Merge remote-tracking branches 'asoc/topic/rt5645', 'asoc/topic/rt5670', 'asoc/topic/rt5677', 'asoc/topic/samsung' and 'asoc/topic/sgtl5000' into asoc-next

2014-12-08 13:12:09 +00:00
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -16,6 +16,7 @@
 #include <linux/pm.h>
 #include <linux/i2c.h>
 #include <linux/clk.h>
+#include <linux/log2.h>
 #include <linux/regmap.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
@@ -121,6 +122,13 @@ struct ldo_regulator {
 	bool enabled;
 };

+enum sgtl5000_micbias_resistor {
+	SGTL5000_MICBIAS_OFF = 0,
+	SGTL5000_MICBIAS_2K = 2,
+	SGTL5000_MICBIAS_4K = 4,
+	SGTL5000_MICBIAS_8K = 8,
+};
+
 /* sgtl5000 private structure in codec */
 struct sgtl5000_priv {
 	int sysclk;	/* sysclk rate */
@@ -131,6 +139,8 @@ struct sgtl5000_priv {
 	struct regmap *regmap;
 	struct clk *mclk;
 	int revision;
+	u8 micbias_resistor;
+	u8 micbias_voltage;
 };

 /*
@@ -145,12 +155,14 @@ struct sgtl5000_priv {
 static int mic_bias_event(struct snd_soc_dapm_widget *w,
 	struct snd_kcontrol *kcontrol, int event)
 {
+	struct sgtl5000_priv *sgtl5000 = snd_soc_codec_get_drvdata(w->codec);
+
 	switch (event) {
 	case SND_SOC_DAPM_POST_PMU:
-		/* change mic bias resistor to 4Kohm */
+		/* change mic bias resistor */
 		snd_soc_update_bits(w->codec, SGTL5000_CHIP_MIC_CTRL,
-				SGTL5000_BIAS_R_MASK,
-				SGTL5000_BIAS_R_4k << SGTL5000_BIAS_R_SHIFT);
+			SGTL5000_BIAS_R_MASK,
+			sgtl5000->micbias_resistor << SGTL5000_BIAS_R_SHIFT);
 		break;

 	case SND_SOC_DAPM_PRE_PMD:
@@ -530,16 +542,16 @@ static int sgtl5000_set_dai_sysclk(struct snd_soc_dai *codec_dai,

 /*
 * set clock according to i2s frame clock,
- * sgtl5000 provide 2 clock sources.
- * 1. sys_mclk. sample freq can only configure to
+ * sgtl5000 provides 2 clock sources:
+ * 1. sys_mclk: sample freq can only be configured to
 *	1/256, 1/384, 1/512 of sys_mclk.
- * 2. pll. can derive any audio clocks.
+ * 2. pll: can derive any audio clocks.
 *
 * clock setting rules:
- * 1. in slave mode, only sys_mclk can use.
- * 2. as constraint by sys_mclk, sample freq should
- *	set to 32k, 44.1k and above.
- * 3. using sys_mclk prefer to pll to save power.
+ * 1. in slave mode, only sys_mclk can be used
+ * 2. as constraint by sys_mclk, sample freq should be set to 32 kHz, 44.1 kHz
+ * and above.
+ * 3. usage of sys_mclk is preferred over pll to save power.
 */
 static int sgtl5000_set_clock(struct snd_soc_codec *codec, int frame_rate)
 {
@@ -549,8 +561,8 @@ static int sgtl5000_set_clock(struct snd_soc_codec *codec, int frame_rate)

 	/*
 	 * sample freq should be divided by frame clock,
-	 * if frame clock lower than 44.1khz, sample feq should set to
-	 * 32khz or 44.1khz.
+	 * if frame clock is lower than 44.1 kHz, sample freq should be set to
+	 * 32 kHz or 44.1 kHz.
 	 */
 	switch (frame_rate) {
 	case 8000:
@@ -603,9 +615,10 @@ static int sgtl5000_set_clock(struct snd_soc_codec *codec, int frame_rate)

 	/*
 	 * calculate the divider of mclk/sample_freq,
-	 * factor of freq =96k can only be 256, since mclk in range (12m,27m)
+	 * factor of freq = 96 kHz can only be 256, since mclk is in the range
+	 * of 8 MHz - 27 MHz
 	 */
-	switch (sgtl5000->sysclk / sys_fs) {
+	switch (sgtl5000->sysclk / frame_rate) {
 	case 256:
 		clk_ctl |= SGTL5000_MCLK_FREQ_256FS <<
 			SGTL5000_MCLK_FREQ_SHIFT;
@@ -619,7 +632,7 @@ static int sgtl5000_set_clock(struct snd_soc_codec *codec, int frame_rate)
 			SGTL5000_MCLK_FREQ_SHIFT;
 		break;
 	default:
-		/* if mclk not satisify the divider, use pll */
+		/* if mclk does not satisfy the divider, use pll */
 		if (sgtl5000->master) {
 			clk_ctl |= SGTL5000_MCLK_FREQ_PLL <<
 				SGTL5000_MCLK_FREQ_SHIFT;
@@ -628,7 +641,7 @@ static int sgtl5000_set_clock(struct snd_soc_codec *codec, int frame_rate)
 				"PLL not supported in slave mode\n");
 			dev_err(codec->dev, "%d ratio is not supported. "
 				"SYS_MCLK needs to be 256, 384 or 512 * fs\n",
-				sgtl5000->sysclk / sys_fs);
+				sgtl5000->sysclk / frame_rate);
 			return -EINVAL;
 		}
 	}
@@ -795,7 +808,7 @@ static int ldo_regulator_enable(struct regulator_dev *dev)
 				SGTL5000_LINEREG_D_POWERUP,
 				SGTL5000_LINEREG_D_POWERUP);

-	/* when internal ldo enabled, simple digital power can be disabled */
+	/* when internal ldo is enabled, simple digital power can be disabled */
 	snd_soc_update_bits(codec, SGTL5000_CHIP_ANA_POWER,
 				SGTL5000_LINREG_SIMPLE_POWERUP,
 				0);
@@ -1079,7 +1092,7 @@ static bool sgtl5000_readable(struct device *dev, unsigned int reg)
 /*
 * sgtl5000 has 3 internal power supplies:
 * 1. VAG, normally set to vdda/2
- * 2. chargepump, set to different value
+ * 2. charge pump, set to different value
 *	according to voltage of vdda and vddio
 * 3. line out VAG, normally set to vddio/2
 *
@@ -1325,8 +1338,13 @@ static int sgtl5000_probe(struct snd_soc_codec *codec)
 			SGTL5000_HP_ZCD_EN |
 			SGTL5000_ADC_ZCD_EN);

-	snd_soc_write(codec, SGTL5000_CHIP_MIC_CTRL, 2);
+	snd_soc_update_bits(codec, SGTL5000_CHIP_MIC_CTRL,
+			SGTL5000_BIAS_R_MASK,
+			sgtl5000->micbias_resistor << SGTL5000_BIAS_R_SHIFT);

+	snd_soc_update_bits(codec, SGTL5000_CHIP_MIC_CTRL,
+			SGTL5000_BIAS_R_MASK,
+			sgtl5000->micbias_voltage << SGTL5000_BIAS_R_SHIFT);
 	/*
 	 * disable DAP
 	 * TODO:
@@ -1416,10 +1434,10 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
 {
 	struct sgtl5000_priv *sgtl5000;
 	int ret, reg, rev;
-	unsigned int mclk;
+	struct device_node *np = client->dev.of_node;
+	u32 value;

-	sgtl5000 = devm_kzalloc(&client->dev, sizeof(struct sgtl5000_priv),
-								GFP_KERNEL);
+	sgtl5000 = devm_kzalloc(&client->dev, sizeof(*sgtl5000), GFP_KERNEL);
 	if (!sgtl5000)
 		return -ENOMEM;

@@ -1440,14 +1458,6 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
 		return ret;
 	}

-	/* SGTL5000 SYS_MCLK should be between 8 and 27 MHz */
-	mclk = clk_get_rate(sgtl5000->mclk);
-	if (mclk < 8000000 || mclk > 27000000) {
-		dev_err(&client->dev, "Invalid SYS_CLK frequency: %u.%03uMHz\n",
-			mclk / 1000000, mclk / 1000 % 1000);
-		return -EINVAL;
-	}
-
 	ret = clk_prepare_enable(sgtl5000->mclk);
 	if (ret)
 		return ret;
@@ -1469,6 +1479,47 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
 	dev_info(&client->dev, "sgtl5000 revision 0x%x\n", rev);
 	sgtl5000->revision = rev;

+	if (np) {
+		if (!of_property_read_u32(np,
+			"micbias-resistor-k-ohms", &value)) {
+			switch (value) {
+			case SGTL5000_MICBIAS_OFF:
+				sgtl5000->micbias_resistor = 0;
+				break;
+			case SGTL5000_MICBIAS_2K:
+				sgtl5000->micbias_resistor = 1;
+				break;
+			case SGTL5000_MICBIAS_4K:
+				sgtl5000->micbias_resistor = 2;
+				break;
+			case SGTL5000_MICBIAS_8K:
+				sgtl5000->micbias_resistor = 3;
+				break;
+			default:
+				sgtl5000->micbias_resistor = 2;
+				dev_err(&client->dev,
+					"Unsuitable MicBias resistor\n");
+			}
+		} else {
+			/* default is 4Kohms */
+			sgtl5000->micbias_resistor = 2;
+		}
+		if (!of_property_read_u32(np,
+			"micbias-voltage-m-volts", &value)) {
+			/* 1250mV => 0 */
+			/* steps of 250mV */
+			if ((value >= 1250) && (value <= 3000))
+				sgtl5000->micbias_voltage = (value / 250) - 5;
+			else {
+				sgtl5000->micbias_voltage = 0;
+				dev_err(&client->dev,
+					"Unsuitable MicBias resistor\n");
+			}
+		} else {
+			sgtl5000->micbias_voltage = 0;
+		}
+	}
+
 	i2c_set_clientdata(client, sgtl5000);

 	/* Ensure sgtl5000 will start with sane register values */