Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits) sh: include empty zero page in romImage sh: Make associative cache writes fatal on all SH-4A parts. sh: Drop associative writes for SH-4 cache flushes. sh: Partial revert of copy/clear_user_highpage() optimizations. sh: Add default uImage rule for se7724, ap325rxa, and migor. sh: allow runtime pm without suspend/resume callbacks sh: mach-ecovec24: Remove un-defined settings for VPU sh: mach-ecovec24: LCDC drive ability become high sh: fix sh7724 VEU3F resource size serial: sh-sci: Fix too early port disabling. sh: pfc: pr_info() -> pr_debug() cleanups. sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines. sh: Improve kfr2r09 serial port setup code sh: Break out SuperH PFC code sh: Move KEYSC header file sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file sh: Add CPG save/restore code for sh7724 R-standby sh: Add SDHI power control support to Ecovec mfd: Add power control platform data to SDHI driver sh: mach-ecovec24: modify address map ...
2009-12-09 19:03:16 -08:00
--- a/arch/sh/boards/Makefile
+++ b/arch/sh/boards/Makefile
@@ -1,7 +1,6 @@
 #
 # Specific board support, not covered by a mach group.
 #
-obj-$(CONFIG_SH_AP325RXA)	+= board-ap325rxa.o
 obj-$(CONFIG_SH_MAGIC_PANEL_R2)	+= board-magicpanelr2.o
 obj-$(CONFIG_SH_SH7785LCR)	+= board-sh7785lcr.o
 obj-$(CONFIG_SH_URQUELL)	+= board-urquell.o
--- a/arch/sh/boards/mach-ap325rxa/Makefile
+++ b/arch/sh/boards/mach-ap325rxa/Makefile
@@ -0,0 +1,2 @@
+obj-y	 := setup.o sdram.o
+
--- a/arch/sh/boards/mach-ap325rxa/sdram.S
+++ b/arch/sh/boards/mach-ap325rxa/sdram.S
@@ -0,0 +1,69 @@
+/*
+ * AP325RXA sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(ap325rxa_sdram_enter_start)
+
+	/* SBSC: disable power down and put in self-refresh mode */
+	mov.l	1f, r4
+	mov.l	2f, r1
+	mov.l	@r4, r2
+	or	r1, r2
+	mov.l   3f, r3
+	and	r3, r2
+	mov.l	r2, @r4
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+2:	.long	0x00000400
+3:	.long	0xffff7fff
+ENTRY(ap325rxa_sdram_enter_end)
+
+	.balign 4
+ENTRY(ap325rxa_sdram_leave_start)
+
+	/* SBSC: set auto-refresh mode */
+	mov.l	1f, r4
+	mov.l	@r4, r0
+	mov.l   4f, r1
+	and	r1, r0
+	mov.l	r0, @r4
+	mov.l	6f, r4
+	mov.l	8f, r0
+	mov.l	@r4, r1
+	mov	#-1, r4
+	add	r4, r1
+	or	r1, r0
+	mov.l	7f, r1
+	mov.l	r0, @r1
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+4:	.long	0xfffffbff
+6:	.long   0xfe40001c /* RTCOR */
+7:	.long   0xfe400018 /* RTCNT */
+8:	.long   0xa55a0000
+ENTRY(ap325rxa_sdram_leave_end)
--- a/arch/sh/boards/mach-ap325rxa/setup.c
+++ b/arch/sh/boards/mach-ap325rxa/setup.c
@@ -20,8 +20,6 @@
 #include <linux/i2c.h>
 #include <linux/smsc911x.h>
 #include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_gpio.h>
 #include <media/ov772x.h>
 #include <media/soc_camera.h>
 #include <media/soc_camera_platform.h>
@@ -29,6 +27,7 @@
 #include <video/sh_mobile_lcdc.h>
 #include <asm/io.h>
 #include <asm/clock.h>
+#include <asm/suspend.h>
 #include <cpu/sh7723.h>

 static struct smsc911x_platform_config smsc911x_config = {
@@ -409,17 +408,49 @@ static struct platform_device ceu_device = {
 	},
 };

-struct spi_gpio_platform_data sdcard_cn3_platform_data = {
-	.sck = GPIO_PTD0,
-	.mosi = GPIO_PTD1,
-	.miso = GPIO_PTD2,
-	.num_chipselect = 1,
+static struct resource sdhi0_cn3_resources[] = {
+	[0] = {
+		.name	= "SDHI0",
+		.start	= 0x04ce0000,
+		.end	= 0x04ce01ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 101,
+		.flags  = IORESOURCE_IRQ,
+	},
 };

-static struct platform_device sdcard_cn3_device = {
-	.name		= "spi_gpio",
-	.dev	= {
-		.platform_data	= &sdcard_cn3_platform_data,
+static struct platform_device sdhi0_cn3_device = {
+	.name		= "sh_mobile_sdhi",
+	.id             = 0, /* "sdhi0" clock */
+	.num_resources	= ARRAY_SIZE(sdhi0_cn3_resources),
+	.resource	= sdhi0_cn3_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI0,
+	},
+};
+
+static struct resource sdhi1_cn7_resources[] = {
+	[0] = {
+		.name	= "SDHI1",
+		.start	= 0x04cf0000,
+		.end	= 0x04cf01ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 24,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi1_cn7_device = {
+	.name		= "sh_mobile_sdhi",
+	.id             = 1, /* "sdhi1" clock */
+	.num_resources	= ARRAY_SIZE(sdhi1_cn7_resources),
+	.resource	= sdhi1_cn7_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI1,
 	},
 };

@@ -470,22 +501,26 @@ static struct platform_device *ap325rxa_devices[] __initdata = {
 	&lcdc_device,
 	&ceu_device,
 	&nand_flash_device,
-	&sdcard_cn3_device,
+	&sdhi0_cn3_device,
+	&sdhi1_cn7_device,
 	&ap325rxa_camera[0],
 	&ap325rxa_camera[1],
 };

-static struct spi_board_info ap325rxa_spi_devices[] = {
-	{
-		.modalias = "mmc_spi",
-		.max_speed_hz = 5000000,
-		.chip_select = 0,
-		.controller_data = (void *) GPIO_PTD5,
-	},
-};
+extern char ap325rxa_sdram_enter_start;
+extern char ap325rxa_sdram_enter_end;
+extern char ap325rxa_sdram_leave_start;
+extern char ap325rxa_sdram_leave_end;

 static int __init ap325rxa_devices_setup(void)
 {
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&ap325rxa_sdram_enter_start,
+					&ap325rxa_sdram_enter_end,
+					&ap325rxa_sdram_leave_start,
+					&ap325rxa_sdram_leave_end);
+
 	/* LD3 and LD4 LEDs */
 	gpio_request(GPIO_PTX5, NULL); /* RUN */
 	gpio_direction_output(GPIO_PTX5, 1);
@@ -578,12 +613,28 @@ static int __init ap325rxa_devices_setup(void)

 	platform_resource_setup_memory(&ceu_device, "ceu", 4 << 20);

+	/* SDHI0 - CN3 - SD CARD */
+	gpio_request(GPIO_FN_SDHI0CD_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0WP_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D3_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D2_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D1_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D0_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0CMD_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0CLK_PTD, NULL);
+
+	/* SDHI1 - CN7 - MICRO SD CARD */
+	gpio_request(GPIO_FN_SDHI1CD, NULL);
+	gpio_request(GPIO_FN_SDHI1D3, NULL);
+	gpio_request(GPIO_FN_SDHI1D2, NULL);
+	gpio_request(GPIO_FN_SDHI1D1, NULL);
+	gpio_request(GPIO_FN_SDHI1D0, NULL);
+	gpio_request(GPIO_FN_SDHI1CMD, NULL);
+	gpio_request(GPIO_FN_SDHI1CLK, NULL);
+
 	i2c_register_board_info(0, ap325rxa_i2c_devices,
 				ARRAY_SIZE(ap325rxa_i2c_devices));

-	spi_register_board_info(ap325rxa_spi_devices,
-				ARRAY_SIZE(ap325rxa_spi_devices));
-
 	return platform_add_devices(ap325rxa_devices,
 				ARRAY_SIZE(ap325rxa_devices));
 }
--- a/arch/sh/boards/mach-ecovec24/Makefile
+++ b/arch/sh/boards/mach-ecovec24/Makefile
@@ -6,4 +6,4 @@
 # for more details.
 #

-obj-y	 := setup.o
+obj-y	 := setup.o sdram.o
--- a/arch/sh/boards/mach-ecovec24/sdram.S
+++ b/arch/sh/boards/mach-ecovec24/sdram.S
@@ -0,0 +1,52 @@
+/*
+ * Ecovec24 sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(ecovec24_sdram_enter_start)
+
+	/* DBSC: put memory in self-refresh mode */
+
+	ED 0xFD000010, 0x00000000 /* DBEN */
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000040, 0x00000001 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(ecovec24_sdram_enter_end)
+
+	.balign 4
+ENTRY(ecovec24_sdram_leave_start)
+
+	/* DBSC: put memory in auto-refresh mode */
+
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	WAIT 1
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000010, 0x00000001 /* DBEN */
+	ED 0xFD000040, 0x00010000 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(ecovec24_sdram_leave_end)
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -20,12 +20,14 @@
 #include <linux/i2c.h>
 #include <linux/i2c/tsc2007.h>
 #include <linux/input.h>
+#include <linux/input/sh_keysc.h>
+#include <linux/mfd/sh_mobile_sdhi.h>
 #include <video/sh_mobile_lcdc.h>
 #include <media/sh_mobile_ceu.h>
 #include <asm/heartbeat.h>
 #include <asm/sh_eth.h>
-#include <asm/sh_keysc.h>
 #include <asm/clock.h>
+#include <asm/suspend.h>
 #include <cpu/sh7724.h>

 /*
@@ -147,6 +149,9 @@ static struct platform_device sh_eth_device = {
 	},
 	.num_resources = ARRAY_SIZE(sh_eth_resources),
 	.resource = sh_eth_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_ETHER,
+	},
 };

 /* USB0 host */
@@ -185,30 +190,18 @@ static struct platform_device usb0_host_device = {
 	.resource	= usb0_host_resources,
 };

-/*
- * USB1
- *
- * CN5 can use both host/function,
- * and we can determine it by checking PTB[3]
- *
- * This time only USB1 host is supported.
- */
+/* USB1 host/function */
 void usb1_port_power(int port, int power)
 {
-	if (!gpio_get_value(GPIO_PTB3)) {
-		printk(KERN_ERR "USB1 function is not supported\n");
-		return;
-	}
-
 	gpio_set_value(GPIO_PTB5, power);
 }

-static struct r8a66597_platdata usb1_host_data = {
+static struct r8a66597_platdata usb1_common_data = {
 	.on_chip = 1,
 	.port_power = usb1_port_power,
 };

-static struct resource usb1_host_resources[] = {
+static struct resource usb1_common_resources[] = {
 	[0] = {
 		.start	= 0xa4d90000,
 		.end	= 0xa4d90124 - 1,
@@ -221,16 +214,16 @@ static struct resource usb1_host_resources[] = {
 	},
 };

-static struct platform_device usb1_host_device = {
-	.name		= "r8a66597_hcd",
+static struct platform_device usb1_common_device = {
+	/* .name will be added in arch_setup */
 	.id		= 1,
 	.dev = {
 		.dma_mask		= NULL,         /*  not use dma */
 		.coherent_dma_mask	= 0xffffffff,
-		.platform_data		= &usb1_host_data,
+		.platform_data		= &usb1_common_data,
 	},
-	.num_resources	= ARRAY_SIZE(usb1_host_resources),
-	.resource	= usb1_host_resources,
+	.num_resources	= ARRAY_SIZE(usb1_common_resources),
+	.resource	= usb1_common_resources,
 };

 /* LCDC */
@@ -428,16 +421,90 @@ static struct i2c_board_info ts_i2c_clients = {
 	.irq		= IRQ0,
 };

+/* SHDI0 */
+static void sdhi0_set_pwr(struct platform_device *pdev, int state)
+{
+	gpio_set_value(GPIO_PTB6, state);
+}
+
+static struct sh_mobile_sdhi_info sdhi0_info = {
+	.set_pwr = sdhi0_set_pwr,
+};
+
+static struct resource sdhi0_resources[] = {
+	[0] = {
+		.name	= "SDHI0",
+		.start  = 0x04ce0000,
+		.end    = 0x04ce01ff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 101,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi0_device = {
+	.name           = "sh_mobile_sdhi",
+	.num_resources  = ARRAY_SIZE(sdhi0_resources),
+	.resource       = sdhi0_resources,
+	.id             = 0,
+	.dev	= {
+		.platform_data	= &sdhi0_info,
+	},
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI0,
+	},
+};
+
+/* SHDI1 */
+static void sdhi1_set_pwr(struct platform_device *pdev, int state)
+{
+	gpio_set_value(GPIO_PTB7, state);
+}
+
+static struct sh_mobile_sdhi_info sdhi1_info = {
+	.set_pwr = sdhi1_set_pwr,
+};
+
+static struct resource sdhi1_resources[] = {
+	[0] = {
+		.name	= "SDHI1",
+		.start  = 0x04cf0000,
+		.end    = 0x04cf01ff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 24,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi1_device = {
+	.name           = "sh_mobile_sdhi",
+	.num_resources  = ARRAY_SIZE(sdhi1_resources),
+	.resource       = sdhi1_resources,
+	.id             = 1,
+	.dev	= {
+		.platform_data	= &sdhi1_info,
+	},
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI1,
+	},
+};
+
 static struct platform_device *ecovec_devices[] __initdata = {
 	&heartbeat_device,
 	&nor_flash_device,
 	&sh_eth_device,
 	&usb0_host_device,
-	&usb1_host_device, /* USB1 host support */
+	&usb1_common_device,
 	&lcdc_device,
 	&ceu0_device,
 	&ceu1_device,
 	&keysc_device,
+	&sdhi0_device,
+	&sdhi1_device,
 };

 #define EEPROM_ADDR 0x50
@@ -466,12 +533,9 @@ static u8 mac_read(struct i2c_adapter *a, u8 command)
 	return buf;
 }

-#define MAC_LEN 6
-static void __init sh_eth_init(void)
+static void __init sh_eth_init(struct sh_eth_plat_data *pd)
 {
 	struct i2c_adapter *a = i2c_get_adapter(1);
-	struct clk *eth_clk;
-	u8 mac[MAC_LEN];
 	int i;

 	if (!a) {
@@ -479,39 +543,30 @@ static void __init sh_eth_init(void)
 		return;
 	}

-	eth_clk = clk_get(NULL, "eth0");
-	if (!eth_clk) {
-		pr_err("can not get eth0 clk\n");
-		return;
-	}
-
 	/* read MAC address frome EEPROM */
-	for (i = 0; i < MAC_LEN; i++) {
-		mac[i] = mac_read(a, 0x10 + i);
+	for (i = 0; i < sizeof(pd->mac_addr); i++) {
+		pd->mac_addr[i] = mac_read(a, 0x10 + i);
 		msleep(10);
 	}
-
-	/* clock enable */
-	clk_enable(eth_clk);
-
-	/* reset sh-eth */
-	ctrl_outl(0x1, SH_ETH_ADDR + 0x0);
-
-	/* set MAC addr */
-	ctrl_outl((mac[0] << 24) |
-		  (mac[1] << 16) |
-		  (mac[2] <<  8) |
-		  (mac[3] <<  0), SH_ETH_MAHR);
-	ctrl_outl((mac[4] <<  8) |
-		  (mac[5] <<  0), SH_ETH_MALR);
-
-	clk_put(eth_clk);
 }

 #define PORT_HIZA 0xA4050158
 #define IODRIVEA  0xA405018A
+
+extern char ecovec24_sdram_enter_start;
+extern char ecovec24_sdram_enter_end;
+extern char ecovec24_sdram_leave_start;
+extern char ecovec24_sdram_leave_end;
+
 static int __init arch_setup(void)
 {
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&ecovec24_sdram_enter_start,
+					&ecovec24_sdram_enter_end,
+					&ecovec24_sdram_leave_start,
+					&ecovec24_sdram_leave_end);
+
 	/* enable STATUS0, STATUS2 and PDSTATUS */
 	gpio_request(GPIO_FN_STATUS0, NULL);
 	gpio_request(GPIO_FN_STATUS2, NULL);
@@ -561,6 +616,14 @@ static int __init arch_setup(void)
 	ctrl_outw(0x0600, 0xa40501d4);
 	ctrl_outw(0x0600, 0xa4050192);

+	if (gpio_get_value(GPIO_PTB3)) {
+		printk(KERN_INFO "USB1 function is selected\n");
+		usb1_common_device.name = "r8a66597_udc";
+	} else {
+		printk(KERN_INFO "USB1 host is selected\n");
+		usb1_common_device.name = "r8a66597_hcd";
+	}
+
 	/* enable LCDC */
 	gpio_request(GPIO_FN_LCDD23,   NULL);
 	gpio_request(GPIO_FN_LCDD22,   NULL);
@@ -603,8 +666,8 @@ static int __init arch_setup(void)
 	gpio_direction_output(GPIO_PTR1, 0);
 	gpio_direction_output(GPIO_PTA2, 0);

-	/* I/O buffer drive ability is low */
-	ctrl_outw((ctrl_inw(IODRIVEA) & ~0x00c0) | 0x0040 , IODRIVEA);
+	/* I/O buffer drive ability is high */
+	ctrl_outw((ctrl_inw(IODRIVEA) & ~0x00c0) | 0x0080 , IODRIVEA);

 	if (gpio_get_value(GPIO_PTE6)) {
 		/* DVI */
@@ -710,6 +773,33 @@ static int __init arch_setup(void)
 	gpio_direction_input(GPIO_PTR5);
 	gpio_direction_input(GPIO_PTR6);

+	/* enable SDHI0 (needs DS2.4 set to ON) */
+	gpio_request(GPIO_FN_SDHI0CD,  NULL);
+	gpio_request(GPIO_FN_SDHI0WP,  NULL);
+	gpio_request(GPIO_FN_SDHI0CMD, NULL);
+	gpio_request(GPIO_FN_SDHI0CLK, NULL);
+	gpio_request(GPIO_FN_SDHI0D3,  NULL);
+	gpio_request(GPIO_FN_SDHI0D2,  NULL);
+	gpio_request(GPIO_FN_SDHI0D1,  NULL);
+	gpio_request(GPIO_FN_SDHI0D0,  NULL);
+	gpio_request(GPIO_PTB6, NULL);
+	gpio_direction_output(GPIO_PTB6, 0);
+
+	/* enable SDHI1 (needs DS2.6,7 set to ON,OFF) */
+	gpio_request(GPIO_FN_SDHI1CD,  NULL);
+	gpio_request(GPIO_FN_SDHI1WP,  NULL);
+	gpio_request(GPIO_FN_SDHI1CMD, NULL);
+	gpio_request(GPIO_FN_SDHI1CLK, NULL);
+	gpio_request(GPIO_FN_SDHI1D3,  NULL);
+	gpio_request(GPIO_FN_SDHI1D2,  NULL);
+	gpio_request(GPIO_FN_SDHI1D1,  NULL);
+	gpio_request(GPIO_FN_SDHI1D0,  NULL);
+	gpio_request(GPIO_PTB7, NULL);
+	gpio_direction_output(GPIO_PTB7, 0);
+
+	/* I/O buffer drive ability is high for SDHI1 */
+	ctrl_outw((ctrl_inw(IODRIVEA) & ~0x3000) | 0x2000 , IODRIVEA);
+
 	/* enable I2C device */
 	i2c_register_board_info(1, i2c1_devices,
 				ARRAY_SIZE(i2c1_devices));
@@ -721,12 +811,11 @@ arch_initcall(arch_setup);

 static int __init devices_setup(void)
 {
-	sh_eth_init();
+	sh_eth_init(&sh_eth_plat);
 	return 0;
 }
 device_initcall(devices_setup);

-
 static struct sh_machine_vector mv_ecovec __initmv = {
 	.mv_name	= "R0P7724 (EcoVec)",
 };
--- a/arch/sh/boards/mach-highlander/setup.c
+++ b/arch/sh/boards/mach-highlander/setup.c
@@ -384,7 +384,7 @@ static unsigned char irl2irq[HL_NR_IRL];

 static int highlander_irq_demux(int irq)
 {
-	if (irq >= HL_NR_IRL || !irl2irq[irq])
+	if (irq >= HL_NR_IRL || irq < 0 || !irl2irq[irq])
 		return irq;

 	return irl2irq[irq];
--- a/arch/sh/boards/mach-kfr2r09/Makefile
+++ b/arch/sh/boards/mach-kfr2r09/Makefile
@@ -1,2 +1,2 @@
-obj-y	 := setup.o
+obj-y	 := setup.o sdram.o
 obj-$(CONFIG_FB_SH_MOBILE_LCDC)	+=  lcd_wqvga.o
--- a/arch/sh/boards/mach-kfr2r09/sdram.S
+++ b/arch/sh/boards/mach-kfr2r09/sdram.S
@@ -0,0 +1,80 @@
+/*
+ * KFR2R09 sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(kfr2r09_sdram_enter_start)
+
+	/* DBSC: put memory in self-refresh mode */
+
+	ED 0xFD000010, 0x00000000 /* DBEN */
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000040, 0x00000001 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(kfr2r09_sdram_enter_end)
+
+	.balign 4
+ENTRY(kfr2r09_sdram_leave_start)
+
+	/* DBSC: put memory in auto-refresh mode */
+
+	mov.l	@(SH_SLEEP_MODE, r5), r0
+	tst	#SUSP_SH_RSTANDBY, r0
+	bf	resume_rstandby
+
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	WAIT 1
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000010, 0x00000001 /* DBEN */
+	ED 0xFD000040, 0x00010000 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+resume_rstandby:
+
+	/* DBSC: re-initialize and put in auto-refresh */
+
+	ED 0xFD000108, 0x40000301 /* DBPDCNT0 */
+	ED 0xFD000020, 0x011B0002 /* DBCONF */
+	ED 0xFD000030, 0x03060E02 /* DBTR0 */
+	ED 0xFD000034, 0x01020102 /* DBTR1 */
+	ED 0xFD000038, 0x01090406 /* DBTR2 */
+	ED 0xFD000008, 0x00000004 /* DBKIND */
+	ED 0xFD000040, 0x00000001 /* DBRFPDN0 */
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	ED 0xFD000018, 0x00000001 /* DBCKECNT */
+	WAIT 1
+	ED 0xFD000010, 0x00000001 /* DBEN */
+	ED 0xFD000044, 0x000004AF /* DBRFPDN1 */
+	ED 0xFD000048, 0x20CF0037 /* DBRFPDN2 */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000108, 0x40000300 /* DBPDCNT0 */
+	ED 0xFD000040, 0x00010000 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(kfr2r09_sdram_leave_end)
--- a/arch/sh/boards/mach-kfr2r09/setup.c
+++ b/arch/sh/boards/mach-kfr2r09/setup.c
@@ -16,13 +16,16 @@
 #include <linux/clk.h>
 #include <linux/gpio.h>
 #include <linux/input.h>
+#include <linux/input/sh_keysc.h>
 #include <linux/i2c.h>
 #include <linux/usb/r8a66597.h>
+#include <media/soc_camera.h>
+#include <media/sh_mobile_ceu.h>
 #include <video/sh_mobile_lcdc.h>
+#include <asm/suspend.h>
 #include <asm/clock.h>
 #include <asm/machvec.h>
 #include <asm/io.h>
-#include <asm/sh_keysc.h>
 #include <cpu/sh7724.h>
 #include <mach/kfr2r09.h>

@@ -212,11 +215,154 @@ static struct platform_device kfr2r09_usb0_gadget_device = {
 	.resource	= kfr2r09_usb0_gadget_resources,
 };

+static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
+	.flags = SH_CEU_FLAG_USE_8BIT_BUS,
+};
+
+static struct resource kfr2r09_ceu_resources[] = {
+	[0] = {
+		.name	= "CEU",
+		.start	= 0xfe910000,
+		.end	= 0xfe91009f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 52,
+		.end  = 52,
+		.flags  = IORESOURCE_IRQ,
+	},
+	[2] = {
+		/* place holder for contiguous memory */
+	},
+};
+
+static struct platform_device kfr2r09_ceu_device = {
+	.name		= "sh_mobile_ceu",
+	.id             = 0, /* "ceu0" clock */
+	.num_resources	= ARRAY_SIZE(kfr2r09_ceu_resources),
+	.resource	= kfr2r09_ceu_resources,
+	.dev	= {
+		.platform_data	= &sh_mobile_ceu_info,
+	},
+	.archdata = {
+		.hwblk_id = HWBLK_CEU0,
+	},
+};
+
+static struct i2c_board_info kfr2r09_i2c_camera = {
+	I2C_BOARD_INFO("rj54n1cb0c", 0x50),
+};
+
+static struct clk *camera_clk;
+
+#define DRVCRB 0xA405018C
+static int camera_power(struct device *dev, int mode)
+{
+	int ret;
+
+	if (mode) {
+		long rate;
+
+		camera_clk = clk_get(NULL, "video_clk");
+		if (IS_ERR(camera_clk))
+			return PTR_ERR(camera_clk);
+
+		/* set VIO_CKO clock to 25MHz */
+		rate = clk_round_rate(camera_clk, 25000000);
+		ret = clk_set_rate(camera_clk, rate);
+		if (ret < 0)
+			goto eclkrate;
+
+		/* set DRVCRB
+		 *
+		 * use 1.8 V for VccQ_VIO
+		 * use 2.85V for VccQ_SR
+		 */
+		ctrl_outw((ctrl_inw(DRVCRB) & ~0x0003) | 0x0001, DRVCRB);
+
+		/* reset clear */
+		ret = gpio_request(GPIO_PTB4, NULL);
+		if (ret < 0)
+			goto eptb4;
+		ret = gpio_request(GPIO_PTB7, NULL);
+		if (ret < 0)
+			goto eptb7;
+
+		ret = gpio_direction_output(GPIO_PTB4, 1);
+		if (!ret)
+			ret = gpio_direction_output(GPIO_PTB7, 1);
+		if (ret < 0)
+			goto egpioout;
+		msleep(1);
+
+		ret = clk_enable(camera_clk);	/* start VIO_CKO */
+		if (ret < 0)
+			goto eclkon;
+
+		return 0;
+	}
+
+	ret = 0;
+
+	clk_disable(camera_clk);
+eclkon:
+	gpio_set_value(GPIO_PTB7, 0);
+egpioout:
+	gpio_set_value(GPIO_PTB4, 0);
+	gpio_free(GPIO_PTB7);
+eptb7:
+	gpio_free(GPIO_PTB4);
+eptb4:
+eclkrate:
+	clk_put(camera_clk);
+	return ret;
+}
+
+static struct soc_camera_link rj54n1_link = {
+	.power		= camera_power,
+	.board_info	= &kfr2r09_i2c_camera,
+	.i2c_adapter_id	= 1,
+	.module_name	= "rj54n1cb0c",
+};
+
+static struct platform_device kfr2r09_camera = {
+	.name	= "soc-camera-pdrv",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &rj54n1_link,
+	},
+};
+
+static struct resource kfr2r09_sh_sdhi0_resources[] = {
+	[0] = {
+		.name	= "SDHI0",
+		.start  = 0x04ce0000,
+		.end    = 0x04ce01ff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 101,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device kfr2r09_sh_sdhi0_device = {
+	.name           = "sh_mobile_sdhi",
+	.num_resources  = ARRAY_SIZE(kfr2r09_sh_sdhi0_resources),
+	.resource       = kfr2r09_sh_sdhi0_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI0,
+	},
+};
+
 static struct platform_device *kfr2r09_devices[] __initdata = {
 	&kfr2r09_nor_flash_device,
 	&kfr2r09_nand_flash_device,
 	&kfr2r09_sh_keysc_device,
 	&kfr2r09_sh_lcdc_device,
+	&kfr2r09_ceu_device,
+	&kfr2r09_camera,
+	&kfr2r09_sh_sdhi0_device,
 };

 #define BSC_CS0BCR 0xfec10004
@@ -268,11 +414,59 @@ static int kfr2r09_usb0_gadget_i2c_setup(void)

 	return 0;
 }
+
+static int kfr2r09_serial_i2c_setup(void)
+{
+	struct i2c_adapter *a;
+	struct i2c_msg msg;
+	unsigned char buf[2];
+	int ret;
+
+	a = i2c_get_adapter(0);
+	if (!a)
+		return -ENODEV;
+
+	/* set bit 6 (the 7th bit) of chip at 0x09, register 0x13 */
+	buf[0] = 0x13;
+	msg.addr = 0x09;
+	msg.buf = buf;
+	msg.len = 1;
+	msg.flags = 0;
+	ret = i2c_transfer(a, &msg, 1);
+	if (ret != 1)
+		return -ENODEV;
+
+	buf[0] = 0;
+	msg.addr = 0x09;
+	msg.buf = buf;
+	msg.len = 1;
+	msg.flags = I2C_M_RD;
+	ret = i2c_transfer(a, &msg, 1);
+	if (ret != 1)
+		return -ENODEV;
+
+	buf[1] = buf[0] | (1 << 6);
+	buf[0] = 0x13;
+	msg.addr = 0x09;
+	msg.buf = buf;
+	msg.len = 2;
+	msg.flags = 0;
+	ret = i2c_transfer(a, &msg, 1);
+	if (ret != 1)
+		return -ENODEV;
+
+	return 0;
+}
 #else
 static int kfr2r09_usb0_gadget_i2c_setup(void)
 {
 	return -ENODEV;
 }
+
+static int kfr2r09_serial_i2c_setup(void)
+{
+	return -ENODEV;
+}
 #endif

 static int kfr2r09_usb0_gadget_setup(void)
@@ -299,11 +493,27 @@ static int kfr2r09_usb0_gadget_setup(void)
 	return 0;
 }

+extern char kfr2r09_sdram_enter_start;
+extern char kfr2r09_sdram_enter_end;
+extern char kfr2r09_sdram_leave_start;
+extern char kfr2r09_sdram_leave_end;
+
 static int __init kfr2r09_devices_setup(void)
 {
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF |
+					SUSP_SH_RSTANDBY,
+					&kfr2r09_sdram_enter_start,
+					&kfr2r09_sdram_enter_end,
+					&kfr2r09_sdram_leave_start,
+					&kfr2r09_sdram_leave_end);
+
 	/* enable SCIF1 serial port for YC401 console support */
 	gpio_request(GPIO_FN_SCIF1_RXD, NULL);
 	gpio_request(GPIO_FN_SCIF1_TXD, NULL);
+	kfr2r09_serial_i2c_setup(); /* ECONTMSK(bit6=L10ONEN) set 1 */
+	gpio_request(GPIO_PTG3, NULL); /* HPON_ON */
+	gpio_direction_output(GPIO_PTG3, 1); /* HPON_ON = H */

 	/* setup NOR flash at CS0 */
 	ctrl_outl(0x36db0400, BSC_CS0BCR);
@@ -361,6 +571,32 @@ static int __init kfr2r09_devices_setup(void)
 	if (kfr2r09_usb0_gadget_setup() == 0)
 		platform_device_register(&kfr2r09_usb0_gadget_device);

+	/* CEU */
+	gpio_request(GPIO_FN_VIO_CKO, NULL);
+	gpio_request(GPIO_FN_VIO0_CLK, NULL);
+	gpio_request(GPIO_FN_VIO0_VD, NULL);
+	gpio_request(GPIO_FN_VIO0_HD, NULL);
+	gpio_request(GPIO_FN_VIO0_FLD, NULL);
+	gpio_request(GPIO_FN_VIO0_D7, NULL);
+	gpio_request(GPIO_FN_VIO0_D6, NULL);
+	gpio_request(GPIO_FN_VIO0_D5, NULL);
+	gpio_request(GPIO_FN_VIO0_D4, NULL);
+	gpio_request(GPIO_FN_VIO0_D3, NULL);
+	gpio_request(GPIO_FN_VIO0_D2, NULL);
+	gpio_request(GPIO_FN_VIO0_D1, NULL);
+	gpio_request(GPIO_FN_VIO0_D0, NULL);
+
+	platform_resource_setup_memory(&kfr2r09_ceu_device, "ceu", 4 << 20);
+
+	/* SDHI0 connected to yc304 */
+	gpio_request(GPIO_FN_SDHI0CD, NULL);
+	gpio_request(GPIO_FN_SDHI0D3, NULL);
+	gpio_request(GPIO_FN_SDHI0D2, NULL);
+	gpio_request(GPIO_FN_SDHI0D1, NULL);
+	gpio_request(GPIO_FN_SDHI0D0, NULL);
+	gpio_request(GPIO_FN_SDHI0CMD, NULL);
+	gpio_request(GPIO_FN_SDHI0CLK, NULL);
+
 	return platform_add_devices(kfr2r09_devices,
 				    ARRAY_SIZE(kfr2r09_devices));
 }
--- a/arch/sh/boards/mach-migor/Makefile
+++ b/arch/sh/boards/mach-migor/Makefile
@@ -1,2 +1,2 @@
-obj-y	 := setup.o
+obj-y	 := setup.o sdram.o
 obj-$(CONFIG_SH_MIGOR_QVGA)	+=  lcd_qvga.o
--- a/arch/sh/boards/mach-migor/sdram.S
+++ b/arch/sh/boards/mach-migor/sdram.S
@@ -0,0 +1,69 @@
+/*
+ * Migo-R sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(migor_sdram_enter_start)
+
+	/* SBSC: disable power down and put in self-refresh mode */
+	mov.l	1f, r4
+	mov.l	2f, r1
+	mov.l	@r4, r2
+	or	r1, r2
+	mov.l   3f, r3
+	and	r3, r2
+	mov.l	r2, @r4
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+2:	.long	0x00000400
+3:	.long	0xffff7fff
+ENTRY(migor_sdram_enter_end)
+
+	.balign 4
+ENTRY(migor_sdram_leave_start)
+
+	/* SBSC: set auto-refresh mode */
+	mov.l	1f, r4
+	mov.l	@r4, r0
+	mov.l   4f, r1
+	and	r1, r0
+	mov.l	r0, @r4
+	mov.l	6f, r4
+	mov.l	8f, r0
+	mov.l	@r4, r1
+	mov	#-1, r4
+	add	r4, r1
+	or	r1, r0
+	mov.l	7f, r1
+	mov.l	r0, @r1
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+4:	.long	0xfffffbff
+6:	.long   0xfe40001c /* RTCOR */
+7:	.long   0xfe400018 /* RTCNT */
+8:	.long   0xa55a0000
+ENTRY(migor_sdram_leave_end)
--- a/arch/sh/boards/mach-migor/setup.c
+++ b/arch/sh/boards/mach-migor/setup.c
@@ -11,6 +11,7 @@
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
 #include <linux/input.h>
+#include <linux/input/sh_keysc.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/nand.h>
 #include <linux/i2c.h>
@@ -18,8 +19,6 @@
 #include <linux/delay.h>
 #include <linux/clk.h>
 #include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_gpio.h>
 #include <video/sh_mobile_lcdc.h>
 #include <media/sh_mobile_ceu.h>
 #include <media/ov772x.h>
@@ -27,7 +26,7 @@
 #include <asm/clock.h>
 #include <asm/machvec.h>
 #include <asm/io.h>
-#include <asm/sh_keysc.h>
+#include <asm/suspend.h>
 #include <mach/migor.h>
 #include <cpu/sh7722.h>

@@ -390,17 +389,25 @@ static struct platform_device migor_ceu_device = {
 	},
 };

-struct spi_gpio_platform_data sdcard_cn9_platform_data = {
-	.sck = GPIO_PTD0,
-	.mosi = GPIO_PTD1,
-	.miso = GPIO_PTD2,
-	.num_chipselect = 1,
+static struct resource sdhi_cn9_resources[] = {
+	[0] = {
+		.name	= "SDHI",
+		.start	= 0x04ce0000,
+		.end	= 0x04ce01ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 101,
+		.flags  = IORESOURCE_IRQ,
+	},
 };

-static struct platform_device sdcard_cn9_device = {
-	.name		= "spi_gpio",
-	.dev	= {
-		.platform_data	= &sdcard_cn9_platform_data,
+static struct platform_device sdhi_cn9_device = {
+	.name		= "sh_mobile_sdhi",
+	.num_resources	= ARRAY_SIZE(sdhi_cn9_resources),
+	.resource	= sdhi_cn9_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI,
 	},
 };

@@ -467,23 +474,24 @@ static struct platform_device *migor_devices[] __initdata = {
 	&migor_ceu_device,
 	&migor_nor_flash_device,
 	&migor_nand_flash_device,
-	&sdcard_cn9_device,
+	&sdhi_cn9_device,
 	&migor_camera[0],
 	&migor_camera[1],
 };

-static struct spi_board_info migor_spi_devices[] = {
-	{
-		.modalias = "mmc_spi",
-		.max_speed_hz = 5000000,
-		.chip_select = 0,
-		.controller_data = (void *) GPIO_PTD5,
-	},
-};
+extern char migor_sdram_enter_start;
+extern char migor_sdram_enter_end;
+extern char migor_sdram_leave_start;
+extern char migor_sdram_leave_end;

 static int __init migor_devices_setup(void)
 {
-
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&migor_sdram_enter_start,
+					&migor_sdram_enter_end,
+					&migor_sdram_leave_start,
+					&migor_sdram_leave_end);
 #ifdef CONFIG_PM
 	/* Let D11 LED show STATUS0 */
 	gpio_request(GPIO_FN_STATUS0, NULL);
@@ -525,6 +533,16 @@ static int __init migor_devices_setup(void)
 	gpio_request(GPIO_PTA1, NULL);
 	gpio_direction_input(GPIO_PTA1);

+	/* SDHI */
+	gpio_request(GPIO_FN_SDHICD, NULL);
+	gpio_request(GPIO_FN_SDHIWP, NULL);
+	gpio_request(GPIO_FN_SDHID3, NULL);
+	gpio_request(GPIO_FN_SDHID2, NULL);
+	gpio_request(GPIO_FN_SDHID1, NULL);
+	gpio_request(GPIO_FN_SDHID0, NULL);
+	gpio_request(GPIO_FN_SDHICMD, NULL);
+	gpio_request(GPIO_FN_SDHICLK, NULL);
+
 	/* Touch Panel */
 	gpio_request(GPIO_FN_IRQ6, NULL);

@@ -612,9 +630,6 @@ static int __init migor_devices_setup(void)
 	i2c_register_board_info(0, migor_i2c_devices,
 				ARRAY_SIZE(migor_i2c_devices));

-	spi_register_board_info(migor_spi_devices,
-				ARRAY_SIZE(migor_spi_devices));
-
 	return platform_add_devices(migor_devices, ARRAY_SIZE(migor_devices));
 }
 arch_initcall(migor_devices_setup);
--- a/arch/sh/boards/mach-r2d/irq.c
+++ b/arch/sh/boards/mach-r2d/irq.c
@@ -116,7 +116,7 @@ static unsigned char irl2irq[R2D_NR_IRL];

 int rts7751r2d_irq_demux(int irq)
 {
-	if (irq >= R2D_NR_IRL || !irl2irq[irq])
+	if (irq >= R2D_NR_IRL || irq < 0 || !irl2irq[irq])
 		return irq;

 	return irl2irq[irq];
--- a/arch/sh/boards/mach-se/7722/irq.c
+++ b/arch/sh/boards/mach-se/7722/irq.c
@@ -16,15 +16,17 @@
 #include <asm/io.h>
 #include <mach-se/mach/se7722.h>

+unsigned int se7722_fpga_irq[SE7722_FPGA_IRQ_NR] = { 0, };
+
 static void disable_se7722_irq(unsigned int irq)
 {
-	unsigned int bit = irq - SE7722_FPGA_IRQ_BASE;
+	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
 	ctrl_outw(ctrl_inw(IRQ01_MASK) | 1 << bit, IRQ01_MASK);
 }

 static void enable_se7722_irq(unsigned int irq)
 {
-	unsigned int bit = irq - SE7722_FPGA_IRQ_BASE;
+	unsigned int bit = (unsigned int)get_irq_chip_data(irq);
 	ctrl_outw(ctrl_inw(IRQ01_MASK) & ~(1 << bit), IRQ01_MASK);
 }

@@ -38,18 +40,15 @@ static struct irq_chip se7722_irq_chip __read_mostly = {
 static void se7722_irq_demux(unsigned int irq, struct irq_desc *desc)
 {
 	unsigned short intv = ctrl_inw(IRQ01_STS);
-	struct irq_desc *ext_desc;
-	unsigned int ext_irq = SE7722_FPGA_IRQ_BASE;
+	unsigned int ext_irq = 0;

 	intv &= (1 << SE7722_FPGA_IRQ_NR) - 1;

-	while (intv) {
-		if (intv & 1) {
-			ext_desc = irq_desc + ext_irq;
-			handle_level_irq(ext_irq, ext_desc);
-		}
-		intv >>= 1;
-		ext_irq++;
+	for (; intv; intv >>= 1, ext_irq++) {
+		if (!(intv & 1))
+			continue;
+
+		generic_handle_irq(se7722_fpga_irq[ext_irq]);
 	}
 }

@@ -63,11 +62,18 @@ void __init init_se7722_IRQ(void)
 	ctrl_outw(0, IRQ01_MASK);       /* disable all irqs */
 	ctrl_outw(0x2000, 0xb03fffec);  /* mrshpc irq enable */

-	for (i = 0; i < SE7722_FPGA_IRQ_NR; i++)
-		set_irq_chip_and_handler_name(SE7722_FPGA_IRQ_BASE + i,
+	for (i = 0; i < SE7722_FPGA_IRQ_NR; i++) {
+		se7722_fpga_irq[i] = create_irq();
+		if (se7722_fpga_irq[i] < 0)
+			return;
+
+		set_irq_chip_and_handler_name(se7722_fpga_irq[i],
 					      &se7722_irq_chip,
 					      handle_level_irq, "level");

+		set_irq_chip_data(se7722_fpga_irq[i], (void *)i);
+	}
+
 	set_irq_chained_handler(IRQ0_IRQ, se7722_irq_demux);
 	set_irq_type(IRQ0_IRQ, IRQ_TYPE_LEVEL_LOW);

--- a/arch/sh/boards/mach-se/7722/setup.c
+++ b/arch/sh/boards/mach-se/7722/setup.c
@@ -14,6 +14,7 @@
 #include <linux/platform_device.h>
 #include <linux/ata_platform.h>
 #include <linux/input.h>
+#include <linux/input/sh_keysc.h>
 #include <linux/smc91x.h>
 #include <mach-se/mach/se7722.h>
 #include <mach-se/mach/mrshpc.h>
@@ -21,7 +22,6 @@
 #include <asm/clock.h>
 #include <asm/io.h>
 #include <asm/heartbeat.h>
-#include <asm/sh_keysc.h>
 #include <cpu/sh7722.h>

 /* Heartbeat */
@@ -60,8 +60,7 @@ static struct resource smc91x_eth_resources[] = {
 		.flags  = IORESOURCE_MEM,
 	},
 	[1] = {
-		.start  = SMC_IRQ,
-		.end    = SMC_IRQ,
+		/* Filled in later */
 		.flags  = IORESOURCE_IRQ,
 	},
 };
@@ -90,8 +89,7 @@ static struct resource cf_ide_resources[] = {
 		.flags  = IORESOURCE_IO,
 	},
 	[2] = {
-		.start  = MRSHPC_IRQ0,
-		.end    = MRSHPC_IRQ0,
+		/* Filled in later */
 		.flags  = IORESOURCE_IRQ,
 	},
 };
@@ -153,6 +151,14 @@ static struct platform_device *se7722_devices[] __initdata = {
 static int __init se7722_devices_setup(void)
 {
 	mrshpc_setup_windows();
+
+	/* Wire-up dynamic vectors */
+	cf_ide_resources[2].start = cf_ide_resources[2].end =
+		se7722_fpga_irq[SE7722_FPGA_IRQ_MRSHPC0];
+
+	smc91x_eth_resources[1].start = smc91x_eth_resources[1].end =
+		se7722_fpga_irq[SE7722_FPGA_IRQ_SMC];
+
 	return platform_add_devices(se7722_devices, ARRAY_SIZE(se7722_devices));
 }
 device_initcall(se7722_devices_setup);
@@ -193,6 +199,5 @@ static void __init se7722_setup(char **cmdline_p)
 static struct sh_machine_vector mv_se7722 __initmv = {
 	.mv_name                = "Solution Engine 7722" ,
 	.mv_setup               = se7722_setup ,
-	.mv_nr_irqs		= SE7722_FPGA_IRQ_BASE + SE7722_FPGA_IRQ_NR,
 	.mv_init_irq		= init_se7722_IRQ,
 };
--- a/arch/sh/boards/mach-se/7724/Makefile
+++ b/arch/sh/boards/mach-se/7724/Makefile
@@ -7,4 +7,4 @@
 #
 #

-obj-y	 := setup.o irq.o
+obj-y	 := setup.o irq.o sdram.o
--- a/arch/sh/boards/mach-se/7724/sdram.S
+++ b/arch/sh/boards/mach-se/7724/sdram.S
@@ -0,0 +1,52 @@
+/*
+ * MS7724SE sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(ms7724se_sdram_enter_start)
+
+	/* DBSC: put memory in self-refresh mode */
+
+	ED 0xFD000010, 0x00000000 /* DBEN */
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000040, 0x00000001 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(ms7724se_sdram_enter_end)
+
+	.balign 4
+ENTRY(ms7724se_sdram_leave_start)
+
+	/* DBSC: put memory in auto-refresh mode */
+
+	ED 0xFD000040, 0x00000000 /* DBRFPDN0 */
+	WAIT 1
+	ED 0xFD000014, 0x00000002 /* DBCMDCNT (PALL) */
+	ED 0xFD000014, 0x00000004 /* DBCMDCNT (REF) */
+	ED 0xFD000010, 0x00000001 /* DBEN */
+	ED 0xFD000040, 0x00010000 /* DBRFPDN0 */
+
+	rts
+	 nop
+
+ENTRY(ms7724se_sdram_leave_end)
--- a/arch/sh/boards/mach-se/7724/setup.c
+++ b/arch/sh/boards/mach-se/7724/setup.c
@@ -19,6 +19,7 @@
 #include <linux/smc91x.h>
 #include <linux/gpio.h>
 #include <linux/input.h>
+#include <linux/input/sh_keysc.h>
 #include <linux/usb/r8a66597.h>
 #include <video/sh_mobile_lcdc.h>
 #include <media/sh_mobile_ceu.h>
@@ -27,7 +28,7 @@
 #include <asm/heartbeat.h>
 #include <asm/sh_eth.h>
 #include <asm/clock.h>
-#include <asm/sh_keysc.h>
+#include <asm/suspend.h>
 #include <cpu/sh7724.h>
 #include <mach-se/mach/se7724.h>

@@ -451,6 +452,52 @@ static struct platform_device sh7724_usb1_gadget_device = {
 	.resource	= sh7724_usb1_gadget_resources,
 };

+static struct resource sdhi0_cn7_resources[] = {
+	[0] = {
+		.name	= "SDHI0",
+		.start  = 0x04ce0000,
+		.end    = 0x04ce01ff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 101,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi0_cn7_device = {
+	.name           = "sh_mobile_sdhi",
+	.id		= 0,
+	.num_resources  = ARRAY_SIZE(sdhi0_cn7_resources),
+	.resource       = sdhi0_cn7_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI0,
+	},
+};
+
+static struct resource sdhi1_cn8_resources[] = {
+	[0] = {
+		.name	= "SDHI1",
+		.start  = 0x04cf0000,
+		.end    = 0x04cf01ff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 24,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi1_cn8_device = {
+	.name           = "sh_mobile_sdhi",
+	.id		= 1,
+	.num_resources  = ARRAY_SIZE(sdhi1_cn8_resources),
+	.resource       = sdhi1_cn8_resources,
+	.archdata = {
+		.hwblk_id = HWBLK_SDHI1,
+	},
+};
+
 static struct platform_device *ms7724se_devices[] __initdata = {
 	&heartbeat_device,
 	&smc91x_eth_device,
@@ -463,6 +510,8 @@ static struct platform_device *ms7724se_devices[] __initdata = {
 	&sh7724_usb0_host_device,
 	&sh7724_usb1_gadget_device,
 	&fsi_device,
+	&sdhi0_cn7_device,
+	&sdhi1_cn8_device,
 };

 #define EEPROM_OP   0xBA206000
@@ -487,7 +536,7 @@ static int __init sh_eth_is_eeprom_ready(void)
 static void __init sh_eth_init(void)
 {
 	int i;
-	u16 mac[3];
+	u16 mac;

 	/* check EEPROM status */
 	if (!sh_eth_is_eeprom_ready())
@@ -501,16 +550,10 @@ static void __init sh_eth_init(void)
 		if (!sh_eth_is_eeprom_ready())
 			return;

-		mac[i] = ctrl_inw(EEPROM_DATA);
-		mac[i] = ((mac[i] & 0xFF) << 8) | (mac[i] >> 8); /* swap */
+		mac = ctrl_inw(EEPROM_DATA);
+		sh_eth_plat.mac_addr[i << 1] = mac & 0xff;
+		sh_eth_plat.mac_addr[(i << 1) + 1] = mac >> 8;
 	}
-
-	/* reset sh-eth */
-	ctrl_outl(0x1, SH_ETH_ADDR + 0x0);
-
-	/* set MAC addr */
-	ctrl_outl(((mac[0] << 16) | (mac[1])), SH_ETH_MAHR);
-	ctrl_outl((mac[2]), SH_ETH_MALR);
 }

 #define SW4140    0xBA201000
@@ -527,11 +570,22 @@ static void __init sh_eth_init(void)
 #define SW41_G    0x4000
 #define SW41_H    0x8000

+extern char ms7724se_sdram_enter_start;
+extern char ms7724se_sdram_enter_end;
+extern char ms7724se_sdram_leave_start;
+extern char ms7724se_sdram_leave_end;
+
 static int __init devices_setup(void)
 {
 	u16 sw = ctrl_inw(SW4140); /* select camera, monitor */
 	struct clk *fsia_clk;

+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&ms7724se_sdram_enter_start,
+					&ms7724se_sdram_enter_end,
+					&ms7724se_sdram_leave_start,
+					&ms7724se_sdram_leave_end);
 	/* Reset Release */
 	ctrl_outw(ctrl_inw(FPGA_OUT) &
 		  ~((1 << 1)  | /* LAN */
@@ -701,6 +755,26 @@ static int __init devices_setup(void)
 	clk_set_rate(&fsimcka_clk, 11000);
 	clk_put(fsia_clk);

+	/* SDHI0 connected to cn7 */
+	gpio_request(GPIO_FN_SDHI0CD, NULL);
+	gpio_request(GPIO_FN_SDHI0WP, NULL);
+	gpio_request(GPIO_FN_SDHI0D3, NULL);
+	gpio_request(GPIO_FN_SDHI0D2, NULL);
+	gpio_request(GPIO_FN_SDHI0D1, NULL);
+	gpio_request(GPIO_FN_SDHI0D0, NULL);
+	gpio_request(GPIO_FN_SDHI0CMD, NULL);
+	gpio_request(GPIO_FN_SDHI0CLK, NULL);
+
+	/* SDHI1 connected to cn8 */
+	gpio_request(GPIO_FN_SDHI1CD, NULL);
+	gpio_request(GPIO_FN_SDHI1WP, NULL);
+	gpio_request(GPIO_FN_SDHI1D3, NULL);
+	gpio_request(GPIO_FN_SDHI1D2, NULL);
+	gpio_request(GPIO_FN_SDHI1D1, NULL);
+	gpio_request(GPIO_FN_SDHI1D0, NULL);
+	gpio_request(GPIO_FN_SDHI1CMD, NULL);
+	gpio_request(GPIO_FN_SDHI1CLK, NULL);
+
 	/*
 	 * enable SH-Eth
 	 *