ASoC: Ux500: Move MSP pinctrl setup into the MSP driver
In the initial submission of the MSP driver msp1 and msp3's associated pinctrl mechanism was passed back to platform code using a plat_init() call-back routine, but it has no place in platform code. The MSP driver should set this up for the appropriate ports. Instead we use a use_pinctrl identifier which is passed from platform_data/Device Tree which indicates which ports should use pinctrl. Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
This commit is contained in:
@@ -15,6 +15,7 @@
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/pinctrl/consumer.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
@@ -25,6 +26,9 @@
|
||||
|
||||
#include "ux500_msp_i2s.h"
|
||||
|
||||
/* MSP1/3 Tx/Rx usage protection */
|
||||
static DEFINE_SPINLOCK(msp_rxtx_lock);
|
||||
|
||||
/* Protocol desciptors */
|
||||
static const struct msp_protdesc prot_descs[] = {
|
||||
{ /* I2S */
|
||||
@@ -352,17 +356,23 @@ static int configure_multichannel(struct ux500_msp *msp,
|
||||
|
||||
static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config)
|
||||
{
|
||||
int status = 0;
|
||||
int status = 0, retval = 0;
|
||||
u32 reg_val_DMACR, reg_val_GCR;
|
||||
unsigned long flags;
|
||||
|
||||
/* Check msp state whether in RUN or CONFIGURED Mode */
|
||||
if ((msp->msp_state == MSP_STATE_IDLE) && (msp->plat_init)) {
|
||||
status = msp->plat_init();
|
||||
if (status) {
|
||||
dev_err(msp->dev, "%s: ERROR: Failed to init MSP (%d)!\n",
|
||||
__func__, status);
|
||||
return status;
|
||||
if (msp->msp_state == MSP_STATE_IDLE) {
|
||||
spin_lock_irqsave(&msp_rxtx_lock, flags);
|
||||
if (msp->pinctrl_rxtx_ref == 0 &&
|
||||
!(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_def))) {
|
||||
retval = pinctrl_select_state(msp->pinctrl_p,
|
||||
msp->pinctrl_def);
|
||||
if (retval)
|
||||
pr_err("could not set MSP defstate\n");
|
||||
}
|
||||
if (!retval)
|
||||
msp->pinctrl_rxtx_ref++;
|
||||
spin_unlock_irqrestore(&msp_rxtx_lock, flags);
|
||||
}
|
||||
|
||||
/* Configure msp with protocol dependent settings */
|
||||
@@ -620,7 +630,8 @@ int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction)
|
||||
|
||||
int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
|
||||
{
|
||||
int status = 0;
|
||||
int status = 0, retval = 0;
|
||||
unsigned long flags;
|
||||
|
||||
dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir);
|
||||
|
||||
@@ -631,12 +642,19 @@ int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
|
||||
writel((readl(msp->registers + MSP_GCR) &
|
||||
(~(FRAME_GEN_ENABLE | SRG_ENABLE))),
|
||||
msp->registers + MSP_GCR);
|
||||
if (msp->plat_exit)
|
||||
status = msp->plat_exit();
|
||||
if (status)
|
||||
dev_warn(msp->dev,
|
||||
"%s: WARN: ux500_msp_i2s_exit failed (%d)!\n",
|
||||
__func__, status);
|
||||
|
||||
spin_lock_irqsave(&msp_rxtx_lock, flags);
|
||||
WARN_ON(!msp->pinctrl_rxtx_ref);
|
||||
msp->pinctrl_rxtx_ref--;
|
||||
if (msp->pinctrl_rxtx_ref == 0 &&
|
||||
!(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_sleep))) {
|
||||
retval = pinctrl_select_state(msp->pinctrl_p,
|
||||
msp->pinctrl_sleep);
|
||||
if (retval)
|
||||
pr_err("could not set MSP sleepstate\n");
|
||||
}
|
||||
spin_unlock_irqrestore(&msp_rxtx_lock, flags);
|
||||
|
||||
writel(0, msp->registers + MSP_GCR);
|
||||
writel(0, msp->registers + MSP_TCF);
|
||||
writel(0, msp->registers + MSP_RCF);
|
||||
@@ -675,8 +693,6 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
|
||||
|
||||
msp->id = platform_data->id;
|
||||
msp->dev = &pdev->dev;
|
||||
msp->plat_init = platform_data->msp_i2s_init;
|
||||
msp->plat_exit = platform_data->msp_i2s_exit;
|
||||
msp->dma_cfg_rx = platform_data->msp_i2s_dma_rx;
|
||||
msp->dma_cfg_tx = platform_data->msp_i2s_dma_tx;
|
||||
|
||||
@@ -713,6 +729,25 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
|
||||
dev_dbg(&pdev->dev, "I2S device-name: '%s'\n", i2s_cont->name);
|
||||
msp->i2s_cont = i2s_cont;
|
||||
|
||||
msp->pinctrl_p = pinctrl_get(msp->dev);
|
||||
if (IS_ERR(msp->pinctrl_p))
|
||||
dev_err(&pdev->dev, "could not get MSP pinctrl\n");
|
||||
else {
|
||||
msp->pinctrl_def = pinctrl_lookup_state(msp->pinctrl_p,
|
||||
PINCTRL_STATE_DEFAULT);
|
||||
if (IS_ERR(msp->pinctrl_def)) {
|
||||
dev_err(&pdev->dev,
|
||||
"could not get MSP defstate (%li)\n",
|
||||
PTR_ERR(msp->pinctrl_def));
|
||||
}
|
||||
msp->pinctrl_sleep = pinctrl_lookup_state(msp->pinctrl_p,
|
||||
PINCTRL_STATE_SLEEP);
|
||||
if (IS_ERR(msp->pinctrl_sleep))
|
||||
dev_err(&pdev->dev,
|
||||
"could not get MSP idlestate (%li)\n",
|
||||
PTR_ERR(msp->pinctrl_def));
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
Reference in New Issue
Block a user