Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.10

Major changes:

iwlwifi

* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue

ath9k

* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
  latency and fix bufferbloat

wl18xx

* allow scanning in AP mode
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt

@@ -1,8 +1,8 @@
-Marvell 8897/8997 (sd8897/sd8997) SDIO devices
+Marvell 8897/8997 (sd8897/sd8997/pcie8997) SDIO/PCIE devices
 ------
 
-This node provides properties for controlling the marvell sdio wireless device.
-The node is expected to be specified as a child node to the SDIO controller that
+This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
+The node is expected to be specified as a child node to the SDIO/PCIE controller that
 connects the device to the system.
 
 Required properties:
@@ -10,6 +10,8 @@ Required properties:
   - compatible : should be one of the following:
 	* "marvell,sd8897"
 	* "marvell,sd8997"
+	* "pci11ab,2b42"
+	* "pci1b4b,2b42"
 
 Optional properties:
 

Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt

@@ -0,0 +1,48 @@
+* Qualcomm Atheros ath9k wireless devices
+
+This node provides properties for configuring the ath9k wireless device. The
+node is expected to be specified as a child node of the PCI controller to
+which the wireless chip is connected.
+
+Required properties:
+- compatible: For PCI and PCIe devices this should be an identifier following
+		the format as defined in "PCI Bus Binding to Open Firmware"
+		Revision 2.1. One of the possible formats is "pciVVVV,DDDD"
+		where VVVV is the PCI vendor ID and DDDD is PCI device ID.
+		Typically QCA's PCI vendor ID 168c is used while the PCI device
+		ID depends on the chipset - see the following (possibly
+		incomplete) list:
+			- 0023 for AR5416
+			- 0024 for AR5418
+			- 0027 for AR9160
+			- 0029 for AR9220 and AR9223
+			- 002a for AR9280 and AR9283
+			- 002b for AR9285
+			- 002c for AR2427
+			- 002d for AR9227
+			- 002e for AR9287
+			- 0030 for AR9380, AR9381 and AR9382
+			- 0032 for AR9485
+			- 0033 for AR9580 and AR9590
+			- 0034 for AR9462
+			- 0036 for AR9565
+			- 0037 for AR9485
+- reg: Address and length of the register set for the device.
+
+Optional properties:
+- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the
+			ath9k wireless chip (in this case the calibration /
+			EEPROM data will be loaded from userspace using the
+			kernel firmware loader).
+- mac-address: See ethernet.txt in the parent directory
+- local-mac-address: See ethernet.txt in the parent directory
+
+
+In this example, the node is defined as child node of the PCI controller:
+&pci0 {
+	wifi@168c,002d {
+		compatible = "pci168c,002d";
+		reg = <0x7000 0 0 0 0x1000>;
+		qca,no-eeprom;
+	};
+};