Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull more input updates from Dmitry Torokhov:
 "Two new drivers for touchscreen controllers:

   - Silead touchscreen controllers
   - SiS 9200 family touchscreen controllers

  and a few driver fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: silead - remove some dead code
  Input: sis-i2c - select CONFIG_CRC_ITU_T
  Input: add driver for SiS 9200 family I2C touchscreen controllers
  Input: ili210x - fix permissions on "calibrate" attribute
  Input: elan_i2c - properly wake up touchpad on ASUS laptops
  Input: add driver for Silead touchscreens
  Input: elantech - fix debug dump of the current packet
  Input: rotary_encoder - support binary encoding of states
  Input: xpad - power off wireless 360 controllers on suspend
  Input: i8042 - break load dependency between atkbd/psmouse and i8042
  Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
  Input: cros_ec_keyb - cleanup use of dev

Documentation/devicetree/bindings/input/rotary-encoder.txt

@@ -20,6 +20,8 @@ Optional properties:
   2: Half-period mode
   4: Quarter-period mode
 - wakeup-source: Boolean, rotary encoder can wake up the system.
+- rotary-encoder,encoding: String, the method used to encode steps.
+  Supported are "gray" (the default and more common) and "binary".
 
 Deprecated properties:
 - rotary-encoder,half-period: Makes the driver work on half-period mode.
@@ -34,6 +36,7 @@ Example:
 			compatible = "rotary-encoder";
 			gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */
 			linux,axis = <0>; /* REL_X */
+			rotary-encoder,encoding = "gray";
 			rotary-encoder,relative-axis;
 		};
 
@@ -42,5 +45,6 @@ Example:
 			gpios = <&gpio 21 0>, <&gpio 22 0>;
 			linux,axis = <1>; /* ABS_Y */
 			rotary-encoder,steps = <24>;
+			rotary-encoder,encoding = "binary";
 			rotary-encoder,rollover;
 		};

Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt

@@ -0,0 +1,36 @@
+* GSL 1680 touchscreen controller
+
+Required properties:
+- compatible		  : "silead,gsl1680"
+- reg			  : I2C slave address of the chip (0x40)
+- interrupt-parent	  : a phandle pointing to the interrupt controller
+			    serving the interrupt for this chip
+- interrupts		  : interrupt specification for the gsl1680 interrupt
+- power-gpios		  : Specification for the pin connected to the gsl1680's
+			    shutdown input. This needs to be driven high to take the
+			    gsl1680 out of its low power state
+- touchscreen-size-x	  : See touchscreen.txt
+- touchscreen-size-y	  : See touchscreen.txt
+
+Optional properties:
+- touchscreen-inverted-x  : See touchscreen.txt
+- touchscreen-inverted-y  : See touchscreen.txt
+- touchscreen-swapped-x-y : See touchscreen.txt
+- silead,max-fingers	  : maximum number of fingers the touchscreen can detect
+
+Example:
+
+i2c@00000000 {
+	gsl1680: touchscreen@40 {
+		compatible = "silead,gsl1680";
+		reg = <0x40>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>;
+		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		touchscreen-inverted-x;
+		touchscreen-swapped-x-y;
+		silead,max-fingers = <5>;
+	};
+};

Documentation/devicetree/bindings/input/touchscreen/sis_i2c.txt

@@ -0,0 +1,33 @@
+* SiS I2C Multiple Touch Controller
+
+Required properties:
+- compatible: must be "sis,9200-ts"
+- reg: i2c slave address
+- interrupt-parent: the phandle for the interrupt controller
+  (see interrupt binding [0])
+- interrupts: touch controller interrupt (see interrupt
+  binding [0])
+
+Optional properties:
+- pinctrl-names: should be "default" (see pinctrl binding [1]).
+- pinctrl-0: a phandle pointing to the pin settings for the
+  device (see pinctrl binding [1]).
+- attn-gpios: the gpio pin used as attention line
+- reset-gpios: the gpio pin used to reset the controller
+- wakeup-source: touchscreen can be used as a wakeup source
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example:
+
+	sis9255@5c  {
+		compatible = "sis,9200-ts";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sis>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		irq-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
+	};