net/fsl-fec.txt

@@ -0,0 +1,24 @@
+* Freescale Fast Ethernet Controller (FEC)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-fec"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain fec interrupt
+- phy-mode : String, operation mode of the PHY interface.
+  Supported values are: "mii", "gmii", "sgmii", "tbi", "rmii",
+  "rgmii", "rgmii-id", "rgmii-rxid", "rgmii-txid", "rtbi", "smii".
+- phy-reset-gpios : Should specify the gpio for phy reset
+
+Optional properties:
+- local-mac-address : 6 bytes, mac address
+
+Example:
+
+fec@83fec000 {
+	compatible = "fsl,imx51-fec", "fsl,imx27-fec";
+	reg = <0x83fec000 0x4000>;
+	interrupts = <87>;
+	phy-mode = "mii";
+	phy-reset-gpios = <&gpio1 14 0>; /* GPIO2_14 */
+	local-mac-address = [00 04 9F 01 1B B9];
+};

Documentation/devicetree/bindings/rtc/olpc-xo1-rtc.txt

@@ -0,0 +1,5 @@
+OLPC XO-1 RTC
+~~~~~~~~~~~~~
+
+Required properties:
+ - compatible : "olpc,xo1-rtc"

Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt

@@ -0,0 +1,19 @@
+* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART)
+
+Required properties:
+- compatible : Should be "fsl,<soc>-uart"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain uart interrupt
+
+Optional properties:
+- fsl,uart-has-rtscts : Indicate the uart has rts and cts
+- fsl,irda-mode : Indicate the uart supports irda mode
+
+Example:
+
+uart@73fbc000 {
+	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
+	reg = <0x73fbc000 0x4000>;
+	interrupts = <31>;
+	fsl,uart-has-rtscts;
+};