Merge git://www.linux-watchdog.org/linux-watchdog

Pull watchdog updates from Wim Van Sebroeck:
 - new driver for NXP LPC18xx Watchdog Timer
 - new driver for SAMA5D4 watchdog timer
 - add support for MCP79 to nv_tco driver
 - clean-up and improvement of the mpc8xxx watchdog driver
 - improvements to gpio-wdt
 - at91sam9_wdt clock improvements
 ... and other small fixes and improvements

* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
  Watchdog: Fix parent of watchdog_devices
  watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
  watchdog: at91sam9: get and use slow clock
  Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
  watchdog: add a driver to support SAMA5D4 watchdog timer
  watchdog: mpc8xxx: allow to compile for MPC512x
  watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
  watchdog: mpc8xxx: use dynamic memory for device specific data
  watchdog: mpc8xxx: use devm_ioremap_resource to map memory
  watchdog: mpc8xxx: make use of of_device_get_match_data
  watchdog: mpc8xxx: simplify registration
  watchdog: mpc8xxx: remove dead code
  watchdog: lpc18xx_wdt_get_timeleft() can be static
  DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
  watchdog: NXP LPC18xx Watchdog Timer Driver
  watchdog: gpio-wdt: ping already at startup for always running devices
  watchdog: gpio-wdt: be more strict about hw_algo matching
  Documentation: watchdog: at91sam9_wdt: add clocks property
  watchdog: booke_wdt: Use infrastructure to check timeout limits
  watchdog: (nv_tco) add support for MCP79
  ...

Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt

@@ -0,0 +1,35 @@
+* Atmel SAMA5D4 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: "atmel,sama5d4-wdt"
+- reg: base physical address and length of memory mapped region.
+
+Optional properties:
+- timeout-sec: watchdog timeout value (in seconds).
+- interrupts: interrupt number to the CPU.
+- atmel,watchdog-type: should be "hardware" or "software".
+	"hardware": enable watchdog fault reset. A watchdog fault triggers
+		    watchdog reset.
+	"software": enable watchdog fault interrupt. A watchdog fault asserts
+		    watchdog interrupt.
+- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
+		   in idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
+		  in debug state.
+
+Example:
+	watchdog@fc068640 {
+		compatible = "atmel,sama5d4-wdt";
+		reg = <0xfc068640 0x10>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>;
+		timeout-sec = <10>;
+		atmel,watchdog-type = "hardware";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		status = "okay";
+	};

Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt

@@ -0,0 +1,19 @@
+* NXP LPC18xx Watchdog Timer (WDT)
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-wwdt"
+- reg: Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts: Should contain WDT interrupt
+
+Examples:
+
+watchdog@40080000 {
+	compatible = "nxp,lpc1850-wwdt";
+	reg = <0x40080000 0x24>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+	clock-names = "wdtclk", "reg";
+	interrupts = <49>;
+};